There are more steps that aren't in this video, after speaking to Aprilia to FULLY derestrict it this is what you must do: - Change the exhaust for a sport one and get it derestricted by the shop you purchased it off - Cut the black/white wire or replace with Malossi Digitronic - Remove variator washer, it's welded on so you will need to buy a replacement that's unrestricted - Any size rollers will do and subject to popular belief rollers unless they're well off won't effect top speed. 5g should be fine though. - Remove restrictor in the Carb mouth - Upjet (this is dependent on your bike and what mods you have on it but if you've just done the above a 68 main jet will suffice) it's incredibly important you do this step because if you change exhaust and carb there will be a lot more air into the engine, you will run Lean and eventually damage your piston leading to a seizure. - GEARS, here's the hidden one. On the Euro4 models they have a shorter secondary gear than the earlier models. This means with stock gearing you won't go above around 45mph. When the speedo shows 50mph (mine does same as this video) it's not accurate GPS will show around 45mph real speed. Change the gears to Malossi Primary Gear Up Kit 14/39. You can change the secondary if you prefer but this is a slightly harder job compared to changing the primary and will give the same end result. Once all above is done INLCUDING the gear up kit, you will get around 55mph true GPS speed the speedo shows about 60 (goes past the 50mph max). I can't stress enough though UPJET!! Brad speed shows how to change the primary gears on Aprilia SR 50 on UA-cam. Hope this helps someone!
Great post, but just a nitpick: neither the procedure in this post nor the one in this video are 'derestriction' or 'unblocking'; they're 'upgrading'. 'Derestriction' only involves removing/disabling mechanisms that are present which artificially limit the performance - e.g. removing variator spacer ring, opening up exhaust holes, etc. Replacing components entirely with those with specifications that exceed the original, is 'upgrading'. Both are 'improving', but the distinction is important, especially for newcomers who can get confused.
How did you remove the left cover to remove the black and white wire? I've been trying to but it isn't coming out. Will the scooter start if I the wire?
Would you make a video on different exhausts that fit the sr50r 2018, I am struggling to find an arrow extreme or gianelli reverse that fits, or send me a link to a gienelki reverse that fits sr50r 2018 , nice vid btw subscribed 👍
gianelli reverse is for 70cc, and looking for many other settings you won't have a good start (you need to put the appropriate lamella, multivar carburetor 19 and piston and cylinder 70cc to get the effect) in my video is the cheapest and most efficient variant for 50cc !!!
Petrushevski YT does this one fit? www.ebay.co.uk/itm/EXHAUST-GIANNELLI-EXTRA-V2-APRILIA-SR-50-DITECH-2004-SILENCER/191950358188?epid=8017021710&hash=item2cb12206ac
@@jakupkvilt better u buy the gianelli reverse or maybr yasuni r of leo vince touring .. the v2 is very bad build qlty cheap but not good for the long run
Would it be possible for you to make a video showing the carb. I have heard its electronically controlled but I cant find any pics of it, just interested to know how the restriction in the cdi affects the carb. Thanks.
Druze imam aprilia 2019 so reverse odi 75 max 80 udolnica neznam dali e cepkana vo prenosot gledam deka e otvarana ja imam samo 2 dena. Inace korne na start. Dali ke dobijam nesto ako ja izvadam zicata i dali ke vlijae vrz izdrzlivosta? Pozz od gostivar 🇲🇰
gianelli reverse and record are for 50cc, they can be put in a 70cc kit but it wont make a good effect.. Yasuni R is the best exhaust for 50cc.. btw what does the white wire do? makes more rpm? ive never done that just put better parts with gianelli reverse and my does 85 with me up to 90.. but never unplug the wire
@@jakupkvilt i dont know why the v2 .. even on the original website the reverse is even better or the yasuzi z the polini team 3 the leovince handmade zx or the leovince touring the gianelli v2 is actualy the worst..
@@mir8902 there is electronic speed limiting for the first 600km - after that it will rev faster. or you can take out the black and white cable like the video shows.
Cool , revs are limited by your chosen pipe and it's specifications they tell me ? I would say 9000rpm for your top speed, interested l am now . You could lift the front wheel with the 70cc. Thanks
dear Petrushevski YT,thanks for quick answer , i understood , that after i discinected white-black wire it need to change the exhaust to increase speed to more than 50 . but the standard exhaust connected to engine with additional tube . what to do with that tube, giannelii doesnt have such tube (close or ?)in the end i had to do something with the variator (change rollers or ?)/ With respect fot you p.s. gianelli extra v2 has different modifications / which one should i buy ?
ekim andersom I have brought a 2018 rs 50 r and only goes 45kmh I have bought Mallosi roller kit and exhaust aswell as different jets will this increase the speed ??
Kolku grama se fabrickite rolni menav gianeli revers mi ide 80 85 so da menam da ide 90? 100 klip cilidar ili uste mi se fabrickite rolni da menuvam 4.5 grm ili
I have a 2018 Aprilia SR 50 and i can only get it over 50 when I’m going downhill. Is there anything I can do to get it faster except change the exhaustsystem?
Posle blokazu , Skratuva i se zivoto na apriliata za 70% , poarno smeni blokadu i odma nekoj kit klip lagercinja , variatori sve novo cilindri da ne zariba za 1 godina toa mi bese zboro :) pozz
I cant find the exhaust you are recommending. The suppliers are saying that there isn't one for this 2018 model. Surely is the same as an earlier model as its still a Piaggio engine and the mounts at the rear look similar
@@mir8902 How did it work and what kind of jet did you use , because I recently bought a 2020 euro 4 aprilia and dont know what kind of exhaust to get?
you must change variator obligatorily or else you will stay at 50 kmh puts a Multivar2000 just with its you have to do at least 80kmh no need to change the exhaust pot you will be blocked at 80kmh maximum 85kmh to exceed the 80kmh you have to change the gear box, I recommend a 15/38 primary gear, with his me I make a 115kmh 120kmh, my specs: variator multivar 2000 4.7g, wild lion exhaust, primary gear 15/38
must unlock the electronics, giannelli record is for 70 cc understand !!! and look for other settings (multivar, piston, cylinder, lamella, lamella springs, etc.) my video is the cheapest variant
@@skrivelis4315 nothing it doesnt wok 90% of this video is not true and not good exhaust ... buy the malossi digitronics and for exhaust the s6 pro replica or gianelli shot or yasuni r 👍👌
500 km projdeni moze extra , 1000 put sam rekao svak auspuh trazi razlicita podesavanja . Extra je za 50 cc i trazi manje podesavanja i jeftinija varijanta . Reverse je za 70 cc po snazan i potrosice klip za 4000 km ,i vise trosli zasto je jaci i zahtevnii ( VIDI DESKRIPCIJU)
The calble is for the speed SENSOR it dont change or unlock every thing just your couter of speed goed wrong... look this guy is going 40 kmpu but the speed couter is all to 80 you are fucking up you sxooter dont do this u will ruin your scooter
@@8401-t8z plz read a lil u will see what is wrong i do this with scooters almost 12 years this guy is wrong and u will damage yoir scooter its ok bye me but do u really wanna throw away 3000 euros for this model and fuck it up with cheap exhaust and nu further tuning eland carb , clutch variator etc ... its bullshit do it wrigt spend around 600 700 euro 9n parts and that thing wil fly like mine ... ;)
I have a aprilia sr50 2019 and gianelli record and roller 5g and i unblock the white and black But not going again 80+ Can you help me whats the problem ?
Hi, I have the exact same scooter as you! I unbridled everything the pot, the air box, the vario, the cdi, the carburettor! I did not unclamp the transmission! it worked very well because I had put an 80 gigleur with a high speed pollini vario with 63 gram rollers and with the same exhaust as you yasuni! They drove well and picked up speed straight away and went 70 km on the flat and 75 to 80 km downhill! But I had a problem is that I had very hard to start cold! when I rode the scooter, then it started fine! So I wanted to check if I had a problem with my valve box and there I came across my intake pipe which was cracking! I put a new intake pipe back and now it doesn't work! the scooter has very hard to mount them! I'm between 20 km and 30 km up! flat I do 50 to 60! Please help me ! Do you have an idea of my problem, I tried lighter rollers, I put 53 grams today and the scooter is a little better and my gigger is 76! I had to lower my gigleur because I had less air since I gave a new pipe of admission! I'm completely lost ! Could you please tell me the vario you are using and what is the weight of your Vario rollers? And what gigger did you put on? Thank you very much for your help sir
@@flex3vil281 I'm sorry I can't speak French, there are a lot of things that need to be fixed, look for me on Face Book and there I'll follow you pictures of what needs to be done on You Tube, it's not possible
because giannneli reverse is for 70cc cylinders. I curently have it on stock 50cc and it isnt as good as my firends extra v2. But if you are planning to upgrade to 70cc, reverse is better.
Extra v2is a cheap exhaust gianelli reverse is for 50 cc on a 70 ist not good.. maybe a low rev cast iron will do. But a aluminium niacil needs a yasuni c20, 30, stage 6 pro, gianelli shot v4.. like that the extra v2 is just cheap rubbish
I bought malossi digitronic and removed intake diaphragm present in the carburator on air intake. And the scooter goes exactly the same... 45 - 48km/h... :( What can i do?
Everything else is stock. I will remove the ring from variator next. But on 2019 the ring is soldered on the central part. So i ordered the new metal thing part without the limiter. We will see next week how it goes... There must be some kind a fizical blocade as it stop at exactly 45-48 and you can feel its being blocked.
kako si zadovolen od apriliata? planiram da zemam pa da se rasprasam...Kolku trosi so auspluhot i dali toa sto go izvadi kaj elektronikata e granicnik?
@@PetrushevskiYT batence gleda se deka imas pojma dosta e rolnite da gi smenes za da trose povekje ako se poleki a plus auspuho originalen ima rpm blokada deka isto kje trose lol
There are more steps that aren't in this video, after speaking to Aprilia to FULLY derestrict it this is what you must do:
- Change the exhaust for a sport one and get it derestricted by the shop you purchased it off
- Cut the black/white wire or replace with Malossi Digitronic
- Remove variator washer, it's welded on so you will need to buy a replacement that's unrestricted
- Any size rollers will do and subject to popular belief rollers unless they're well off won't effect top speed. 5g should be fine though.
- Remove restrictor in the Carb mouth
- Upjet (this is dependent on your bike and what mods you have on it but if you've just done the above a 68 main jet will suffice) it's incredibly important you do this step because if you change exhaust and carb there will be a lot more air into the engine, you will run Lean and eventually damage your piston leading to a seizure.
- GEARS, here's the hidden one. On the Euro4 models they have a shorter secondary gear than the earlier models. This means with stock gearing you won't go above around 45mph. When the speedo shows 50mph (mine does same as this video) it's not accurate GPS will show around 45mph real speed. Change the gears to Malossi Primary Gear Up Kit 14/39. You can change the secondary if you prefer but this is a slightly harder job compared to changing the primary and will give the same end result.
Once all above is done INLCUDING the gear up kit, you will get around 55mph true GPS speed the speedo shows about 60 (goes past the 50mph max). I can't stress enough though UPJET!! Brad speed shows how to change the primary gears on Aprilia SR 50 on UA-cam.
Hope this helps someone!
Great post, but just a nitpick: neither the procedure in this post nor the one in this video are 'derestriction' or 'unblocking'; they're 'upgrading'.
'Derestriction' only involves removing/disabling mechanisms that are present which artificially limit the performance - e.g. removing variator spacer ring, opening up exhaust holes, etc.
Replacing components entirely with those with specifications that exceed the original, is 'upgrading'.
Both are 'improving', but the distinction is important, especially for newcomers who can get confused.
i have a 2005 sr50r, where is the black/white cable???
@@joelsantos5719have you found it ? Ive just bought 2005r. And im planning to make this changes in my scooter
@@krauze55 on my scooter the black white cable, came from the alternator and got plucked with oder cables in to the cdi, i hope i could help you mate
@AlexBill1994 what would happend if I only cut the black/white wire
i tried to unplug the black and white cable but it doesn't come out how can i not cut it?
How did you remove the left cover to remove the black and white wire? I've been trying to but it isn't coming out. Will the scooter start if I the wire?
just go to the mechanic and show him the video
Transmission is short!!!! You have to buy original piaggio primar and put it or buy a complete gearbox from 2017 and earlier models.
Does buying malossi mhr second gear fix the problem or you need the entire piaggio primar gear?
How did you know that it was short?
Thanks a lot. Very helpfull video for unlock my v2019. With more money i recommand the "malossi flip" exhaust and "malossi digitronic CDI"
flip is rebranded gianelli.dont waste money.
wtf bro just buy a giannelli reverse which is the best 50cc exhaust
Leo Vince TT and Digitrontic
Should still take restriction cap out between carb and airfilter and higher the main jet also doing wat his done big major difference from being stock
Would you make a video on different exhausts that fit the sr50r 2018, I am struggling to find an arrow extreme or gianelli reverse that fits, or send me a link to a gienelki reverse that fits sr50r 2018 , nice vid btw subscribed 👍
gianelli reverse is for 70cc, and looking for many other settings you won't have a good start (you need to put the appropriate lamella, multivar carburetor 19 and piston and cylinder 70cc to get the effect) in my video is the cheapest and most efficient variant for 50cc !!!
Love the video, which is the exact exhaust you bought as when I look there are different sizes so can u send a link to yours ?
What is the original roller weights and is gianelli rekord a good exhaust? Or should i buy gianello extra v2
Petrushevski YT thanks i will
Petrushevski YT do you know where i can buy gianelli extra v2?
Petrushevski YT does this one fit? www.ebay.co.uk/itm/EXHAUST-GIANNELLI-EXTRA-V2-APRILIA-SR-50-DITECH-2004-SILENCER/191950358188?epid=8017021710&hash=item2cb12206ac
@@jakupkvilt better u buy the gianelli reverse or maybr yasuni r of leo vince touring .. the v2 is very bad build qlty cheap but not good for the long run
7.2
if i only remove black and white wire will it go faster?
nah it will go 30 km/h you need to put the exhaust!
@[ Karhu ] it's an rpm limiter if u unblock it without exhaust all the power goes to the 2 pipes in the stock pipe......
Hey, can you tell whats The problem If my top speed IS only 59kmh and i have done alla The same things as you
Unblock the ring on the variator, see another video on YT how to do it
@@PetrushevskiYT i have done that too things, i have derestricted The whole bike
My local scooter service place says that by cutting black/white wire makes nothing on aprilia sr 50 scooters
But I have to buy it the Giannelli muffler and the rollers? Because I have a friend of mine who has this model but it is original and reaches 80 km/h
I have disconnected the black - white cable and it works the same, why? (it is factory)
Did you change any part and how fast can you go
How fast with no changed parts only the black-white cable?
Does it apply for the 2014 aprilia sr50 motard as well?
Mega geil dein mario scrofani super
Bella italia dein mario scrofani super
Would it be possible for you to make a video showing the carb. I have heard its electronically controlled but I cant find any pics of it, just interested to know how the restriction in the cdi affects the carb. Thanks.
Solenoids are controlled by the ecu
If i just plugg out the eletronics and not have gianelli exahust Will it be vad for the engin
Druze imam aprilia 2019 so reverse odi 75 max 80 udolnica neznam dali e cepkana vo prenosot gledam deka e otvarana ja imam samo 2 dena. Inace korne na start.
Dali ke dobijam nesto ako ja izvadam zicata i dali ke vlijae vrz izdrzlivosta?
Pozz od gostivar 🇲🇰
gianelli reverse and record are for 50cc, they can be put in a 70cc kit but it wont make a good effect.. Yasuni R is the best exhaust for 50cc.. btw what does the white wire do? makes more rpm? ive never done that just put better parts with gianelli reverse and my does 85 with me up to 90.. but never unplug the wire
YASUNI R IS FOR 50cc and 70cc soo
Hi i have the same scooter and my top speed is 65 on unblocked, this exhaust is only 80 euros do u recomend beter to buy yasuni exhaust of this one?
Hi i have the same it only go 50 kmph done nothing only 300 km on it what should i do
@@PetrushevskiYT there are 2 kinds of gianelli extra v2 on that website, which one do i pick?
@@jakupkvilt i dont know why the v2 .. even on the original website the reverse is even better or the yasuzi z the polini team 3 the leovince handmade zx or the leovince touring the gianelli v2 is actualy the worst..
@@mir8902 there is electronic speed limiting for the first 600km - after that it will rev faster. or you can take out the black and white cable like the video shows.
@@ConradMcBad no its not true it DONT exist dont try te be cheap and dump BUY MALOSSI DIGITRONICS
2008 aprillia sr50r ditech has the same cable? Or those dont have this restrict?
Cool , revs are limited by your chosen pipe and it's specifications they tell me ? I would say 9000rpm for your top speed, interested l am now . You could lift the front wheel with the 70cc. Thanks
dear Petrushevski YT,thanks for quick answer , i understood , that after i discinected white-black wire it need to change the exhaust to increase speed to more than 50 . but the standard exhaust connected to engine with additional tube . what to do with that tube, giannelii doesnt have such tube (close or ?)in the end i had to do something with the variator (change rollers or ?)/ With respect fot you
p.s. gianelli extra v2 has different modifications / which one should i buy ?
Use gps speedometer the scooter counter can be wrong
It only goes to 50 but mine is pretty accurate through speed traps
Brat elektronikata za da ja odblokiras gi trgas isklucuvas samo crnoto i beloto kabelce taka li?
After mounting giannelli extra v2, what should i do next with carb?
can u make video about aprilla sxr 50?
how do you tune a 2016 model?
hey man, ive just got myself an aprilia sxr 50cc and i would like to unblock it. is it possible if you could show me how. many thanks
See my video and description down
Hi if I do all the things in the video on my 2019 sr50r it will work yes?.
Yes, a good exhaust is a Gianelli Go or Malossi Wild Lion for less money with same result and looks stock
Did you take variater restricter ring out and did you change anything to the jet carberator?
Ok thanks and do u have to take the spacer out the exhaust that keeps it restricted or can u fit it without taking any spacers out- thanks
Petrushevsky cosa ne pensi della nuova centralina uscita della malossi?
what gives if i unplug that white cable in 1:11 what that does change?
That change..? I have this scooter and disconnect wire and nothing.
You need to unplug the exhaust to let the engine rev higher
Nemīz tāpat nepis neiet :D
How did you reach the original exhaust manifold bolts as the left bolt is hard to reach to loosen?
Verschiedene Werkzeug 🛠 dann klappt es so wie bei mir 😎
Can you tell me which box is that ? Its not CDI
Isn't it ??
is yasuni z ok exhaust without any kit?
Can you do this without changing the exhaust and rollers?
sadly no , you have to do all the things in the video
@@PetrushevskiYT ok, thank you
@@PetrushevskiYT what would happen if I removed the wires but didn't replace the other parts?
@@PetrushevskiYT is it possible with orginal rollers an gianelli rekord exhaust?
@@There_you_go_smile no 4.3g for record
Do i need to do the first step? Or can i just unplug the wires?
just unplug the wires
Petrushevski YT no that will make my speedometer go 80 but the bike will still go 50
@@Alan-kj2eg you must to change exhaust to extra v2 and roller weighst to 5.0 malossi
Hi I have same bike as this will the gianelli reverse 2007-2009 sr50r exhaust fit this bike as I’m thinking of getting that ?
It doesn't fit ,search giannelli for 2009-2018 year.
Hello There! Do you know what roller size weights are on stock aprilia sr50 2020?
6.5g
@@PetrushevskiYT Thank you!
you also need to unblock the variator
Nemas video kako se meni auspuhot, i sto napravi so katalizatorite?
I have a sr50 4t motard where is the black and white
What do you intend to unlock the electronics? in practice what do you exclude?
Mine without detaching any wire goes already over 80 km .. but I do not know ....
ekim andersom I have brought a 2018 rs 50 r and only goes 45kmh I have bought Mallosi roller kit and exhaust aswell as different jets will this increase the speed ??
Tack🎉
Funkade det för dig?
How do you remove the black and white wire?
take pliers or scalper pull or take off or wire scissors
Ok i have That bit its stuck
But i Sony want to use a pair of scissors
Or do i use more force?
Kolku ah e akumulatorot i dali ti e fabricki ili go menuvase
Zdravo, imam SR50 2019, dali ima samo blokada na elektronikata ili ima i na auspuh?
od 2018 god pa nagore imaat dr zupcanici i poradi toa max brzina e pomala
Hey ich habe genau den selben Scooter 🙂
Mein Setup
Giannelli Extra V2
4,3 g Malossi Gewichte
66 Hauptdüse Vergaser
Alle Drosseln draußen
Wieviel und welche Drosseln hat der alles?
i took the black and white whip off and it didn't work. my scooter aprilia sr 50 r 2018 then ran only 30 kmh. what is the problem?
You fix it?
How did you change your exhoust
if we put a button to hidden place, can we activate 45kmh for when police testing ?
that’s what i want too. i think you can do it and switch between for police checks.
@@BennyboyTrades its Called a ”Blackbox”
Salut tu monte a combien avec ton scooter aprilia sr stp le pot il coûte combien sur quel site
are there a restriction in gianelli extra v2 if you buy a new and is it easy to remove?
Yeah, there is a washer in the intial curve which is very easy to remove with flathead screwdiver.
Kolku grama se fabrickite rolni menav gianeli revers mi ide 80 85 so da menam da ide 90? 100 klip cilidar ili uste mi se fabrickite rolni da menuvam 4.5 grm ili
frli go u gjubre stoko
I have a 2018 Aprilia SR 50 and i can only get it over 50 when I’m going downhill. Is there anything I can do to get it faster except change the exhaustsystem?
You can derestrict and it should go 60-65 km/h.
campobelli1 finns det en variator bricka på 2018 modellerna aprilia sr50 r E4 alltså ?
campobelli1 så den senaste aprilia med klistermärket med ett A på har en v-ring?
campobelli1 okej lägg t mig på snap : Benja2300 och hör av din när du har fått reda på vad man kan göra
Put weight on 😁
Posle blokazu , Skratuva i se zivoto na apriliata za 70% , poarno smeni blokadu i odma nekoj kit klip lagercinja , variatori sve novo cilindri da ne zariba za 1 godina toa mi bese zboro :) pozz
I cant find the exhaust you are recommending. The suppliers are saying that there isn't one for this 2018 model. Surely is the same as an earlier model as its still a Piaggio engine and the mounts at the rear look similar
Nooo buy the stage 6 pro replica !!!!!!
It will fitt i have too an sr 2018 e4 i fitted it very well gianellia extra is very very bad dont buy
@@mir8902 How did it work and what kind of jet did you use , because I recently bought a 2020 euro 4 aprilia and dont know what kind of exhaust to get?
@@geni.zeqiri you can buy mine...
@@mir8902a bit late but on you 2018 e4 model did you cut the wire or remove it somehow
Hello i have the same i removed the black/white colored Cable but nothing changes... 50 km/h maximum what can i do without buying exhaust
Nothing you have to change exhaust the stock one is shit
Did u remove the variator ring as well as the exhaust block carb block and membrame block ?
Search on google how to remove sr50 gen 3 restrictors and make sure you get them all out.
Max speed should be 60-65 km/h.
you must change variator obligatorily or else you will stay at 50 kmh puts a Multivar2000 just with its you have to do at least 80kmh no need to change the exhaust pot you will be blocked at 80kmh maximum 85kmh to exceed the 80kmh you have to change the gear box, I recommend a 15/38 primary gear, with his me I make a 115kmh 120kmh, my specs: variator multivar 2000 4.7g, wild lion exhaust, primary gear 15/38
Mi R there is no variator ring on the latest models....carb block? Membrane block?
I changed exhaust to giannelli rekord and 4.3 roller weighst have start but end no do i have to unblock Electronic or change the roller weighst
must unlock the electronics, giannelli record is for 70 cc understand !!! and look for other settings (multivar, piston, cylinder, lamella, lamella springs, etc.) my video is the cheapest variant
@@PetrushevskiYT thanks bro
Hi would i need to change the main jet on the carb if so to what size thanks 😊
increase 5 to 8% and look at the spark plug color; needs to be coffee brown
Hi, i have Aprilia sr 2017 and i have bought an arrow extreme and a malossi multivar the rollers how much gram should i put
Maybe try the stock weight.
DarkWarrior10 x which arrow extreme have you bought and will it fit the 2018 model aswell ?
@@scared2death251 i have bought Arrow extreme dark
@@scared2death251 what gram of rules should i put?
DarkWarrior10 x get 5 g Malossi not to light not to heavy
Is better yasuni z or giannelli reverse?
Giannelli reverse is for 50cc, Giannelli Shot is for 70cc
Giannelli reverse is for 50 and 70cc basic kit,giannelli shot is for hign end scooter mid race or race cylinder kit.💪🙂
What does that change when u unplug that black-white cable?
Nothing... u need the malossi digitronics www.malossistore.eu/digitronic-digital-electronic-controller-2t-50-cc-euro-4-5518130B-P
@@mir8902 and what will change if i buy that?
@@skrivelis4315 nothing it doesnt wok 90% of this video is not true and not good exhaust ... buy the malossi digitronics and for exhaust the s6 pro replica or gianelli shot or yasuni r 👍👌
@@mir8902 i have yasuni z , and mby i will buy 70cc dr evulution! Will my exhaust =yasuni z will be good for 70cc cylinder?
@@skrivelis4315 noo its a good exhaust but not good for 70 cc for 70cc yasuni r or yasuni c21, c30,
Aprilia sr 50 2017 4l trosi na 100km so blokazi ako se izvadat ke se pokace li
Do disconnecting the black and white cable also work for the 2017 model?
Okay thanks. So it won't do a difference on the 2017?
How fast does it go if you only unlock the cdi electronics just with the standard exhaust?
Petrushevski YT thanks!
dear Petrushevski YT. Me and my son deiconnected the black-white wire, but the scooter working only until 50km/h. what should we do more?
im add giannelli rekord exhaust but its go 77km/h
can I do it wihout changeing exhaust and rollers?
It will have no effect
Ok ty for answer
колку литри ти троши на 100километри после овие две модификации?
it also
@@PetrushevskiYT fuel consumption after this 2 modifications ?
Can you put it back?
na kolko projdeni kilometra da se smeni auspuh, i dali extra e bolji od reverse
500 km projdeni moze extra , 1000 put sam rekao svak auspuh trazi razlicita podesavanja . Extra je za 50 cc i trazi manje podesavanja i jeftinija varijanta . Reverse je za 70 cc po snazan i potrosice klip za 4000 km ,i vise trosli zasto je jaci i zahtevnii ( VIDI DESKRIPCIJU)
Hi. Have you changed the main carburetor jet?
no
@@PetrushevskiYT thx :)
How did u get the black and white wire out?
did you removed it?
@@662-z2g No, I wasn't sure that I can trust a yt vid but I want to try.
@@lucaswessman3167 nothing will happen
@@662-z2g oh ok, i tried to renovera the ring but it was fused together with some other shit
Remove***
Kolko pare ga kupi auspuh
I rolne malossi?
After you have removed the cable. Can you put it back or is it broken?
The calble is for the speed SENSOR it dont change or unlock every thing just your couter of speed goed wrong... look this guy is going 40 kmpu but the speed couter is all to 80 you are fucking up you sxooter dont do this u will ruin your scooter
Mi R are you sure?
Same engine on 2015?
Io non sono riuscito a staccare il filo infatti lo ho tagliato
What you did is good, it is important not to have contact
Which exhaust is this i can only find giannelli extra v2 for 2016 does this fit too? Or is there one for 2018?
Dont buy that one its very cheap and dont run well .. also the video is wrong .. dont follow this steps or u will ruin yoir scooter
Mi R why should i not follow the video?! Everything is right except the thing with the cdi you need a malossi digitronic but thats it?
@@8401-t8z plz read a lil u will see what is wrong i do this with scooters almost 12 years this guy is wrong and u will damage yoir scooter its ok bye me but do u really wanna throw away 3000 euros for this model and fuck it up with cheap exhaust and nu further tuning eland carb , clutch variator etc ... its bullshit do it wrigt spend around 600 700 euro 9n parts and that thing wil fly like mine ... ;)
I have a aprilia sr50 2019 and gianelli record and roller 5g and i unblock the white and black
But not going again 80+
Can you help me whats the problem ?
gianelli record is for 70cc Gieanelli extra v2 is for 50cc, the record needs a piston and a cylinder and a carburetor to achieve it effect
@@PetrushevskiYT Yes! why none is reading the desc for all the useful information!
@@PetrushevskiYTwhat about giannelli reverse with 4.7g rollers ?
omolged giannelli extra v2?
Tried this and it didn't work. Now my ped cuts out at 16mph
So not worth it?
did u change the exhaust?
@@ludvighagelin8720 It's worth it if you want to spice it up when u have the exhaust changed
Is that steps works with SR50R CARB 2009?
It is only for 2018 + don't touch ANYTHING
what about 2023 ?
Where do you buy gianelli extra v2
Petrushevski YT Can you send link of the exact same as yours.
Istoto go napraviv ima podobruvanje ode 80 no pocna da gree plastikata pod rackite duri klucot na bravata e zagrean sto e rabota ?????
imas mekoj spoj odi kaj elektricar da vidi toa nema vrska so ovaa sto sinapravil da odi povece
@@PetrushevskiYT staviv sporcka svekica nem od nea da e
Hi, I have the exact same scooter as you! I unbridled everything the pot, the air box, the vario, the cdi, the carburettor! I did not unclamp the transmission! it worked very well because I had put an 80 gigleur with a high speed pollini vario with 63 gram rollers and with the same exhaust as you yasuni! They drove well and picked up speed straight away and went 70 km on the flat and 75 to 80 km downhill! But I had a problem is that I had very hard to start cold! when I rode the scooter, then it started fine! So I wanted to check if I had a problem with my valve box and there I came across my intake pipe which was cracking! I put a new intake pipe back and now it doesn't work! the scooter has very hard to mount them! I'm between 20 km and 30 km up! flat I do 50 to 60! Please help me ! Do you have an idea of my problem, I tried lighter rollers, I put 53 grams today and the scooter is a little better and my gigger is 76! I had to lower my gigleur because I had less air since I gave a new pipe of admission! I'm completely lost ! Could you please tell me the vario you are using and what is the weight of your Vario rollers? And what gigger did you put on? Thank you very much for your help sir
What country are you from?
@@PetrushevskiYT I bought my scooter in France
@@flex3vil281 I'm sorry I can't speak French, there are a lot of things that need to be fixed, look for me on Face Book and there I'll follow you pictures of what needs to be done on You Tube, it's not possible
Does anyone know what changed in the euro 4 models compared to the older euro 2 models?
Gearing, cdi, variator bushing
why not giannelli reverse ?
because giannneli reverse is for 70cc cylinders. I curently have it on stock 50cc and it isnt as good as my firends extra v2. But if you are planning to upgrade to 70cc, reverse is better.
Extra v2is a cheap exhaust gianelli reverse is for 50 cc on a 70 ist not good.. maybe a low rev cast iron will do. But a aluminium niacil needs a yasuni c20, 30, stage 6 pro, gianelli shot v4.. like that the extra v2 is just cheap rubbish
I bought malossi digitronic and removed intake diaphragm present in the carburator on air intake.
And the scooter goes exactly the same... 45 - 48km/h... :(
What can i do?
No not 70 cc pffff CHANGE THE MAINJET TO 66
Change the mainjet to 66 oke then it will be fine maybe u have to heavy rollers... what size do u have
Everything else is stock. I will remove the ring from variator next. But on 2019 the ring is soldered on the central part. So i ordered the new metal thing part without the limiter. We will see next week how it goes...
There must be some kind a fizical blocade as it stop at exactly 45-48 and you can feel its being blocked.
@@HopeOfAvatar yes variator is locked carb plate a smaller main jet exhaust block and digital block
Did it work??💪
how to derestrict a 2022 model SRX 50 .HELP
impossible
Jas ja nemam belata i crna zica,imam crna so crnocrvena,bela so portokalova i sina svetlo sina i bela?sto da pravam?
Petrushevski YT da aprilia 2018
Sto da pravam koja da ja trgnam??
kako si zadovolen od apriliata? planiram da zemam pa da se rasprasam...Kolku trosi so auspluhot i dali toa sto go izvadi kaj elektronikata e granicnik?
@@PetrushevskiYT batence gleda se deka imas pojma dosta e rolnite da gi smenes za da trose povekje ako se poleki a plus auspuho originalen ima rpm blokada deka isto kje trose lol
You removed the tubes that went from the metal things at 0:07 to the exhaust, what are those things and do they matter
they don't matter
They dont matter
They turn back air in the engine
Can someone send me a link to the exhaust please
Nooooo not good exhaust very cheap
To unblock cdi u need to buy malossi digitronic
Better than cutting the wires if you have cash. Yes you have to either get a Digitrontic or disable the sis system via the two wires.
Hi, is this a two stroke or four stroke?
Two stroke
Hi
Do you need to have atleast 1000km to unblock your bike?
No you should just have done the brake in which is roughly 500 km, then it’s all green
No its not true 1500 at l3ast ...
xd, took all those restrictions off at around 300km, less strain on the engine and can work more freely
Do you have it with original 50cc cylinder? Or 70cc
Petrushevski YT thanks