Also, your control system is neutral to whatever you are running, so whomever built your system your controls up to that system. It isn’t correlated to all of your machines, it was programmed into your machine system
Good video. I'm glad I found it. Can you explain why one would do this? Maybe an example or your particular circumstance? I ask because I'm getting my very first VMC and it has a Fanuc 0i-MD controller. I'm trying to learn all I can about the controller before I actually cash out for the machine next week. I'm guessing here but it seems like you are connecting some functionality or action to a button on the controller panel. Is that correct? Thanks!
Станок doosan puma gt2600lm fanuc 0i токарный. Есть параметр К0020 в системе, который отвечает за блокировку проворота головы,если например надо работать длинным расточным и он сильно выступает с тыльной стороны. Почему-то не могу сменить бит 0 на 1. Что о блокирует, ключ повернут правильно,смена параметров тоже стоит на цифре 1. Что может ещё блокировать?
Good question. What mill do you have and what year is it? If it is a recent Doosan 2019 - present, the password has been 1976 for a while. You can check with your dealer - if they're cool about it, they'll tell you the password. Otherwise check forums for guys who have a bit of software the crack passwords if you send them your .LAD file. That's what I did. The forum had some dude's email in Bangladesh or something, I emailed him and a week or so later, he emailed me the "1976" password. I'm not sure how he did it, but it worked.
Yep. Whoever designed the UI on this thing should be beaten. It's convoluted and hard to navigate. The good news is that the newer control, iHMI, is better. The machine makes parts well though!
@@ericwhittaker3570 Hi, Do You know how to turn on small "Function Key" window on Actual Position main window? Function Key includes POS PROG OFST CSTM SYS MSG GRAH.
I found out today that hitting the page up or down in any of the areas you get stuck in can often help get to a page you can use to navigate back to where you started- it is frustrating!!
@@fredrezfield1629 I think it's the offset key (press it a few times to get to the right screen, then turn on either MDI or push in the ESTOP, then press 1, then press Input (maybe enter?).
Your “edits” are calling for ‘input/output’ dictated by (y)or (x). Drives are inputs? If I remember and outside sources are outputs(like way lube lines) I’m not familiar enough with code to say what does what on your equipment
How do we address the output bit to a physical location on the board and how do we address the input bit to an m code or button?
Also, your control system is neutral to whatever you are running, so whomever built your system your controls up to that system. It isn’t correlated to all of your machines, it was programmed into your machine system
Thank you. Please send more information about CNC fanuc t6
Sorry buddy, I'm not that much of an expert. ;)
can you help me to create a PMC ladder to the tools changer with fanuc oi-tf
Good video. I'm glad I found it. Can you explain why one would do this? Maybe an example or your particular circumstance? I ask because I'm getting my very first VMC and it has a Fanuc 0i-MD controller. I'm trying to learn all I can about the controller before I actually cash out for the machine next week. I'm guessing here but it seems like you are connecting some functionality or action to a button on the controller panel. Is that correct? Thanks!
On turning center X Y Z axis displays how to repair i
Станок doosan puma gt2600lm fanuc 0i токарный.
Есть параметр К0020 в системе, который отвечает за блокировку проворота головы,если например надо работать длинным расточным и он сильно выступает с тыльной стороны. Почему-то не могу сменить бит 0 на 1. Что о блокирует, ключ повернут правильно,смена параметров тоже стоит на цифре 1.
Что может ещё блокировать?
Nice video sir.. May i know how to enable edit PMC ladder with write protect
Good question. What mill do you have and what year is it? If it is a recent Doosan 2019 - present, the password has been 1976 for a while. You can check with your dealer - if they're cool about it, they'll tell you the password. Otherwise check forums for guys who have a bit of software the crack passwords if you send them your .LAD file. That's what I did. The forum had some dude's email in Bangladesh or something, I emailed him and a week or so later, he emailed me the "1976" password. I'm not sure how he did it, but it worked.
cho mình xin phần mềm fanuc lader 3
Fanuc menu is hard as hell all the time when I pull any button I can not back to main screen.
Yep. Whoever designed the UI on this thing should be beaten. It's convoluted and hard to navigate. The good news is that the newer control, iHMI, is better. The machine makes parts well though!
@@ericwhittaker3570 Hi, Do You know how to turn on small "Function Key" window on Actual Position main window? Function Key includes POS PROG OFST CSTM SYS MSG GRAH.
@@leitzalarm3209 , no, sorry. I'm not sure how to do that.
I found out today that hitting the page up or down in any of the areas you get stuck in can often help get to a page you can use to navigate back to where you started- it is frustrating!!
00:47 i can't get the control to stay in "YES"
any idea?
Check your Estop it needs to be pressed. Usually that does the trick for me.
@@ericwhittaker3570 how do you NORMALLY on a fanuc turn the Write Parameter ON:1 in "SETTINGS" ?
@@fredrezfield1629 I think it's the offset key (press it a few times to get to the right screen, then turn on either MDI or push in the ESTOP, then press 1, then press Input (maybe enter?).
Your “edits” are calling for ‘input/output’ dictated by (y)or (x). Drives are inputs? If I remember and outside sources are outputs(like way lube lines)
I’m not familiar enough with code to say what does what on your equipment
Sir What type of controller
Fanuc Oi.
Sir fanuc controller.lader programming..... Sir controller No.s7 controller or,????
i get password and cant see ladder , how to know password?
I dont understand the meaning of R or A x and y in this kind of programs
r is internal relay. a is message display. x is input signal from the machine to the pmc. y is output signal from the pmc to the machine.
V