I recently made a mitered picture frame, and for the 1st time opted to use dowels to hold the miters together. This is now my preferred technique since it aided with alignment and the joints could not slip during clamping.
You're marvelous teacher. One thing is to know how to do it for yourself, but passing and sharing the knowledge is a completely different level. And you did it exactly that. Thank you.
At this time, we're only selling the gallon size. We hope to offer a smaller size in the future. If you decide to purchase the gallon, we do sell a glue applicator set that will could be helpful: www.rockler.com/rocklers-glue-applicator-set
Yes, both photos shown in the video are rabbeted in the back to recess the glass, photo and backer board. These rabbets can be cut either before the picture frame is assembled (at the router table with a straight bit or piloted rabbeting bit or on a table saw with dado blade) or after it's glued up with a piloted rabbeting bit in a handheld router.
I’m new to woodworking. I thought a picture frame would be something easy to begin with. I only have a mitre box. Would I be better suited to make something easier and if so, what would you suggest that be? Thank you
no glue--- great video but why suggest a glue we can't get. Speed set is not available in the size shown. wasted an hour of my woodworking time searching the web trying to fine it.
We apologize that you were unable to find the glue. At this time, we're only selling the gallon size. We hope to offer a smaller size in the future. If you decide to purchase the gallon, we do sell a glue applicator set that will could be helpful: www.rockler.com/rocklers-glue-applicator-set
Hi John, a miter saw is a fine substitute for a table saw for cutting 45-degree picture frame miters. But be careful to check the saw's cutting angle for accuracy, just as you must do when using a miter gauge on a table saw for the same purpose. Even though a miter saw as a 45-degree detent to help up your odds for accuracy, it still can get thrown off with normal use and wear and tear.
they carry it, but only in the gallon size. It would take me years to go through a gallon of glue. I bought a gallon of Titebond 3 two years ago, and I've only used about a quarter of the bottle. It's honestly probably gone bad at this point.
@@johnh4921 I'm starting to think they just aren't offering if in anything smaller than that right now, because I went directly to Titebond's website and they only offer it by the gallon there too.
i was getting very pissed off with the accuracy. i was using a mitre saw. evolution brand. all squared up and set. the last piece of assembled into place alllllwwys was off. i then tried the rail with Protractor in the dewalt table saw. by taping all 4 pieces of wood togather on a bunch i cut all 4 pieces at once. the whole thing was perfect.
I recently made a mitered picture frame, and for the 1st time opted to use dowels to hold the miters together. This is now my preferred technique since it aided with alignment and the joints could not slip during clamping.
💙
You're marvelous teacher. One thing is to know how to do it for yourself, but passing and sharing the knowledge is a completely different level. And you did it exactly that. Thank you.
Thank you! Glad we can help.
That was the best video I've seen regarding mitered picture frames. Nice job!!
Thanks for watching!
Thanks Chris! I always enjoy your presentations. Very clear instruction.
Thanks for watching!
Most framers grab readymade frames or precut strips and talk do this and do that. This video is very informative
The section on glue was fantastic. Rockler should make another video just about types of glue
Products aside-Chris Marshall seems like a great instructor.
One tool i don't see as much being used is Collins clamps i used them as a finish carpenter.
Exactly the information I needed at this time. Thanks.
Thank you for the tips!
🙌
This is a great video. Thanks so much.
Thank you-very well presented video.
Thank you. Perfect for my 16x20 canvas print applications.
Thanks Chris!
great video, but where can i purchase a small bottle of titebond speed set? i only find the 1 gallon size.
At this time, we're only selling the gallon size. We hope to offer a smaller size in the future. If you decide to purchase the gallon, we do sell a glue applicator set that will could be helpful: www.rockler.com/rocklers-glue-applicator-set
Very good video but did he put a rabbit on the frame to hold the picture?
Yes, both photos shown in the video are rabbeted in the back to recess the glass, photo and backer board. These rabbets can be cut either before the picture frame is assembled (at the router table with a straight bit or piloted rabbeting bit or on a table saw with dado blade) or after it's glued up with a piloted rabbeting bit in a handheld router.
I’m new to woodworking. I thought a picture frame would be something easy to begin with. I only have a mitre box. Would I be better suited to make something easier and if so, what would you suggest that be?
Thank you
Hi Mastiff Mom, Please reach out to our product support team at 1-800-260-9663 or support@rockler.com. They'll be able to assist you. Thank you
no glue--- great video but why suggest a glue we can't get. Speed set is not available in the size shown. wasted an hour of my woodworking time searching the web trying to fine it.
We apologize that you were unable to find the glue. At this time, we're only selling the gallon size. We hope to offer a smaller size in the future. If you decide to purchase the gallon, we do sell a glue applicator set that will could be helpful: www.rockler.com/rocklers-glue-applicator-set
Why not use your miter saw for the 45deg cuts?
Hi John, a miter saw is a fine substitute for a table saw for cutting 45-degree picture frame miters. But be careful to check the saw's cutting angle for accuracy, just as you must do when using a miter gauge on a table saw for the same purpose. Even though a miter saw as a 45-degree detent to help up your odds for accuracy, it still can get thrown off with normal use and wear and tear.
Thanks
Yeah , but how about the rabit? How do you put that into the variable.
Hi there, please reach out to our Product Support team at 1-800-260-9663 or support@rockler.com. They may be able to assist you. Thank you!
So I checked Rockler's web site and they don't even carry the Titebond Speed Set touted in the video. Weird...
they carry it, but only in the gallon size. It would take me years to go through a gallon of glue. I bought a gallon of Titebond 3 two years ago, and I've only used about a quarter of the bottle. It's honestly probably gone bad at this point.
@@joepiz016 Thanks, it didn't show up when I ran a search on the site, not even the gallon. But you're right, I could never use a gallon!
@@johnh4921 I'm starting to think they just aren't offering if in anything smaller than that right now, because I went directly to Titebond's website and they only offer it by the gallon there too.
@@joepiz016 Thanks for the heads up, appreciate it.
i was getting very pissed off with the accuracy. i was using a mitre saw. evolution brand. all squared up and set. the last piece of assembled into place alllllwwys was off. i then tried the rail with Protractor in the dewalt table saw. by taping all 4 pieces of wood togather on a bunch i cut all 4 pieces at once. the whole thing was perfect.
Five tips? Or five products to sell?
This is an edvert, not a tutorial.
What's with this guy, he is so annoying. Rockler surely could find some with more personality
Are you looking for Woodworking tips or a girl friend