Im a redseal on road and off road mechanic with electromechanical background. I've watched a lot of videos over the years. You're video I watched here is by far the best. Based on knowledge and experience. Thorough , to the point and simple. I sure hope you are a teacher or instructor. Thanks.
installing the bearing shaft in this video,if press on the shaft may be cause for damaged the new bearing ?,and seem like the shaft had been pressed up side down then the impeller was touching with the housing and making grinding sound ?
It was the first time I replaced a bearing in a water pump. I should have pressed the bearing housing, but I don't think there will be any problems because I pressed the bearing shaft. The impeller does not touch the water pump housing, the grinding sound is due to the pulley rubbing against the hydraulic press holder.
might get me a 6 ton press at harbor frieght and rebuild my water pump on my ingersol rand compressor this looks pretty simple thanks for sharing and love your chickens might give them some water melon for a treat lol
good vid. I leart a lot. How about lube on the shaft? my buddy says he uses Co2 on the parts to shrink the metal and lubes the parts but this gets costly. Parts slide in without much pressure. My shop had a pressure ga on the unit so you wouldn't break or blow up parts and we also had a guard screen around the work area. be careful. using a press can be dangerous.
Salutare, hai sa mai detailam împreună ceva, am mai vazut un sistem de presare, la care folosea o bucsa și presa direct pe camasa exterioară a rulmentului, evita predarea pe bilele rulmentului.
M-am gandit odata ca s-ar putea sa afecteze rulmentul. Dar forta de apasare nu a fost asa mare. Rulmentul a intrat destul de usor in camasa pompei si am zis sa nu mai pierd timpul pentru confectionarea acelei bucse. Corect este cum ziceti dvs. apasarea trebuie facuta pe camasa rulmentului.
The hydraulic press is equipped with a 20-ton jack. The bearing came out quite hard. Maybe you should use a degreasing spray or maybe you need to heat the bearing.
@@DorelBorlea I used a 50 ton jack and still cant get it to move at all. I usually don’t have any problems working on my equipment but the water pump is new for me. I have tried everything. I took it to a friends house who had a 20 ton hydraulic jack and they laid a peace of flat iron on the shaft and it never moved, So I went and bought a 50 ton jack and it still didn’t move.
You don't press a bearing in by its shaft, you press it in by the OUTER RACE. you likely greatly shortened the life of that bearing by pushing it in via the shaft which is a huge no-no....
:) Naturalmente, no sé mucho sobre bombas de agua. Esta es la primera bomba de agua que reparo. No tienes que hacer lo mismo que yo. Procedí como pensé que era correcto, lo importante es que la bomba esté funcional y siga funcionando.
Estaba buscando información sobre cómo reparar una bomba de agua. No encontré mucho. Hice lo que pensé que era correcto. Incluso si empujé el eje central, consideré que no hay riesgo de dañar el rodamiento. El rodamiento entró con bastante facilidad y no resistió.
Im a redseal on road and off road mechanic with electromechanical background. I've watched a lot of videos over the years. You're video I watched here is by far the best. Based on knowledge and experience. Thorough , to the point and simple. I sure hope you are a teacher or instructor. Thanks.
Pressing the shaft instead of the race will ruin or severly shorten the life of the pump.
installing the bearing shaft in this video,if press on the shaft may be cause for damaged the new bearing ?,and seem like the shaft had been pressed up side down then the impeller was touching with the housing and making grinding sound ?
It was the first time I replaced a bearing in a water pump. I should have pressed the bearing housing, but I don't think there will be any problems because I pressed the bearing shaft. The impeller does not touch the water pump housing, the grinding sound is due to the pulley rubbing against the hydraulic press holder.
Plus press the bearing in on the outer race
might get me a 6 ton press at harbor frieght and rebuild my water pump on my ingersol rand compressor this looks pretty simple thanks for sharing and love your chickens might give them some water melon for a treat lol
Gracias por el video muy amable exelente
Me alegro de que este video haya sido útil
Just did this on a jd pump and broke the pulley groove ,best to pull the pulley and press out from the impeller side
good vid. I leart a lot. How about lube on the shaft? my buddy says he uses Co2 on the parts to shrink the metal and lubes the parts but this gets costly. Parts slide in without much pressure. My shop had a pressure ga on the unit so you wouldn't break or blow up parts and we also had a guard screen around the work area. be careful. using a press can be dangerous.
And there goes the bearings
The repair was a success. The water pump is still working. ;)
@@DorelBorlea still doesn’t make your technique, correct
That's how I proceeded. It was the first water pump repaired by me. I did as I could and as I thought was right.
Salutare, hai sa mai detailam împreună ceva, am mai vazut un sistem de presare, la care folosea o bucsa și presa direct pe camasa exterioară a rulmentului, evita predarea pe bilele rulmentului.
M-am gandit odata ca s-ar putea sa afecteze rulmentul. Dar forta de apasare nu a fost asa mare. Rulmentul a intrat destul de usor in camasa pompei si am zis sa nu mai pierd timpul pentru confectionarea acelei bucse. Corect este cum ziceti dvs. apasarea trebuie facuta pe camasa rulmentului.
Gracias por como enseñarnos a reparar este tipo de bombas.
Me alegro de que este video haya sido útil.
Step socket on the seal is that right?
This is the repair kit. I think I proceeded correctly when assembling the water pump. The water pump is still working.
I have been doing this all day long trying to knock the shaft out of my water pump that is just like that and it will not release. Do you know why?
The hydraulic press is equipped with a 20-ton jack. The bearing came out quite hard. Maybe you should use a degreasing spray or maybe you need to heat the bearing.
@@DorelBorlea I used a 50 ton jack and still cant get it to move at all. I usually don’t have any problems working on my equipment but the water pump is new for me. I have tried everything. I took it to a friends house who had a 20 ton hydraulic jack and they laid a peace of flat iron on the shaft and it never moved, So I went and bought a 50 ton jack and it still didn’t move.
@@tarasizemore6895 there are pumps that have some kind of safety or a pin. You have to remove that pin first and then the bearing will come out.
@@DorelBorlea Do you know where that may be?
@@tarasizemore6895 somewhere on the side of the bearing it should be
please send link store for rebuild kit
You don't press a bearing in by its shaft, you press it in by the OUTER RACE. you likely greatly shortened the life of that bearing by pushing it in via the shaft which is a huge no-no....
The pressing force is not that great. I don't think there will be any problems because of this.
@@DorelBorleaeither way for future reference never press it that way unless you absolutely have to otherwise great video
@@DorelBorleaoh and also you should’ve used some anerobic sealant on the shaft where it goes through the seal
Thank you. I will take your advice into account. I repaired the water pump 4 years ago, I hope I won't need to repair it again soon.
can we rebuild a e34 water pump?
Yes, it can be fixed. You need a repair kit for the water pump e 34 and a hydraulic press.
Minuto 5:00 con eso ya dices lo que sabes de bombas...o sea nada.
:) Naturalmente, no sé mucho sobre bombas de agua. Esta es la primera bomba de agua que reparo. No tienes que hacer lo mismo que yo. Procedí como pensé que era correcto, lo importante es que la bomba esté funcional y siga funcionando.
@@DorelBorlea Suele pasar que se empuja sin querer donde no se debe...
Estaba buscando información sobre cómo reparar una bomba de agua. No encontré mucho. Hice lo que pensé que era correcto. Incluso si empujé el eje central, consideré que no hay riesgo de dañar el rodamiento. El rodamiento entró con bastante facilidad y no resistió.
Part number please