Thanks! I have one more thing you might want to check out: a free amp/box construction/wiring app we made called KickerU. Here's the link: www.kicker.com/kickeru
Either 1 or 4 ohms depending on how you wire it. You might want to grab this free app we made called Kicker U: www.kicker.com/kickeru. It gives you wiring instructions, test tones, a wire calculator and much more.
Sorry for the delay! You would be running that amp at 4 ohm stereo. I checked out the specs on that amp and you would be running 200 watts to each voice coil.
Quick question. I'm getting 2 10" L7S's. I have a 1 ohm stable amp. I want to bring them down to one ohm, but my enclosure has 2 seperate chamber so I cant tie them together inside the box. What I'm wondering, is if I tie them on the outside of the box (connecting the 2 terminals on the back of the box, then running only one set of speaker wires to the amp), if it will do the same thing. In my head it works the exact same way but a second opinion and possibly more experienced one can't hurt. Thanks
hello i have 2 12s kicker l7 4 ohms and a kicker 08zx1500.1. my question is how do i wire them to a 2 ohm or will a 1 ohm be good for this amp. thanks.
Hi there how are you? I got 2x L7 15inch 1000RMS 4ohm subs and also a 5000D monoblock amplifier 1ohm. Is that allright to run those 2 sub or it’s gona blow the subs? Cheers
I have a question about wiring subs in parallel with a thick wire? Is it not possible to use anything bigger than 14 or 12g for the jumper wires? I ran into an issue where I could fit two 10g wires in the same terminal.. What should I do? Subs are 4ohm dvc 600rms each. Any help is greatly appreciated!
I have two hfx12d4 dvc n they are 800w maxx n 400 rms i have a 1500w amp n my amp runs700rms at 4 ohms n 1100rms at 2ohms i can not find a way to hook up both of them to my amp at 2ohms please help
ok so i have an audiofonics adf-243 and it says its 4 ohms stable at 2 channels i hooked it up to a dvc 4ohm sub 1 channel to a voice coil and the other channel to the other voice coil thats running at 4 ohm right ?
Hay i wired my subs exactly how u showed and the were hitting unevenly then the voice coil locked up on one of the subs. My subs are db drive k9. They can handle 1ohm and so can my amp. Idk what happened. I need help please. Also started to melt wires goin from amp to sub box. Any help asap would be greatly appreciated. Thanks
i have 2 l5 in enclose pro box i bought a 1000.1 zx not the new model the one that's has little vents or airs holes in the middle can i wire them like this video
Ok I have two 12 inch alpine subs both 4 ohms and I have 1000 watt sony explod will I be able to use it and get more power. If so how will I need to wire it?
I have two Kicker 40CWR124 CompR Series 12 inch Subwoofer 4 Ohm and it has the switch for 2 ohm and 8ohm. I want to run at 1ohm. How do I set up the wires on the speakers for 1ohm? Remember I only have 1 terminal positive and negative on each speaker.
?how would i wire 2 dual vc 4ohm subs to a 4ch amp. I tried to wire it up thinking the coils were 2ohms but it appears that each coil is 4ohm. so i need to wire up 2 subs unfortunately all i have for the subs is a 4ch which can be bridged
how many watts is a kicker 07cvr124, I have 2 they are 4 ohm,going to wire parallel to achieve 2 ohms, how do you connect to a 4 channel amp,that does support 2 ohms
I'm confused, I'm trying to wire 2 10" DVC 4 OHM subs to my 2 channel amp. The amp says I can get the most RMS @ 2 OHM. How do I wire my subs to achieve the 2 OHMs at the amp? My amp doesn't support a 1 OHM load, only 2 and 4 OHM loads. Can some one please help me.
What if I have a Mono Class D amplifier which is a 1ohm stable..do I still run it to one side connection?? Because the car audio who did it hook up both subs to my amplifier as a 1ohm stable.. any help would I would be grateful
Running one side of a sub, while possible with many (but not all) DVC subs, cuts the power handling in half. So the question to ask yourself is this: is the advantage of getting a lower ohm load worth changing the power handling of the sub, and your setup? Usually, no. Bear in mind that doubling the power results, on average, of increasing the output by about 3dB. Most people say that the actual perception of double the volume to the human brain is 10-12dB. At the end of the day, double the power never equals double the volume. Plus, higher ohm loads tend to be more accurate, acoustically speaking. Hope this helps Samuel!
Hey Tyson my amp is rated at 1. 900w x 2 @ 2ohm 2. 550w x 2 @ 4 ohm 3. 200w x 2 @ 8 ohms Can I wire a pair of speakers at 8 0hms and a 2nd pair of speakers at 4 ohms and wire a pair of subs at 2 ohms ??
OK thanks but one more question, I was looking at this bd t1500 amp which is rated to do 1000 watts@4ohms, 1500 watts @2 ohm and 1500 watts rms @1 ohm.would this be a good amp to run on that kicker solo X 18, I was told to get a high out out alt, or gage wires and a heavy duty battery up front, would this b a good set up also...If not I'm willing to spend around $700 or $800 bucks for a amp the bd t1500 is $700 bucks
I have 2x older 2ohm 12" l7's in separate enclosures and a 1000 watt 2 ohm amp... can I wire them to work with this amp ? I nolonger know the model of the L7 so I don't know the rms rating ?...?...?... thank you for your help in advance 🥃cheers🍻
@@KICKER-AUDIO rockford fosgate r1000 1d & kicker solo-baric L7 12 I believe there dual voice coil farily old back wen you guys had the silver accents on the bezzle.
@@KICKER-AUDIO how can I find the molded number of the subs ? I haven't took one out of its enclosures in many many many years 😅 relics of my youth you might say but the new truck got some much needed love this year!
I have 2 15" cvx dvc 4 ohm is 2 way to conect 1 0hm and 4 ohm and I have kicker cx 2500.1 i guess is the line before the zx models but this amp is 2 ohm stable right so I have to wire my subwoofers to 4 di you have a video to see
With a pair of S12L54's you can wire them to either a 4 ohm or 1 ohm configuration. The ZX7501 is is designed to work best at 2 ohms. Ideal situation would be if you could exchange your dual 4's for dual 2's. If this is not possible, one option would be to wire them in a series/parallel configuration and run them to the amp. This would only show the amp a 4 ohm load which would decrease the power from 750+ watts to 375-400 watts. Another option would be to run only a single S12L54 wired in parallel to the amp. This would push 750+ watts to the single sub and you would have to keep all the gains and bass boost down and watch out for overpowering but it's an option. We would not recommend wiring down to 1 ohm as the amp is not stable. It will run at times but not consistently and all the shutting down will eventually cause issues with the amp.
KICKER, i have two 4ohm kicker cvr 10inch subs but my amp gives max performance on 2ohm... how do i correctly run my wires? or do you have a video that explains that already? please help! Thanks... Great videos by the way, tons of info to the rookies like me!
Red with white dots white with black dots black dots with solid red. Red with white dots. Solid white with red dots. See. It’s simple. Was the red with white dots negative or positive. The solid red means power the white stripes mean ground. Camera was too far away couldn’t see these stripes and solid dots or a overhead view would have been perfect. As much as I’d like to say this video helped, I’m going to have to watch another video. This one left a little something to be desired. But seriously. Red to red. Black to black on each speaker. Then run 1 set to the amp. Right?
I have 2x 07CVR124's, what wattage amp should I buy?? What should i look for? Ive read around a bit but I have found many different answers. Also what guage sound wire should I use for the best sound? Should I wire them the way you did up above? Forgive my noob questions, I am prepared to learn though ;) Thank you, looking forward to hearing back :)
The RMS is 400 watts per sub, so you're looking for about 800 watts total at 4 ohms (you'll want to wire them series parallel). This is the best one: www.kicker.com/44KXA16001
i ended up wiring the - to - and then the + to + on each speaker individually, then choosing one - and + from each speaker and putting it to its own output from the amp instead of wiring the speakers together.
This video is for a different ohm load sub, but it does show you how to wire in series parallel and how to check that with a meter. I've bookmarked the video to start with how to check your final ohm load: ua-cam.com/video/htx0aXmzFmo/v-deo.htmlm24s
Question: I have 2 speaker inputs on my 1 ohm stable massive n2 amp.. do I wire like he did . And just use the one side of the terminals on amp. I believe they are bridged to make 1 ohm inside the amp ..please clarify
Sorry, never heard of "N2". If they set up their terminals like we do on our amps, the 2 pairs of terminals are mainly there for convenience, so you dont have to jam too much wire into your sub's terminals. Just to be safe, please check with Massive and verify that is the case. They may have that info on their manual as well.
Hey I have kicker solo X 18 and I was wondering could I power that speaker with a amp that pushes out 1500 or 2000 rms with no problem? Oh and I how would I know if it's a 2 or 4 ohm coil....I guess it would b a 4 ohm by it having 2 positive and 2 negative coils rite? I'm kinda new to the audio world
Hey Kevin - the S18X can handle the 1500 -2000 watts without a problem. Make sure the other settings on the amp like the gain and bass boost are set at the right levels to be compatible with your headunit. We made that speaker in both a dual 2 ohm and a dual 4 ohm version so it could be either. If there is not a sticker or anything on it to tell you what the ohm is you will need to test each coil on an ohm meter to see what it reads. If it's a dual 2 then each voice coil should read a little less than 2 and the dual 4 ohm will read a little less than 4.
Just out of curiosity if I have 2 terminal ports on my box could I run both subs out to the box and then run both to the amp so that the power goes through both subs quicker so that it's not running through one sub and then to the next. I have 2 kicker l7s and a hiphonics 2400 monoblock amp thanks...
One thing to keep in mind is that the L7's are dual voice coil, so if you want to connect them to terminals, you will be changing the ohm load you can deliver. Granted, you would end up doing that anyway, whether it was from the terminals or not. As long as the new ohm load works with your amp, then there's no harm in doing that.
Oh and I was also told the speaker is 10,000 watts and 5,000 rms or 3,000 rms idk, so would 1500 watts rms hurt that speaker by under powering it? I been told alot of different story's idk what to believe that's why I'm asking u Mr kicker...oh and it's a 4th speaker so I'm a get it wired down to 2ohm
Originally this speaker was designed for SPL competitions, It is able to handle 5000-10000 watts peak but only recommended for those 20 second bursts to get the top reading. When people began using them in their everyday systems, we explained that for continuous music, the RMS value would be around 2000-3000 watts. The different power handlings are based on the type and size enclosure you are using. Do you have your box information?
hello I need help I have two low kicker L7 of 12 inches 750rms I am moving them with a boss power phantom of 5000 watts but they tell me that they do not hit much. I want to know if you recommend switching power? urgent help ¡¡¡¡
There could be many issues. The wiring could be incorrect, the power insufficient, or there could be a technical problem with the amplifier or subwoofers. I would suggest one of two things to do next: either bring the stereo back to the shop that installed it and let them diagnose the issue(s), or call our Technical Support department. They are open weekdays from 8-5c at 405-624-8510. Thanks!
You're diagram is different from what you said, jointing the 2 speakers you said black to red and black to red. Diagram shows red to red and black to black
No I don't have my box information cus I bought the speaker in a built box 2nd hand about 4 years ago, so Idk where the guy is now to ask that question, all I know that the speaker works,so if I put a good 1,500 or 2,000 rms amp on it, with a high output alternator,0 gauge wire and a good big battery up front would this be ok? Cup I'm not trying to push them at 3,000 rms...would the bd t1500 or the zx 2500.1 work also
Does it have to be the white dots to the amp or can it be the other way around or mixed up but still be + to + .... - to - Ex: the ones that lead to the box terminal... can it be a (+ w/ ○) & (solid -) ?
With some amps, the lower the ohm load, the higher the power rating. We recommend you match the RMS of the amp (at that ohm load) to the RMS of the sub(s). Please check how low the load can be for your amp. It varies by manufacturer.
Ok I have a quick ? So I have two dvc 12in l5s that are 4ohm and a dvc 12in cvr 2ohm sub and I was wondering if I could wire these all together on my sound ordanace 1500m amp?
Couple of things - you don't want to mix the same size subs that are different models. The sound difference when they play would muddy the sound and it won't be good. You could cross them over at different points but it's still not something we would recommend. Next the dvc 2 ohm speaker would see a different amount of power then the dvc 4 ohm subs due to the resistance of the voice coils. The M-1500 is rated at 500 watts RMS at 2 ohms or 300 watts at 4 ohms. Unfortunately this will not work with the pair of L5's because you would only be able to wire them into a 1 ohm or 4 ohm load to the amp. You could run either a single S12L54 wired in parallel to the amp and it would see 500 watts or you could run the CVR122 in series to the amp and it will see 300 watts. Hope this helps.
How do I find the ohm load to my amp? It's a 1600 pioneer champion series 2ch... And I got 2 L7 10" subs with a 4 gauge amp kit 125a in line fuse 3farad vm audio capacitor ...
Best way to find the details of your Pioneer amp is to check their website, usually in the tech support area. Find the instructions, and the ohm load tolerances should be printed there. The model number should be on the amp somewhere.
I got two 1500w 4ohm duals and a 2ohm 5000w two channel amp. What would be the best way to wire them for maximum performance?? Do I have to bridge the amp??😕
I was always curious about the hole that gets drilled in the divider. If it makes a difference in sound quality. This is the first time I've heard anyone say one way or another if it makes a difference in the sound of your subs.
Brandon Burks That small of a hole to run your wires thru will not cause a sound difference. We normally recommend each sub having it's own air space. We feel like each speaker can perform better and if something happens and one blows, the other is not working in twice it's recommend air space and can blow easily.
+KICKER Is it possible/recommended to connect each woofer to the terminals and run the jumpers between the terminals? Rather than drill holes and run the jumpers from speaker to speaker.
Sonif I have a 2500.1 soundstream and. 2 audiopipe 15s it's best to run them not togather in parallel for 10hm instead run the separate positive to postive neg to neg to the run 4 wires from the mono block
Some enclosures have a single set of terminals, some have more. You need to know the ohm load of the terminals (check with a multimeter) to determine how to wire them to the amp. Tech Support's contact info is: support@kicker.com or 405-624-8510. They are open weekdays 8-5 CST. They can help you wire it correctly.
My amplifier is 2Ω stable and 40 bridged. My subs are 40 per sub now. Their 40 DVC. I want to bridge my amplifier 40 mono bridged. Do I wire them together to get a final impedance of 40 Thank you. Im looking to get the maximum power.
2 ohms stereo and 4 ohms bridged usually gives you the exact same amount of power, so you're fine either way. You can follow the directions in this video to give you 4 ohms bridged. You can also go to this link to grab our free app, Kicker U. it has wiring diagrams, box building info, tuning info and much more. www.kicker.com/kickeru
Sooo can this be achieved by wiring red to red and black to black and running them on a bridged channel on a monoblock amp? Or can i do red to red and black to black and run each sub to their own channel
Amp is a fusion powerplant pp-am200010 2000w class d mono block soo to clarify... do i wanna doneach sub red to red and black to black and go to each channel.... or wire them together like this.... and go off of one channel
Unfortunately the math doesn't work out on that. You can do 1 or 4 ohms with those subs. Since you have a mono amp, they probably designed the 2 sets of inputs as a matter of convenience during setup. It's still one channel as far as the amp is concerned (unlike a stereo amp, where each set of inputs is independent). We made a free app to make wiring and tuning easier. You might want to check it out: www.kicker.com/kickeru
@@KICKER-AUDIOI wired them sending negative to the other negative on the other sub, same with positive and ran them out to the amp, is that right? Ty for your response
Do i have to jump 1 sub to the other or can i just have 1 sub qired to a 2 ohm load and other sub at 2ohm load then i have 2 positives and to negs can i run both positives and both negatives to the amp and still get 1 ohm load or do i hav to jump 1 sub to the other. Or is that just a way to get more power?
Jeremiah hodge You always have to have positives and negative’s connected for every speaker. As far as the amplifier connection, some amplifiers are one ohm stable and some are not. You would have to check your app to make sure it’s capable of that load.
KICKER what i am saying is i have 2 12 L7s 4ohmdvc and a 2 12 box with a divider if i run one sub to 2 ohms and the same with the other sub. I have 2 terminal caps that leaves me with a positive and negative on 1 side and same for other side. When i hook both of those to the amp will i still get a 1ohm load i have a 1200.1 kx my manual says 1 ohm stable. But the way the video shows it has one sub ran to the other sub and then lwft with just 2 wires. Is that a better way or the only way i will get a 1 ohm load my amp is like 15 years old. When best buy started selling kicker? I already blew up a 1250.1sdx because i ordered a 1200.1 kx offline and they sent me the sdx model and manual that came with it said 1 ohm stable but when i looked recently it says 2 ohm stable online. The lil digital screen just says service. But i was past warranty. I still have the sdx.
On our mono amps, we have two sets of terminals to make wiring easier. What you will do is attach each wire from each terminal cup to the amp. This will result in a 1 ohm load. It is effectively the same as twisting each + wire together and each - wire together, like you used to do on a mono amp with just one set of positive and negative terminals.
One other note. I just learned that we do still repair that amp. The charge generally ranges from 75-125 depending on the issue. If you contact customer service they can give you the details, assuming you want to repair the amp. The number is 405-624-8510. Open weekdays from 9-5 central time.
I have 3 dual 4 ohm subwoofers I wire them down to to 2ohm and I wired all three together and I get .5ohm well I need an amp that is a half stapled or will 1ohm do
You would need an amp that is .5 ohm stable. Most amps that were 1 ohm stable would play at .5 ohms but you would not be able to turn up the volume and over time it would work the components harder and cause them to fail quicker.
Different ohm loads exist to get the most out of the amp you're using, and/or to let you use the number of subs you need to create your system. All of the subs of a given series and size have the same specs, whether they are 1, 2 or 4 ohms. Make sense?
They reco.end that for casual liatening. If u r goin to be pushin em hard juat use 8guage . it keeps the heat down and u dont hav to qry about what brand wire you r using trust. Ive been threw about 16 dif L7s since 1gens. U want best currsnt possible. Always remeber they want u to buy more. Thats y they quit the solo x's cuz u could fix you're self
Devante Mccoy You will want to do a series/parallel configuration. Wire each dual 2 ohm sub in series, then you will parallel them together and this will give you a 2 ohm load.
I found the specs on the bex-2150-1d, and it said it was 1 ohm stable. If that's the same amp, then you're good. I'd go to the hifonics website to confirm if I were in your shoes, or contact them directly.
KICKER i burnt one of my subs i just want to see if you would know why so i wont burn another one sorry im just new to this i was thinking because i was messing with the bass test tone trying different hz to get my gain from my amplifier
There are several things that can lead to a subwoofer failing. Sometimes its the sub, sometimes its the amp, sometimes its the tuning or install. We can help you diagnose the problem if you give us a call. Tech Support's number is 405-624-8510, and they are open weekdays from 8-5 central time. They're happy to walk you through it, so you can tweak your system.
You can use the wiring wizard in Kicker U (www.kicker.com/kickeru) for wiring diagrams if you like, but unfortunately 1 ohm isn't possible with a pair of 2 ohm DVC subs. 2 ohms would be the lowest, unless your amp is 1/2 ohm stable.
I've been looking for help on a setup I'm putting together I have 8 15" 1000 to 2000 rms range subs they are split between two 4000 watt mono amps so 4 to each amp I know I can only go as low as 2ohm to each amp they are wired and working but I just want to know what's the best wiring setup my box dimensions are 32" wide by 64" long and15" high sealed in a 94 geo prizm double 20 farad caps double alternator and double battery I know what im doing just not in the sub wiring dept
Adam Corte Not a problem! You are going to do a wiring configuration that includes both series and parallel. For each set of 4 woofers, wire each dual 4 in series. This will create 4 x 8 ohm woofers. Then you will wire all four in parallel to create a 2 ohm load to the amp. Hope this helps. If you have further questions just let us know.
Thank you guys so much for helping me wire my subwoofers! my next purchase will definitely be from kicker!
P]⁰
Easily explained finally wow thanks brother 🙏 all that drawing and 30 minute videos what a waste of time and confusing hands on showing is awesome 👌
Thanks you go straight to the point with no bs great job
Thanks! I have one more thing you might want to check out: a free amp/box construction/wiring app we made called KickerU. Here's the link: www.kicker.com/kickeru
If you do that you will be wiring the voice coils in series and that makes the dual 4 ohm sub an 8 ohm speaker.
switched them and the 2 Ohm 12" Kicker Comp D sounds hella good! and at a great price too!
Awesome thank you. I've watched 20+ videos and needed to know if I can use the non jumper side to run to the amp. Thanks again.
That is correct!
I just by me a DX 1000.1 & one 15" L7 2 ohm how can I wire this? please help
two s12L7 4 ohm in amp zx1500.1 how connected.. parallel/serie-parallel?
KICKER I have 4 subwoofer all 4 are dual 2ohm if wire all 4 what will I get
Either 1 or 4 ohms depending on how you wire it. You might want to grab this free app we made called Kicker U: www.kicker.com/kickeru. It gives you wiring instructions, test tones, a wire calculator and much more.
The ZX1500.1 is rated for 2 ohms mono, so if you have two 4 ohm speakers, 2 ohms will deliver the most power. You'd wire in parallel for that.
Sorry for the delay! You would be running that amp at 4 ohm stereo. I checked out the specs on that amp and you would be running 200 watts to each voice coil.
Your A Lifesaver
You don’t have to drill a hole through the divider you just connect them together straight to the amplifier and it I’ll do it’s job
Thanks broo best speakers everrr OMGG
Quick question. I'm getting 2 10" L7S's. I have a 1 ohm stable amp. I want to bring them down to one ohm, but my enclosure has 2 seperate chamber so I cant tie them together inside the box. What I'm wondering, is if I tie them on the outside of the box (connecting the 2 terminals on the back of the box, then running only one set of speaker wires to the amp), if it will do the same thing. In my head it works the exact same way but a second opinion and possibly more experienced one can't hurt. Thanks
i wired my kicker cvxs exactly like that but i didnt notice the dots.. do i need to re wire
hello i have 2 12s kicker l7 4 ohms and a kicker 08zx1500.1. my question is how do i wire them to a 2 ohm or will a 1 ohm be good for this amp. thanks.
for a set of kickers l7s dual 4 ohm 700 watts rms 1500 max power each what amp do i need if i want the most out of them?
a CT SOUNDS 1400.1 amp with two L7 12's 4 ohm each. ? help should i run 1 ohm or 2 ohms to the amp? im confused
I got mine from someone and missing the wires. Where do I get the wires?
Hi there how are you? I got 2x L7 15inch 1000RMS 4ohm subs and also a 5000D monoblock amplifier 1ohm. Is that allright to run those 2 sub or it’s gona blow the subs? Cheers
I have a question about wiring subs in parallel with a thick wire? Is it not possible to use anything bigger than 14 or 12g for the jumper wires? I ran into an issue where I could fit two 10g wires in the same terminal.. What should I do? Subs are 4ohm dvc 600rms each. Any help is greatly appreciated!
I have two hfx12d4 dvc n they are 800w maxx n 400 rms i have a 1500w amp n my amp runs700rms at 4 ohms n 1100rms at 2ohms i can not find a way to hook up both of them to my amp at 2ohms please help
ok so i have an audiofonics adf-243 and it says its 4 ohms stable at 2 channels i hooked it up to a dvc 4ohm sub 1 channel to a voice coil and the other channel to the other voice coil thats running at 4 ohm right ?
Hay i wired my subs exactly how u showed and the were hitting unevenly then the voice coil locked up on one of the subs. My subs are db drive k9. They can handle 1ohm and so can my amp. Idk what happened. I need help please. Also started to melt wires goin from amp to sub box. Any help asap would be greatly appreciated.
Thanks
i have 2 l5 in enclose pro box i bought a 1000.1 zx not the new model the one that's has little vents or airs holes in the middle can i wire them like this video
Ok I have two 12 inch alpine subs both 4 ohms and I have 1000 watt sony explod will I be able to use it and get more power. If so how will I need to wire it?
hi I want to know how to wire nd conect I got 2 kicker l7s 12s nd 2012 1500.1 kicker amp small chasis I want to know how I can do it
I have two Kicker 40CWR124 CompR Series 12 inch Subwoofer 4 Ohm and it has the switch for 2 ohm and 8ohm. I want to run at 1ohm. How do I set up the wires on the speakers for 1ohm?
Remember I only have 1 terminal positive and negative on each speaker.
does it matter with the dots like if i run red dot to solid red.. or if u use the solid red and dot black to amp??
?how would i wire 2 dual vc 4ohm subs to a 4ch amp. I tried to wire it up thinking the coils were 2ohms but it appears that each coil is 4ohm. so i need to wire up 2 subs unfortunately all i have for the subs is a 4ch which can be bridged
Thanks this helped alot
Can all dvc 4 ohms go down too one ohm or does it matter
how many watts is a kicker 07cvr124, I have 2 they are 4 ohm,going to wire parallel to achieve 2 ohms, how do you connect to a 4 channel amp,that does support 2 ohms
un bridge it ? bc if I'm right 1 ohm would be pilling a even greater amount than a 2 ohm bridged can pull
I'm confused, I'm trying to wire 2 10" DVC 4 OHM subs to my 2 channel amp. The amp says I can get the most RMS @ 2 OHM. How do I wire my subs to achieve the 2 OHMs at the amp? My amp doesn't support a 1 OHM load, only 2 and 4 OHM loads. Can some one please help me.
WHAT WOULD BE THE BEST AMP FOR THIS SET UP?
I have a BAMF 5,5000 class d mono block amp and I have 2 L7 15 inch subs how can I wire them to get the most bang out of them ? Please help
I have 2 kicker cvr 12s 4ohm running to a kicker zx1000.1 ported box is this a good wireing for me .thanks
What guage wire are you using to jump
What if I have a Mono Class D amplifier which is a 1ohm stable..do I still run it to one side connection?? Because the car audio who did it hook up both subs to my amplifier as a 1ohm stable.. any help would I would be grateful
Running one side of a sub, while possible with many (but not all) DVC subs, cuts the power handling in half. So the question to ask yourself is this: is the advantage of getting a lower ohm load worth changing the power handling of the sub, and your setup? Usually, no. Bear in mind that doubling the power results, on average, of increasing the output by about 3dB. Most people say that the actual perception of double the volume to the human brain is 10-12dB. At the end of the day, double the power never equals double the volume. Plus, higher ohm loads tend to be more accurate, acoustically speaking. Hope this helps Samuel!
Hey Tyson my amp is rated at
1. 900w x 2 @ 2ohm
2. 550w x 2 @ 4 ohm
3. 200w x 2 @ 8 ohms
Can I wire a pair of speakers at 8 0hms and a 2nd pair of speakers at 4 ohms and wire a pair of subs at 2 ohms ??
hey what about for 2 15 l7's there 2 ohms but I want them down to 1 how can I do that? or is it possible?
OK thanks but one more question, I was looking at this bd t1500 amp which is rated to do 1000 watts@4ohms, 1500 watts @2 ohm and 1500 watts rms @1 ohm.would this be a good amp to run on that kicker solo X 18, I was told to get a high out out alt, or gage wires and a heavy duty battery up front, would this b a good set up also...If not I'm willing to spend around $700 or $800 bucks for a amp the bd t1500 is $700 bucks
i have a 3000 watt power bass class D mono block amp 1ohm stable amp and four dvc 4ohm 10s what do i do to get it to 1 ohm stable
How do you wire in parallel to a 2 ohm impedance?
i have a cx1200.1 kicker amp an 2 l7 solo baric 15 4ohms whats the best way to wire them to get the best out of them using this amp
Hi I have a question how do I wire 4 15 l7 2ohm together?
Hello i have 2 12 l7 solo beric at 2 ohms the way you did it with the 4 ohms to 1 ohm can i do the same with my 2 ohm l7 to go down to 1ohm
With kickers l7's can you wire a jumper cable from a black w/ white dot to a solid red??? Help please
My jumpers are pretty long ? Will that affect subwoofer output ? Should i shorten the speaker wire ?
The shorter the better,as long as there isn't tension on the wires.
@@KICKER-AUDIO okay thank you no wonder i loss some of my bass! going to rewire them again asap
I have 2x older 2ohm 12" l7's in separate enclosures and a 1000 watt 2 ohm amp... can I wire them to work with this amp ? I nolonger know the model of the L7 so I don't know the rms rating ?...?...?... thank you for your help in advance
🥃cheers🍻
What are the model numbers of the subs and the amp? We would need this info to give you an accurate answer. Thanks!
@@KICKER-AUDIO rockford fosgate r1000 1d & kicker solo-baric L7 12 I believe there dual voice coil farily old back wen you guys had the silver accents on the bezzle.
@@KICKER-AUDIO how can I find the molded number of the subs ? I haven't took one out of its enclosures in many many many years 😅 relics of my youth you might say but the new truck got some much needed love this year!
@@KICKER-AUDIO finally found the model it's an S12L7
There was only one cable going to amp ?
What is you want to wire 2 dvc 4ohms to 2ohms?
On a two channel amp wich of the two channels should i use.
Thanks for the advice
I have 2 15" cvx dvc 4 ohm is 2 way to conect 1 0hm and 4 ohm and I have kicker cx 2500.1 i guess is the line before the zx models but this amp is 2 ohm stable right so I have to wire my subwoofers to 4 di you have a video to see
Two 4 ohm dvc subs can be wired to 1ohm. Go to www.kicker.com/kickeru for a diagram.
ok if you please tell me what to do, i have two 12inch kicker L5 4ohm subs and a zx750.1 amp. how can i get the most from it?? please please tell me.
With a pair of S12L54's you can wire them to either a 4 ohm or 1 ohm configuration. The ZX7501 is is designed to work best at 2 ohms. Ideal situation would be if you could exchange your dual 4's for dual 2's. If this is not possible, one option would be to wire them in a series/parallel configuration and run them to the amp. This would only show the amp a 4 ohm load which would decrease the power from 750+ watts to 375-400 watts. Another option would be to run only a single S12L54 wired in parallel to the amp. This would push 750+ watts to the single sub and you would have to keep all the gains and bass boost down and watch out for overpowering but it's an option. We would not recommend wiring down to 1 ohm as the amp is not stable. It will run at times but not consistently and all the shutting down will eventually cause issues with the amp.
KICKER, i have two 4ohm kicker cvr 10inch subs but my amp gives max performance on 2ohm... how do i correctly run my wires? or do you have a video that explains that already? please help! Thanks... Great videos by the way, tons of info to the rookies like me!
Red with white dots white with black dots black dots with solid red. Red with white dots. Solid white with red dots. See. It’s simple. Was the red with white dots negative or positive. The solid red means power the white stripes mean ground. Camera was too far away couldn’t see these stripes and solid dots or a overhead view would have been perfect. As much as I’d like to say this video helped, I’m going to have to watch another video. This one left a little something to be desired.
But seriously. Red to red. Black to black on each speaker. Then run 1 set to the amp. Right?
Yes, you are right. We did the red/black with white dots to note what voice coil you are connecting (Coil 1 vs. Coil 2).
@@KICKER-AUDIO
Thank you. Appreciate it.
I have 2x 07CVR124's, what wattage amp should I buy?? What should i look for? Ive read around a bit but I have found many different answers. Also what guage sound wire should I use for the best sound? Should I wire them the way you did up above? Forgive my noob questions, I am prepared to learn though ;) Thank you, looking forward to hearing back :)
The RMS is 400 watts per sub, so you're looking for about 800 watts total at 4 ohms (you'll want to wire them series parallel). This is the best one: www.kicker.com/44KXA16001
i ended up wiring the - to - and then the + to + on each speaker individually, then choosing one - and + from each speaker and putting it to its own output from the amp instead of wiring the speakers together.
OK and what ohm load did you get before you hooked up the amp? Did you put it on the meter?
No i did not check with a meter. I have a test in my shop though. Just dunno how to check for ohms with it. Im a noob.
This video is for a different ohm load sub, but it does show you how to wire in series parallel and how to check that with a meter. I've bookmarked the video to start with how to check your final ohm load: ua-cam.com/video/htx0aXmzFmo/v-deo.htmlm24s
Question: I have 2 speaker inputs on my 1 ohm stable massive n2 amp.. do I wire like he did . And just use the one side of the terminals on amp. I believe they are bridged to make 1 ohm inside the amp
..please clarify
Sorry, never heard of "N2". If they set up their terminals like we do on our amps, the 2 pairs of terminals are mainly there for convenience, so you dont have to jam too much wire into your sub's terminals. Just to be safe, please check with Massive and verify that is the case. They may have that info on their manual as well.
I have not found anyone giving me a video or written a display on wiring these speakers.
How would I wire 2 2ohm DVC L7 subs to 1 ohm at the amp
Hey I have kicker solo X 18 and I was wondering could I power that speaker with a amp that pushes out 1500 or 2000 rms with no problem? Oh and I how would I know if it's a 2 or 4 ohm coil....I guess it would b a 4 ohm by it having 2 positive and 2 negative coils rite? I'm kinda new to the audio world
Hey Kevin - the S18X can handle the 1500 -2000 watts without a problem. Make sure the other settings on the amp like the gain and bass boost are set at the right levels to be compatible with your headunit. We made that speaker in both a dual 2 ohm and a dual 4 ohm version so it could be either. If there is not a sticker or anything on it to tell you what the ohm is you will need to test each coil on an ohm meter to see what it reads. If it's a dual 2 then each voice coil should read a little less than 2 and the dual 4 ohm will read a little less than 4.
Is it possible to wire a 4 ohm speaker single voice coil down to 2?
Unfortunately not by itself, no. You would need a second 4 ohm SVC to parallel it with.
I have
4 - s8l7
1 - 1500watts rms mono block
can i wire them down to 1 ohm,
what kind of amp should I buy if it's 1ohm stable
Just out of curiosity if I have 2 terminal ports on my box could I run both subs out to the box and then run both to the amp so that the power goes through both subs quicker so that it's not running through one sub and then to the next. I have 2 kicker l7s and a hiphonics 2400 monoblock amp thanks...
One thing to keep in mind is that the L7's are dual voice coil, so if you want to connect them to terminals, you will be changing the ohm load you can deliver. Granted, you would end up doing that anyway, whether it was from the terminals or not. As long as the new ohm load works with your amp, then there's no harm in doing that.
Oh and I was also told the speaker is 10,000 watts and 5,000 rms or 3,000 rms idk, so would 1500 watts rms hurt that speaker by under powering it? I been told alot of different story's idk what to believe that's why I'm asking u Mr kicker...oh and it's a 4th speaker so I'm a get it wired down to 2ohm
Originally this speaker was designed for SPL competitions, It is able to handle 5000-10000 watts peak but only recommended for those 20 second bursts to get the top reading. When people began using them in their everyday systems, we explained that for continuous music, the RMS value would be around 2000-3000 watts. The different power handlings are based on the type and size enclosure you are using. Do you have your box information?
is that the way to get fuul power out of the l7
hello I need help I have two low kicker L7 of 12 inches 750rms I am moving them with a boss power phantom of 5000 watts but they tell me that they do not hit much. I want to know if you recommend switching power? urgent help ¡¡¡¡
There could be many issues. The wiring could be incorrect, the power insufficient, or there could be a technical problem with the amplifier or subwoofers. I would suggest one of two things to do next: either bring the stereo back to the shop that installed it and let them diagnose the issue(s), or call our Technical Support department. They are open weekdays from 8-5c at 405-624-8510. Thanks!
You're diagram is different from what you said, jointing the 2 speakers you said black to red and black to red. Diagram shows red to red and black to black
No I don't have my box information cus I bought the speaker in a built box 2nd hand about 4 years ago, so Idk where the guy is now to ask that question, all I know that the speaker works,so if I put a good 1,500 or 2,000 rms amp on it, with a high output alternator,0 gauge wire and a good big battery up front would this be ok? Cup I'm not trying to push them at 3,000 rms...would the bd t1500 or the zx 2500.1 work also
Either amplifier will work. I think you will like the sound performance better if you went with the ZX25001 because of the increase in wattage.
How do I wire 2 dvc 4ohm subs to a 2ohm load final to run to an amp....working with 2 skar vd 12 dvc 4ohm
Unfortunately, you can't make a 2-ohm load with a pair of dvc 4-ohm subs. Your choices are 1 ohm or 4 ohms.
Does it have to be the white dots to the amp or can it be the other way around or mixed up but still be + to + .... - to -
Ex: the ones that lead to the box terminal... can it be a (+ w/ ○) & (solid -) ?
Did you ever get a answer ?
KICKER what difference will it make if I set my set up like this ??? will it be better than 2 ohm ??
With some amps, the lower the ohm load, the higher the power rating. We recommend you match the RMS of the amp (at that ohm load) to the RMS of the sub(s). Please check how low the load can be for your amp. It varies by manufacturer.
Ok I have a quick ? So I have two dvc 12in l5s that are 4ohm and a dvc 12in cvr 2ohm sub and I was wondering if I could wire these all together on my sound ordanace 1500m amp?
Couple of things - you don't want to mix the same size subs that are different models. The sound difference when they play would muddy the sound and it won't be good. You could cross them over at different points but it's still not something we would recommend. Next the dvc 2 ohm speaker would see a different amount of power then the dvc 4 ohm subs due to the resistance of the voice coils. The M-1500 is rated at 500 watts RMS at 2 ohms or 300 watts at 4 ohms. Unfortunately this will not work with the pair of L5's because you would only be able to wire them into a 1 ohm or 4 ohm load to the amp. You could run either a single S12L54 wired in parallel to the amp and it would see 500 watts or you could run the CVR122 in series to the amp and it will see 300 watts. Hope this helps.
How do I find the ohm load to my amp? It's a 1600 pioneer champion series 2ch... And I got 2 L7 10" subs with a 4 gauge amp kit 125a in line fuse 3farad vm audio capacitor ...
Best way to find the details of your Pioneer amp is to check their website, usually in the tech support area. Find the instructions, and the ohm load tolerances should be printed there. The model number should be on the amp somewhere.
I got two 1500w 4ohm duals and a 2ohm 5000w two channel amp. What would be the best way to wire them for maximum performance?? Do I have to bridge the amp??😕
What is the brand/model of the amp? That will help us determine the best way to wire it.
I was always curious about the hole that gets drilled in the divider. If it makes a difference in sound quality. This is the first time I've heard anyone say one way or another if it makes a difference in the sound of your subs.
Brandon Burks That small of a hole to run your wires thru will not cause a sound difference. We normally recommend each sub having it's own air space. We feel like each speaker can perform better and if something happens and one blows, the other is not working in twice it's recommend air space and can blow easily.
+KICKER Is it possible/recommended to connect each woofer to the terminals and run the jumpers between the terminals? Rather than drill holes and run the jumpers from speaker to speaker.
@@Maverick_Van_Traveller yes
Sonif I have a 2500.1 soundstream and. 2 audiopipe 15s it's best to run them not togather in parallel for 10hm instead run the separate positive to postive neg to neg to the run 4 wires from the mono block
how in the world can you wire subs both series and parallel at the same time that's not possible you will melt the voice coils on the subs
So u only connect one side of the box inside
No, you would always connect all the subwoofer terminals.
@@KICKER-AUDIO how u said only one going to amp right so how would I do that
I’m talking about the box not the subs
Some enclosures have a single set of terminals, some have more. You need to know the ohm load of the terminals (check with a multimeter) to determine how to wire them to the amp. Tech Support's contact info is: support@kicker.com or 405-624-8510. They are open weekdays 8-5 CST. They can help you wire it correctly.
My amplifier is 2Ω stable and 40 bridged. My subs are 40 per sub now. Their 40 DVC. I want to bridge my amplifier 40 mono bridged. Do I wire them together to get a final impedance of 40 Thank you. Im looking to get the maximum power.
2 ohms stereo and 4 ohms bridged usually gives you the exact same amount of power, so you're fine either way. You can follow the directions in this video to give you 4 ohms bridged. You can also go to this link to grab our free app, Kicker U. it has wiring diagrams, box building info, tuning info and much more. www.kicker.com/kickeru
can you bridge this diagram to amp?
Depends on the amp. Can you tell us what you have? We want to make sure we give you accurate information.
Sooo can this be achieved by wiring red to red and black to black and running them on a bridged channel on a monoblock amp? Or can i do red to red and black to black and run each sub to their own channel
Amp is a fusion powerplant pp-am200010 2000w class d mono block soo to clarify... do i wanna doneach sub red to red and black to black and go to each channel.... or wire them together like this.... and go off of one channel
What model of sub do you have and how many of them?
I have 2 of the S10L7's dual 4 ohm subs
Unfortunately the math doesn't work out on that. You can do 1 or 4 ohms with those subs. Since you have a mono amp, they probably designed the 2 sets of inputs as a matter of convenience during setup. It's still one channel as far as the amp is concerned (unlike a stereo amp, where each set of inputs is independent). We made a free app to make wiring and tuning easier. You might want to check it out: www.kicker.com/kickeru
I just purchased 2 l7 4 ohms 12inch subs. I want to wire them down to 1 ohms, what is the strongest amp that I can use?
You will want to look for an amp that pushes 1500 watts RMS at 1 ohms mono. Hope this helps.
can do this wit 4 speakers the amp I have is 2100 Brutus amp speakers r 1000 peak each n 500 rms each
Please help...What gauge speaker wire is that!
Daniel Macias The gauge wire that Tyson is using in the video is 16 ga.
What if I only have 2 connections 1positive 1 negative?
I just got 2 kicker comp c
Then you have 2 simple choices (assuming its a 4 ohm voice coil): 8 ohms (series) or 2 ohms (parallel).
@@KICKER-AUDIOI wired them sending negative to the other negative on the other sub, same with positive and ran them out to the amp, is that right?
Ty for your response
Do i have to jump 1 sub to the other or can i just have 1 sub qired to a 2 ohm load and other sub at 2ohm load then i have 2 positives and to negs can i run both positives and both negatives to the amp and still get 1 ohm load or do i hav to jump 1 sub to the other. Or is that just a way to get more power?
Jeremiah hodge You always have to have positives and negative’s connected for every speaker. As far as the amplifier connection, some amplifiers are one ohm stable and some are not. You would have to check your app to make sure it’s capable of that load.
KICKER what i am saying is i have 2 12 L7s 4ohmdvc and a 2 12 box with a divider if i run one sub to 2 ohms and the same with the other sub. I have 2 terminal caps that leaves me with a positive and negative on 1 side and same for other side. When i hook both of those to the amp will i still get a 1ohm load i have a 1200.1 kx my manual says 1 ohm stable. But the way the video shows it has one sub ran to the other sub and then lwft with just 2 wires. Is that a better way or the only way i will get a 1 ohm load my amp is like 15 years old. When best buy started selling kicker? I already blew up a 1250.1sdx because i ordered a 1200.1 kx offline and they sent me the sdx model and manual that came with it said 1 ohm stable but when i looked recently it says 2 ohm stable online. The lil digital screen just says service. But i was past warranty. I still have the sdx.
On our mono amps, we have two sets of terminals to make wiring easier. What you will do is attach each wire from each terminal cup to the amp. This will result in a 1 ohm load. It is effectively the same as twisting each + wire together and each - wire together, like you used to do on a mono amp with just one set of positive and negative terminals.
One other note. I just learned that we do still repair that amp. The charge generally ranges from 75-125 depending on the issue. If you contact customer service they can give you the details, assuming you want to repair the amp. The number is 405-624-8510. Open weekdays from 9-5 central time.
When i plug the positive and negative to the amp...do i bridge it..or run off the regular positive and negative
What amp do you have? If it's mono, you do not bridge (though they often have 2 sets of terminals now, for convenience).
Rockford fosgate r1200-1d 1 ohm stable
I have 3 dual 4 ohm subwoofers I wire them down to to 2ohm and I wired all three together and I get .5ohm well I need an amp that is a half stapled or will 1ohm do
You would need an amp that is .5 ohm stable. Most amps that were 1 ohm stable would play at .5 ohms but you would not be able to turn up the volume and over time it would work the components harder and cause them to fail quicker.
im having problems wiring my quad kicker subs.need help!!!!
What's the difference between the l7 4ohm and 2ohm? Which is better
Different ohm loads exist to get the most out of the amp you're using, and/or to let you use the number of subs you need to create your system. All of the subs of a given series and size have the same specs, whether they are 1, 2 or 4 ohms. Make sense?
How can i wire 2 (L7) 4ohms dvc to a final 2ohms impedance... is it possible????
Champion boy Keshan sorry but no. Physics gets in the way of that.
What kind of wire do you used to wire up the speakers?
We generally use either 12 or 16 gauge speaker wire.
They reco.end that for casual liatening. If u r goin to be pushin em hard juat use 8guage . it keeps the heat down and u dont hav to qry about what brand wire you r using trust. Ive been threw about 16 dif L7s since 1gens. U want best currsnt possible. Always remeber they want u to buy more. Thats y they quit the solo x's cuz u could fix you're self
I have 2 dual 2ohm kicker l7 how will i wire them both to 2ohm load???
Devante Mccoy You will want to do a series/parallel configuration. Wire each dual 2 ohm sub in series, then you will parallel them together and this will give you a 2 ohm load.
You have a video on that
I have a problem... I need a contact
i have a teknique performance icbm digital monoblock amp 1 ohm and 2 kicker L712 how is better to conect
Manuel Villalaz What is the model number of the amp?
Does this go for the l7 subs now a day's i have 2 l7 10 d4 subs from you guys?
It does. There is no difference in how an ohm load changes from sub to sub or speaker to speaker.
i wired my dual 4 ohms l7 15 inch to 1 ohm parallel how you showed on video on to a 2000 watt hifonics brutus elite would i burn something?
Does your amp handles a 1ohm load? if so you should be fine.
I found the specs on the bex-2150-1d, and it said it was 1 ohm stable. If that's the same amp, then you're good. I'd go to the hifonics website to confirm if I were in your shoes, or contact them directly.
KICKER i burnt one of my subs i just want to see if you would know why so i wont burn another one sorry im just new to this i was thinking because i was messing with the bass test tone trying different hz to get my gain from my amplifier
There are several things that can lead to a subwoofer failing. Sometimes its the sub, sometimes its the amp, sometimes its the tuning or install. We can help you diagnose the problem if you give us a call. Tech Support's number is 405-624-8510, and they are open weekdays from 8-5 central time. They're happy to walk you through it, so you can tweak your system.
What about 2 2ohm solo baric L7 type R subs run to 1 ohm
You can use the wiring wizard in Kicker U (www.kicker.com/kickeru) for wiring diagrams if you like, but unfortunately 1 ohm isn't possible with a pair of 2 ohm DVC subs. 2 ohms would be the lowest, unless your amp is 1/2 ohm stable.
how many watts from the amp would I need if I wired two kicker comps to 1 ohm and do I use a mono block amp
All if 500 watt u would have 500 watt
+Bobby Eissler how many watts would I need to power 2 12 hifonics if each one was 450w rms and 900w max
+Bobby Eissler and if I wired them two ohms
I've been looking for help on a setup I'm putting together I have 8 15" 1000 to 2000 rms range subs they are split between two 4000 watt mono amps so 4 to each amp I know I can only go as low as 2ohm to each amp they are wired and working but I just want to know what's the best wiring setup my box dimensions are 32" wide by 64" long and15" high sealed in a 94 geo prizm double 20 farad caps double alternator and double battery I know what im doing just not in the sub wiring dept
Adam Corte Hey Adam - on your subs, are they dual 2 ohm, dual 4 ohm, single 2 ohm or single 4 ohm?
Completely left that out sorry they are dual 4 ohm
Adam Corte Not a problem! You are going to do a wiring configuration that includes both series and parallel. For each set of 4 woofers, wire each dual 4 in series. This will create 4 x 8 ohm woofers. Then you will wire all four in parallel to create a 2 ohm load to the amp. Hope this helps. If you have further questions just let us know.