JOIN OUR EXCLUSIVE PROJECT SUPPORT GROUP With WEEKLY GROUP CALLS For Coaching On Farm Equipment Repair, Welding & Metal Fabrication! Its An Affordable, And Easy Skill-Building Program With Only A 1 Month Minimum! Learn About The Program Here: ua-cam.com/video/LbxxZ4l9LnU/v-deo.html Join The Project Support Group Here: www.patreon.com/OWFA/membership
I go around the bolt holes as well. My reasoning is that if you don't it may cause flex or cracking of the housing because its a few thou difference to the mating surface.
You sound about right had to learn that trick from a 70 year old dude that’s been building motors since the 60s been learning slots of tips and tricks building my small block side by side with him check my page out I’m building my 84 cutlass supreme
At 2:45, you mention people waiting for the RTV to become tacky before assembly. Valco Cincinnati's Tech Tips page says, "Silicone needs humidity to cure properly. That’s why Valco advises mechanics to apply silicone and allow it to set for 10 to 15 minutes before assembly. During this time, silicone absorbs moisture out of the air. This permits polymer “cross-linking”- the process that allows silicone to become rubber-like. If parts are put together while silicone is wet/fresh, it is likely the silicone will never set properly."
This is correct.. You must give the silicone access to the air fully before engagement. Anaerobics are usually better when instant installation is necessary.
Though I imagine it's probably a good idea the RTV instructions don't say you need to give time before assembly. They do say to only tighten the bolts finger tight, then tighten fully after one hour and wait 24 hours for full cure.
@@THX..1138 To add to your comment, this is to allow an actual flat gasket to form & set before you torque everything down and squeeze all the RTV out making it too thin and dumping a lot of RTV in the oil; as he states. I have become a certified UA-cam RTV expert lately because I'm about to change the water pump on a 3.5 Duratec (it's under the timing chain cover) and the RTV is what worries me most. Lot's of good vids on YT, but most of them, I've found, only give one piece of the RTV puzzle. This guy is correct, I think, with getting a flat wide bead, but he should really consider letting it set per the instructions; but it sounds like he's had good luck so far.
Letting it "Skin up" before assembly is what some of the manufacturers of the silicon suggest in their instructions. This helps reduce the silicon from getting in the oil or coolant after assembly. Also waiting for the "full cure time", if possible, before filling the coolant or oil will prevent the contamination also. Good video, thanks.
I've found that a coating about the thickness of a piece of paper works well. As stated in the video the surfaces are already very good, so what you really need the silicone for is filling any imperfections. A coating about the thickness of a piece of paper will still have enough to flow into small scratches or imperfections while keeping the joint stronger because the hardware can withstand more pressure than the silicone.
I don't think running it around the outside of the bolt holes is a stupid idea. If the gasket fails at that point, you're have an extra layer of protection.
I have best experience with Toyota FIPG silicone. I’ll used over 13 years only this silicone, great quality and saw it some cars after 10 years still holding great. Just curious brand recommendations to who fight with other brands.
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
Of course the instructions say don't wait for it to tack, but how many do we all know that do wait a bit? Not me, though. I only do exactly what the instructions say. Except I usually don't. And if someone ask me how to do it, I just say, I always do exactly what the instructions say". And then my SO would say, "You're such a liar! I can't believe I let you (beep) me."
I found spreading a thin layer (paint thickness-ish) on one side say the block or diff housing etc. let that set up, skin over. Apply another bead similar to what was shown in the video to the other part(water pump, diff cover etc.) and assemble immediately. IMO and experience it gives a little more thickness to create a "gasket". I have sealed a lot of crap with that method over a lot of years with exceptional results. I also like the ultra grey, the ultra black works well also.
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
Yes, the thin skin first bead is allowed to dry or skin over. It only takes a few minutes, maybe 5 plus. That skin does not squish out from between the parts as readily as uncured rtv. The bead of fresh rtv on the opposing surface fills any small gaps and sticks the two surfaces together. I have seen friends put a bead on one side and let it skin over or not, then assemble with zero leaks and I have also seen it leak, same with my method. I have simply had far better results with my method, so I go with it.@@alexshatner3907
Imo, start with the info the company gives you and then adapt from there. Nobody seems to ever follow the permetex instruction, but perm tells put down the correct amount, put pieces together - finger tight, and then torque 24 hours later. I try to adhere to the time requirements specified, but most do not. I get why, being the time needed before you torque, but apparently it works anyway. You got the one guy here that first puts down a thin layer, let's it tack up, and then does the other side the real way. I would think you want a one layer seel. I've worked with a lot of glue type product in construction, waterproofing, included. All as technical support. Never had one fair on a job I teched. If putting on two sides, you want a monolithic seal, as if it was one piece when cured. I do not believe permetex was designed to do that, but if layer 2 "melts" layer one and they bond as one, theoretically, it could be possible. But in that case, why wait for one side to tack up, as it's not "just" a glue, but I've always treated it as if it creates a gasket itself that you torque down. I guess the stuff sounds like it's pretty screw up proof once you come up with a workable system. I prefer yhe mfgrs system. I'm not gonna be in a rush, and they've already proved it out. But then, if a reliable mech is doing his way, chances he's not getting leaks either. Do overs cost much more than one and done. Clean is always the biggest factor, I have always concerned myself with. Good luck. Hope it turned out well for you. I'm starting one in about 20 minutes. Oil pan farm equipment for a neighbor.
@@nothankyou5524 Sweet, you do you, im sure it works fantastic. I don't have time to wait 24 hrs normally, most mechanics don't. I know my method works, I have my theories behind why it does work and after 25 plus years, see no reason to change what works. Have a fantastic day and hope your neighbors pan turns out amazing.
I do similar. I either tilt tube in so thin rtv is in and thicker near outside edge ...or run finger on inner edge to thin inside edge and maybe push some outward. Hard to explain in words.
Can this be used in marine conditions? I want to use it in my trolling motor(Motor Guide) steering unit. The unit is not in the water. Water splashes on it. I fish only in salt water.
Every time I did the oil pan it would leak if… I didn’t put a thick bead, tighten it by hand until it started to ooze out, wait an hour and then torque to spec. I tried to take different shortcuts including yours, but I ended up repeating the job. Whomp whomp. Lol
Yeah I did that this time. Thick bead, hand tight till it oozed a bit, waited an hour, tightened it down, and its been several hours now. I might just go fill it up.
Awesome video, I think they reason the instructions state to let it cure and then tighten is so that excess rtv doesn't squish too much, but even finger tight it will still moosh out a bit anyways so probably fine either way.
Not sure about this silicone but doesnt say that on the black stuff. It says assemble immediately and finger tighten bolts then torque to spec in an hour.
The Right Stuff says thick bead, hand tight immediately, wait an hour, tighten down, wait 90 mins. Fill her up. I waited a few mins before hand tightening, and a bit extra before filling, but other than that I did the exact directions. We'll see how it goes.
There is one instance for a heavy bead of RTV....small block chevy intakes. Throw away the rubber strip gaskets that go on the block and lay a nice thick bead. Drop the intake on, torque it properly, leave it set for 24 hrs. It will never blow out like the rubber ones.
@@philliphall5198 Aaaww.... you took me back to 1968 with that one! I used to lay up top in my bunk bed thinking that, _if I "grind down" the top of my cylinder head on my Faux Sears _*_Mini-Bike_*_ i'd get increased compression._ Because so much shlit has happened since I seen *Hippies* smokin' pot at Haight & Ashbury, I forgot what i finally did.
It’s not a wife’s tale , the manufacturers suggest it . A 1/8” shallow silicone bead is sufficient . Anaerobic sealant also works very well on flat surfaces .
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
@@alexshatner3907 It is ok to apply and tighten immediately . Before applying clean surface well with brake clean or ether to remove any oil residue on the mating surfaces .
When I do an application of permatex black silicone, (we call it Wally Sauce)not ultra black (that shtuff never cures). I first clean the surfaces with alcohol and then I take my gloved finger and scrub into the surface until I’m sure it’s sticking to it well, then I apply the sauce to workpiece, as demonstrated in this approved video of instruction. Good production thank you
I actually followed the directions where it said to bolt the part loose and then tighten fasteners all the way and my seal failed 😢. This video is 💯 percent accurate!!!!
The reason your hand shakes is due to the fact you're squeezing the tube to push the product out. The simple muscle contraction of your hand won't allow for a completely smooth application. The added approach of going around the bolt holes is simply a good idea to have a uniform layer of sealant on the mating surface.
Man I did it exactly like you did, but… anybody can say me htf can spare the parts then? I’m using a cutter blade but… man it feels like I’m cutting the aluminum. I just put some w40 around the pump and looking for help in the internet
I had a 92 ford ranger 4 cylinder lose oil pressure. Dropped the pan to find the oil pickup completely blocked with chunks of rtv. Engine had never been worked on. It came like this from the factory. Of course it was out of warranty.
I know in 99% of cases this does not apply but..... Somewhere some idiot is watching this video before doing an intake and applying a thin bead to the "China wall" of an intake. When you have two flat surfaces that meet you should apply a thin bead as you have shown as any extra will be squeezed out both sides and can potentially clog hydraulic lifters, oil pressure bypass valves etc. However on surfaces that by design will have a gap its crucial that the width of the bead exceeds the compressed dimension of the gap when torqued. Also in these types of gaps its crucial that both surfaces be completely clean to insure that the sealant bonds to the surfaces and does not leak.
That doesn't work well on autos on that part the new style has a recessed Grove the traps the rtv , that part will scruch it to .010 and seap most times ,others have a high spot that holds it apart farther , you can do that with a tooth pick rtv ed on let dry then set rtv it and it has sufficient thickness
You put on too much silicone! Screw on the applicator tip, cut the tip so that only a thin bead comes out, and then take your finger and dab it so that little hills and valleys are formed and that's it. Like you said, most people put on too much silicone. The manufacturers of small engines make a video showing how little silicone is really needed.
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
Hey I found your channel yesterday and I watched a ton of your old videos. Great stuff! Is this video and some other recent ones current or from a long time ago? Do you still make new videos or no?
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
Don’t listen to the guy that tells you not to wait. Sealants need AIR to cure. This is the reason they recommend giving it the amount of time they engineered it for.
Never use silicone ever ( find something else ) or only use it outside and then wash everything if you are going to do any spray painting or finishing in your shop. Silicone, somehow, gets everywhere and wreaks havoc with paint and finishes by causing fish eyes. Once it's in your shop it takes years to finally get rid of it.
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
The key thing about silicone sealant is never ever ever use it on a gasket it will turn the gasket too mush in a few months then you'll have a bigger problem, supposed to be used without gasket but can be used with rubber o-rings
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
Use anaerobic flange sealant on water pumps. RTV / Silicon causes more problems than it solves. RTV curing is not “an old wives tail.” It needs oxygen to cure. Once you torque the mating surfaces together, the RTV only cures around the edges. I’ve pulled water pumps, oil pans, timing covers…. That have been in place for years and the RTV was still fluid in the center.
Naw I never have. Never get leaks either. I use a caulking gun w a 14oz tube of ultra grey. When you think you have enough, it's usually too much. Most peoples use way too much! Everything that squishes out is wasted. A 3/16" bead is plenty for most applications. Lifelong mechanic by trade specializing in trans & drive lines.
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
@@alexshatner3907 The thing that no one seems to under stand is, Let it skin over like the instructions say. A half an hour or 10 minutes or so. Then put it together. If you put it together wet, it will all squish out. He put on way too much. A thin film is all you need. Thin. Like paint thin. :)
I have a 2008 Cadillac Escalade ESV. GM, nor anyone else (fel-prone,etc.) makes a gasket for the thermostat housing to the water pump. I've wasted so much coolant after putting on the water pump thinking that maybe my tourque specifications were off or something along those lines, when in all actuality, there was a gasket "missing" the whole time that no one makes.This video just saved me tons of money.
@@kellismith4329 Acetone and lacquer thinner are excellent. Residue free contact cleaner is a good substitute in a pinch but it's expensive in comparison to the first two. Best wishes! - Max Giganteum
They can be insulted though, that's ok, I have faith that they can be insulted and are big enough and strong enough to cope. The world will still spin, and carry on.
So you think that you do one job / part right, but you don't do what the label says about letting it dry before adding coolent, because you are mechanic, well to me i would rather use a little to much than not enough, i have done it both ways, and prefer to use a little more for a job, not real messy , but at least twice what he put down,
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
JOIN OUR EXCLUSIVE PROJECT SUPPORT GROUP With WEEKLY GROUP CALLS For Coaching On Farm Equipment Repair, Welding & Metal Fabrication! Its An Affordable, And Easy Skill-Building Program With Only A 1 Month Minimum!
Learn About The Program Here: ua-cam.com/video/LbxxZ4l9LnU/v-deo.html
Join The Project Support Group Here: www.patreon.com/OWFA/membership
I go around the bolt holes as well. My reasoning is that if you don't it may cause flex or cracking of the housing because its a few thou difference to the mating surface.
You sound about right had to learn that trick from a 70 year old dude that’s been building motors since the 60s been learning slots of tips and tricks building my small block side by side with him check my page out I’m building my 84 cutlass supreme
🤔
At 2:45, you mention people waiting for the RTV to become tacky before assembly. Valco Cincinnati's Tech Tips page says, "Silicone needs humidity to cure properly. That’s why Valco advises mechanics to apply silicone and allow it to set for 10 to 15 minutes before assembly. During this time, silicone absorbs moisture out of the air. This permits polymer “cross-linking”- the process that allows silicone to become rubber-like. If parts are put together while silicone is wet/fresh, it is likely the silicone will never set properly."
I think this process will naturally happen to at least some degree in a lot of cases
This is correct.. You must give the silicone access to the air fully before engagement. Anaerobics are usually better when instant installation is necessary.
Though I imagine it's probably a good idea the RTV instructions don't say you need to give time before assembly. They do say to only tighten the bolts finger tight, then tighten fully after one hour and wait 24 hours for full cure.
@@THX..1138 To add to your comment, this is to allow an actual flat gasket to form & set before you torque everything down and squeeze all the RTV out making it too thin and dumping a lot of RTV in the oil; as he states. I have become a certified UA-cam RTV expert lately because I'm about to change the water pump on a 3.5 Duratec (it's under the timing chain cover) and the RTV is what worries me most. Lot's of good vids on YT, but most of them, I've found, only give one piece of the RTV puzzle. This guy is correct, I think, with getting a flat wide bead, but he should really consider letting it set per the instructions; but it sounds like he's had good luck so far.
Letting it "Skin up" before assembly is what some of the manufacturers of the silicon suggest in their instructions. This helps reduce the silicon from getting in the oil or coolant after assembly. Also waiting for the "full cure time", if possible, before filling the coolant or oil will prevent the contamination also. Good video, thanks.
I've found that a coating about the thickness of a piece of paper works well. As stated in the video the surfaces are already very good, so what you really need the silicone for is filling any imperfections. A coating about the thickness of a piece of paper will still have enough to flow into small scratches or imperfections while keeping the joint stronger because the hardware can withstand more pressure than the silicone.
Agree
I don't think running it around the outside of the bolt holes is a stupid idea. If the gasket fails at that point, you're have an extra layer of protection.
It will just leak through the bolt hole.
@@pingpong9656 Rusting the bolt so it snaps on removal. Small Block Ford problems
No it doesn’t, it will leak through the bolt hole.
My thought as well , like why else would a water pump that comes with a gasket also goes around bolts
@@1pyroace1 actually you’ve got a point
Put a plastic bag over tube and put cap on to save the silicone for next job
All I use is this and right stuff on air cooled engines
I have best experience with Toyota FIPG silicone. I’ll used over 13 years only this silicone, great quality and saw it some cars after 10 years still holding great. Just curious brand recommendations to who fight with other brands.
I like the Gray RTV also. It's stiffer when dry. It holds up well when exposed to Hot Oil, even if it's submerged in a hot oil pan in my experience.
i use only red rtv it seems to be stronger
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
@@alexshatner3907 Sort of Wet. Let it set up for about 5 minutes. For a water pump as shown here, you shouldn't need a very thick amount.
Of course the instructions say don't wait for it to tack, but how many do we all know that do wait a bit?
Not me, though. I only do exactly what the instructions say. Except I usually don't. And if someone ask me how to do it, I just say, I always do exactly what the instructions say". And then my SO would say, "You're such a liar! I can't believe I let you (beep) me."
This truly is the best way to do it
When you tighten the bolts down, however much sealer squeezes out that you can see on the outside, is the same on the inside. The less, the better.
I found spreading a thin layer (paint thickness-ish) on one side say the block or diff housing etc. let that set up, skin over. Apply another bead similar to what was shown in the video to the other part(water pump, diff cover etc.) and assemble immediately. IMO and experience it gives a little more thickness to create a "gasket". I have sealed a lot of crap with that method over a lot of years with exceptional results. I also like the ultra grey, the ultra black works well also.
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
Yes, the thin skin first bead is allowed to dry or skin over. It only takes a few minutes, maybe 5 plus. That skin does not squish out from between the parts as readily as uncured rtv. The bead of fresh rtv on the opposing surface fills any small gaps and sticks the two surfaces together. I have seen friends put a bead on one side and let it skin over or not, then assemble with zero leaks and I have also seen it leak, same with my method. I have simply had far better results with my method, so I go with it.@@alexshatner3907
Imo, start with the info the company gives you and then adapt from there. Nobody seems to ever follow the permetex instruction, but perm tells put down the correct amount, put pieces together - finger tight, and then torque 24 hours later. I try to adhere to the time requirements specified, but most do not. I get why, being the time needed before you torque, but apparently it works anyway. You got the one guy here that first puts down a thin layer, let's it tack up, and then does the other side the real way. I would think you want a one layer seel.
I've worked with a lot of glue type product in construction, waterproofing, included. All as technical support. Never had one fair on a job I teched. If putting on two sides, you want a monolithic seal, as if it was one piece when cured. I do not believe permetex was designed to do that, but if layer 2 "melts" layer one and they bond as one, theoretically, it could be possible. But in that case, why wait for one side to tack up, as it's not "just" a glue, but I've always treated it as if it creates a gasket itself that you torque down. I guess the stuff sounds like it's pretty screw up proof once you come up with a workable system. I prefer yhe mfgrs system. I'm not gonna be in a rush, and they've already proved it out. But then, if a reliable mech is doing his way, chances he's not getting leaks either. Do overs cost much more than one and done. Clean is always the biggest factor, I have always concerned myself with. Good luck. Hope it turned out well for you. I'm starting one in about 20 minutes. Oil pan farm equipment for a neighbor.
@@nothankyou5524 Sweet, you do you, im sure it works fantastic. I don't have time to wait 24 hrs normally, most mechanics don't. I know my method works, I have my theories behind why it does work and after 25 plus years, see no reason to change what works. Have a fantastic day and hope your neighbors pan turns out amazing.
Man can you help me on how to spare the parts after doing that? I’m suffering haha
ULTRA BLACK Silicone is the Best.
I do similar. I either tilt tube in so thin rtv is in and thicker near outside edge ...or run finger on inner edge to thin inside edge and maybe push some outward. Hard to explain in words.
Can this be used in marine conditions? I want to use it in my trolling motor(Motor Guide) steering unit. The unit is not in the water. Water splashes on it. I fish only in salt water.
Every time I did the oil pan it would leak if… I didn’t put a thick bead, tighten it by hand until it started to ooze out, wait an hour and then torque to spec. I tried to take different shortcuts including yours, but I ended up repeating the job. Whomp whomp. Lol
Yeah I did that this time. Thick bead, hand tight till it oozed a bit, waited an hour, tightened it down, and its been several hours now. I might just go fill it up.
@@culturebreath369 - Nice… I would wait till the morning if you don’t need to go anywhere tonight. I’m sure it will turn out good regardless.
Thanks legend, I’m in a hurry and need it to work within a cpl hours 😂
Awesome video, I think they reason the instructions state to let it cure and then tighten is so that excess rtv doesn't squish too much, but even finger tight it will still moosh out a bit anyways so probably fine either way.
I also find that especially in tight spaces, slightly cured RTV doesn't wipe away as easily when trying to fit a part.
0:38
In my experience, you should go around the bolt holes
You are supposed to let it sight and tack up because that is what the directions say to do
WATCH THE WHOLE VIDEO!
2:56
Not sure about this silicone but doesnt say that on the black stuff. It says assemble immediately and finger tighten bolts then torque to spec in an hour.
The Right Stuff says thick bead, hand tight immediately, wait an hour, tighten down, wait 90 mins. Fill her up.
I waited a few mins before hand tightening, and a bit extra before filling, but other than that I did the exact directions. We'll see how it goes.
I like to let it set up overnight before I add the fluids and start the engine. don't know if anybody else does this.
I do the same thing. But like he says he's a mechanic and don't have the time to leave it over nite. Sitting cars is sitting money
Let it sit and tack up so it doesn't squeeze out. I much prefer indian head gasket shellac. No squeeze out or contamination of fluids.
R5V IS GREAT . It will seal what needs be sealed. Don't let go where it's not needed .
There is one instance for a heavy bead of RTV....small block chevy intakes. Throw away the rubber strip gaskets that go on the block and lay a nice thick bead. Drop the intake on, torque it properly, leave it set for 24 hrs. It will never blow out like the rubber ones.
I even tuff up surface with electric engraver also and thick layer of right stuff plus wait 24 hours
@@philliphall5198 Aaaww.... you took me back to 1968 with that one! I used to lay up top in my bunk bed thinking that, _if I "grind down" the top of my cylinder head on my Faux Sears _*_Mini-Bike_*_ i'd get increased compression._ Because so much shlit has happened since I seen *Hippies* smokin' pot at Haight & Ashbury, I forgot what i finally did.
How do you clean the surfaces before using RTV?
I've always went around the bolt holes as well. I guess because if you have thru holes & not blind ones, you could have a leak.
I was told to massage a lil bit onto metal surface to make tacky and adhere to the bead layer after.
impressive dexterity
Good old common sense! Good advice and tech advice! I seen globs of rtv size of toothpaste bead! Waste of rtv and messy! Thanks .
It’s not a wife’s tale , the manufacturers suggest it . A 1/8” shallow silicone bead is sufficient . Anaerobic sealant also works very well on flat surfaces .
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
@@alexshatner3907 It is ok to apply and tighten immediately . Before applying clean surface well with brake clean or ether to remove any oil residue on the mating surfaces .
When I do an application of permatex black silicone, (we call it Wally Sauce)not ultra black (that shtuff never cures). I first clean the surfaces with alcohol and then I take my gloved finger and scrub into the surface until I’m sure it’s sticking to it well, then I apply the sauce to workpiece, as demonstrated in this approved video of instruction. Good production thank you
Excellent videos ! 👍
Thanks, nice work!!
I actually followed the directions where it said to bolt the part loose and then tighten fasteners all the way and my seal failed 😢. This video is 💯 percent accurate!!!!
so you made it wrong, cause all fabs are saying the same: bolt it loose, wait, torque it down.
@@oliverroedel1111 doesnt work
@@ronaldwoofer5024 I´m a mechanic, and it works well.
Had a question for you whats your input on using sealant. On heads with head gasket & sealant ?
Yeah i just sent it right away then read directions it says let cure for one hour then torque o well !!
The reason your hand shakes is due to the fact you're squeezing the tube to push the product out. The simple muscle contraction of your hand won't allow for a completely smooth application. The added approach of going around the bolt holes is simply a good idea to have a uniform layer of sealant on the mating surface.
What do you think you taught people exactly? I'm not seeing it
Man I did it exactly like you did, but… anybody can say me htf can spare the parts then? I’m using a cutter blade but… man it feels like I’m cutting the aluminum. I just put some w40 around the pump and looking for help in the internet
I have used RTV silicone without watching this video!!!
Its better to make a paper gasket and paint it.
I had a 92 ford ranger 4 cylinder lose oil pressure. Dropped the pan to find the oil pickup completely blocked with chunks of rtv. Engine had never been worked on. It came like this from the factory. Of course it was out of warranty.
Great tips , thanks
I know in 99% of cases this does not apply but.....
Somewhere some idiot is watching this video before doing an intake and applying a thin bead to the "China wall" of an intake. When you have two flat surfaces that meet you should apply a thin bead as you have shown as any extra will be squeezed out both sides and can potentially clog hydraulic lifters, oil pressure bypass valves etc.
However on surfaces that by design will have a gap its crucial that the width of the bead exceeds the compressed dimension of the gap when torqued. Also in these types of gaps its crucial that both surfaces be completely clean to insure that the sealant bonds to the surfaces and does not leak.
Yes. Use. Nice
You don't have time to let it cure???
That doesn't work well on autos on that part the new style has a recessed Grove the traps the rtv , that part will scruch it to .010 and seap most times ,others have a high spot that holds it apart farther , you can do that with a tooth pick rtv ed on let dry then set rtv it and it has sufficient thickness
Gee i wonder who's wife printed those instructions on most tubes of RTV/liquid gasket and my motorcycle service manual.
Nice
Still using 10 x two much !
Good ol' BOTTOM TEXT
You put on too much silicone! Screw on the applicator tip, cut the tip so that only a thin bead comes out, and then take your finger and dab it so that little hills and valleys are formed and that's it. Like you said, most people put on too much silicone. The manufacturers of small engines make a video showing how little silicone is really needed.
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
Whatever squeezes out is a waste. And you dont want it to "skin" over before torquing the bolts
I love rtv seal. Recently used it to glue the glass panel of an oven door back on
The bigger the glob ,the better the job !
Do ya best silicone the rest
Zetor yeah!
Why people put RTV and with 5-10 minutes?! Because that what the manufacturer tells you on the package!
Guess Im not the only one that read the instructions. Hand tighten then tq however long later.... I think one was 24hrs no?
@@dave-yj9mc Let dry for 1 hr before torquing. Wait 24hrs before filling with fluid.
it doesnt say that on the Black stuff. It says assemble immediately and finger tighten bolts. Torque in an hour.
Hey I found your channel yesterday and I watched a ton of your old videos. Great stuff! Is this video and some other recent ones current or from a long time ago? Do you still make new videos or no?
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
Don’t wait
Don’t listen to the guy that tells you not to wait. Sealants need AIR to cure. This is the reason they recommend giving it the amount of time they engineered it for.
@@kevinanderson8773 Thanks Kevin
I think you should read those instructions before instructing. Or is this a not what to do video.
My Dad did the same
in fact when you bolt it down immediately you waste all silicone. the idea to let it cure for some time is to make a gasket.
yea, no. Doesn't work
Never use silicone ever ( find something else ) or only use it outside and then wash everything if you are going to do any spray painting or finishing in your shop.
Silicone, somehow, gets everywhere and wreaks havoc with paint and finishes by causing fish eyes. Once it's in your shop it takes years to finally get rid of it.
I don't paint I'm more likely to need to use rtv than paint something that is that critical
when you start a job with "..... real quick...."
Ur suppose to finger tackitup.....so it grabs on each mating surface.
Using your finger is stupid because you then create air bubbles in the sealant
Transmission pan bad
2:57 B O T T O M T E X T
That amount was too much also.
BOTTOM TEXT
It's not autistic, it's being thorough.
Never use RTV on anything hydraulic. Thst includes transmissions and power steering.
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
On the directions it says to let sit exposed for x amount of time. 👌🏼
The key thing about silicone sealant is never ever ever use it on a gasket it will turn the gasket too mush in a few months then you'll have a bigger problem, supposed to be used without gasket but can be used with rubber o-rings
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
Use anaerobic flange sealant on water pumps.
RTV / Silicon causes more problems than it solves.
RTV curing is not “an old wives tail.” It needs oxygen to cure. Once you torque the mating surfaces together, the RTV only cures around the edges.
I’ve pulled water pumps, oil pans, timing covers…. That have been in place for years and the RTV was still fluid in the center.
Anaerobic means absence of oxygen. Maybe you should rethink your assertion.
@@kilobravo737probably need to carefully reread what he said lol
The rule that no one follows when using silicone sealant . Always allow the sealant to form a skin before assembly.
Naw I never have. Never get leaks either. I use a caulking gun w a 14oz tube of ultra grey. When you think you have enough, it's usually too much. Most peoples use way too much! Everything that squishes out is wasted. A 3/16" bead is plenty for most applications. Lifelong mechanic by trade specializing in trans & drive lines.
@@oneninerniner3427 You're lucky. Phil's right.
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
@@alexshatner3907 The thing that no one seems to under stand is, Let it skin over like the instructions say. A half an hour or 10 minutes or so. Then put it together.
If you put it together wet, it will all squish out.
He put on way too much. A thin film is all you need. Thin. Like paint thin. :)
@@ebenwaterman5858 Thanks Eben makes more sense the way you explained it
That was a very ugly bead. Should’ve used the nozzle. Like the manufacturer recommends. Also it needs time to cure..
You've never rebuilt an engine because a piece of rtv fell in 😂 stop the cap
You spelled leaked wrong. You spelled it Leacked 😂
For whatever reason I’m autistic 😂
Or just get the correct gasket..,.....,... Never mind, that's another scam 🤣
I have a 2008 Cadillac Escalade ESV. GM, nor anyone else (fel-prone,etc.) makes a gasket for the thermostat housing to the water pump. I've wasted so much coolant after putting on the water pump thinking that maybe my tourque specifications were off or something along those lines, when in all actuality, there was a gasket "missing" the whole time that no one makes.This video just saved me tons of money.
Yeah, apparently no one can make a gasket that doesn't leak.
@@theme61I have same vehicle napa autoparts has that gasket if not get rrv works for me
I wish. Most manufactures are now using RTV at the factory. No actual gaskets are available for those parts.
A little bit goes a Long Way and let it set up before you assemble.
There no dumb reasons.
thanks i will try with valve cover
Now put on a nitrile glove and remove 80% of that. Make it a film, not a layer of icing between two layers of cake.
1 step before anything this guy did is to clean the surface before applying.
Yup, clean it and clean it until you think that it must be clean enough, then clean it some more - acetone seems to work well (ventilate!)
@@kellismith4329 Acetone and lacquer thinner are excellent. Residue free contact cleaner is a good substitute in a pinch but it's expensive in comparison to the first two. Best wishes!
- Max Giganteum
you used to much, not trying to be negative
That's not alot, you should see others 😂
Needs tack off time
Don't say "I'm Autistic" it is insulting to MANY people.
They can be insulted though, that's ok, I have faith that they can be insulted and are big enough and strong enough to cope. The world will still spin, and carry on.
So you think that you do one job / part right, but you don't do what the label says about letting it dry before adding coolent, because you are mechanic, well to me i would rather use a little to much than not enough, i have done it both ways, and prefer to use a little more for a job, not real messy , but at least twice what he put down,
Si I did not quite understand , when you put the bead of silicone are you suppose to wait for it to dry before placing the cover and bolting it down, or do you put it all together, wet and tighten down?
GOOD THING IT DID NOT LEAK. NOT LEACKED
BOTTOM TEXT