As I mentioned to you earlier, I have a charger circuit whose output voltage is 48 volts dc . This circuit consists of a three-phase voltage source, a step-down transformer from 400 to 68.82 volts connected to a full-wave thyristor. I want to apply this circuit to the Matlab so that I can charge the 48-volt battery. I need your help to know the results
Assalamualaikum warahmatullahi wabarakatuh can you help me apply fuzzy logic to the video, "Three-stage solar battery charger simulation in MATLAB SIMULINK Buck converter based solar charger". I have an article about this but I'm confused about how to control 2 fuzzy outputs for MPPT and Voltage regulator. Thank You Wassalamu alaikum warahmatullahi wabarakatuh
Thank you for this wonderful video. I hope you will help me. I have a charger and I want to charge the 48 volt battery. I want to apply it on the quantum.
how can i simulate these three stages along with mppt with buck?
When battery is connected then what about load resistance value for buck converter design ????
Great work done !!!!!
Great work done by u.
I would like to do same type system for 6kw system for 96v 150ah battery then how to design converter ????
If i will connect 6 battery of 12v then how to check the status of battery output using bus selector ????
Sir how I can speed the simulation I don't understand how you do it. Thenks
U have uploaded buck converter design video also. Same design for buck is applicable here ???
Kindly reply.......if we use same design then what about load resistance ????
As I mentioned to you earlier, I have a charger circuit whose output voltage is 48 volts dc . This circuit consists of a three-phase voltage source, a step-down transformer from 400 to 68.82 volts connected to a full-wave thyristor. I want to apply this circuit to the Matlab so that I can charge the 48-volt battery. I need your help to know the results
Thanks a lot bro your efforts are lit ❤️
why did we chosee solver ode23tb
Assalamualaikum warahmatullahi wabarakatuh
can you help me apply fuzzy logic to the video, "Three-stage solar battery charger simulation in MATLAB SIMULINK Buck converter based solar charger". I have an article about this but I'm confused about how to control 2 fuzzy outputs for MPPT and Voltage regulator.
Thank You
Wassalamu alaikum warahmatullahi wabarakatuh
For 330w panel of 5x4 panel array become 190.15v and 34.76A , .....for this im not getting proper result for either buck or boost........
Thank you for this wonderful video. I hope you will help me. I have a charger and I want to charge the 48 volt battery. I want to apply it on the quantum.
If battery is connected then what is value of load resistance for buck converter design ??
First, design buck converter using load resistor of any value, then remove load resistor and connect battery in place of it.
@@ahsanmehmood9229 ok i will try
@@ahsanmehmood9229 if i will replace battery instead of load 200ohm then o/p power becomes zero......
Is it necessary that load resistance is equal to battery internal resistance while designing boost converter ???
What should be load resistance value while designing converer for battery connected load of 96V 150Ah
Sir please make a video of PV array (boost converter) with Battery (bidirectional converter)
Do you have any implementable research paper related to this topic?
Yes sir
Hloo
It's mux Or demux?
At which point of video?
Great work dear sir,
can you do simulation of mppt on partial shading condition through P and O method please
Sure, but it will take some time as I am busy with some other work these days.
great work, thank you so much. can you do simulation related energy management system?
Can you send me 'implementable research paper' related to this topic?
@@ahsanmehmood9229 kindly give me your email
amehmood.engr@outlook.com
Email is also given in About section of my channel.
@@ahsanmehmood9229 Thank you
Sir kindly do needful and make video for 96V 150Ah battery charging using 6kw system
Sir Can we implement it in PSIM?
Yes, in PSIM latest versions only, but their licensed version is not available.
@@ahsanmehmood9229 thanks for reply sir..
I have que..I psim, for application of battery charging how we can get a specific output voltage with mppt?
Do you have licensed version of PSIM v12 or later?
@@ahsanmehmood9229 Not now but i will arrange it within month
Okay.
Greetings sir. Would you please be kind enough to give the code or as a link
Complete code is visible in the video.
Thank u so much 🙏
Great work and a bundle of thanks.
Sir I need to contact you.
GIKI se ho sir.. FEE
Sir kindly do needful and reply for further necessary action please.......as i have given all detail.....
.if possible please make video on it........
Sir kindly help me , i have mailed u in detail
I have mailed u sir kindly do needful for making video ..........