Skinboat Manufacture, Teil 2, canoe build, skin-on-frame, DIY Kanu
Вставка
- Опубліковано 10 січ 2017
- Herstellung und Einbau der Rippen
Making and build in the ribs
Meine Ausstattung:
- Kanu Ausrüstung*: www.denk-outdoor.de/kanu-kaja...
- DJI Maveric*: click.dji.com/AIQLk4gDBn-ioRc...
- Gopro 7*: amzn.to/3JEwutF
- Akkus Gopro*: amzn.to/37I909y
- Zubehör Gopro*: amzn.to/3Jy4ojr
- MacBook zum Schneiden*: amzn.to/37gQllp
- Bildschirm zum Schneiden*: amzn.to/38PiIH
--------------
HINWEIS: Die mit * gekennzeichneten Links sind Affiliate Links, die zum Partnerprogramm von Amazon/Ebay/ gehören. Der Link ist lediglich ein Vorschlag. Der Preis für euch bleibt gleich und euch entstehen keinerlei Mehrkosten.
Solltest Du ein Produkt über einen dieser Links kaufen, bekomme ich einen kleinen Anteil des Umsatzes von Amazon.
Dadurch kann ich noch mehr coole Produkte Kaufen und euch zeigen wie sie verbaut werden! - Спорт
Thanks for part two.
Браво Майстер! Абсолют загенхафте Арбайт, айнфах айн хедверклихес гедихт! верс нихт лезен канн ист айн блёдер веси )))
Danke für den sehr speziellen Kommentar. Erstaunlich wie leicht sich das lesen lässt, nach soo langer Zeit - hat Spaß gemacht !!!
@@bluewondercanoe Goldene Hände hast Du Maestro!
thanks for post in youtube the project, I'm from Brail.
Very well I work my congratulations. regards
qué lindo! sus hijos o nietos terminarán la canoa!
Es un trabajo muy complejo , pero al final muy satisfactorio .
sí, por supuesto: un largo camino a un buen destino ...
Zer gut!
Going back through your videos to determine the inwale thickness you used. Can’t seem to find any information. Have my ribs done for the Prospector and intended to make the inwales at 5/8” but they seem to be too thick to bend in sheer. On your Prospector it seems you sized them about that thickness but used a thinner crossection for the outwale. Do you have some suggestions, Please?
the thickness of the inwhales is 8mm. the outwhales are splitted: 5 and 8 mm ...
Friend where can I get the plans for mounting the ribs?
Como sabéis las medidas de los moldes? Alguien los tiene o lo podría pasar?
Sehr gut! Aber was für ein Kleber (Wasserfest) ist dafür geeignet? Danke
Dietrich Lenk Ich verwende PONAL. Man kann auch mit epoxy kleben, dauert halt länger.
Danke, ich wohne in Brasilien und hier gibt es leider nicht PONAL. Ist das ein Kleber auf PVA Basis? Hier hat Henkel eine Fabrick, aber nicht alle deutsche Produckte!
Dietrich Lenk ok, dann nimm einen Kleber auf Epoxidharz-Basis, der ist dann auf alle Fälle Wasserfest.
You could put a propane torch to the stainless steel to get more heat into the wood if such need arises.
thx, but there is no more heat necessary. the steel-strips are only good for saving the wood-fibres on his place....
Where can we get the plans?
You can use the plan of any woodstrip- canoe as you like. The lines are smooth for skin on frame production. The canoe will be about 5cm wider... No problem.