Nice work as always, I like how you did several real slow passes with the camera on the finished knife so we could appreciate how awesome it turned out!
It definitely put a whole lot of work into this, good thing you had to power tools that would have taken weeks if not longer.. Thanks for sharing. Keep looking up by for now your new friend Ken God-bless
I use a mixture of ferric chloride and distilled water (regular water will work as well). I make sure the knife is hand sanded up to a high grit (I normally go up to 600 grit) I let it set in the ferric for around 5 min then take it out, spray it with windex and use a piece of 1000 grit sand paper to remove the oxides that are built up on the surface then repeat the process. I usually do this 3 times, after the last cycle use a mixture of baking soda and water to neutralize the acid. After the knife has dried I will mix a substantial amount of instant coffee with cold water and let the knife sit in it overnight, this turns the black portion of the blade extremely dark, after it is rinsed and dried off, apply oil or a wax like axewax to the blade and your good to go. Thank you for watching, I greatly appreciate it.
I use a pair of v-bit tongs and a pair of wolf Jaw tongs for 99 percent of my forging, I also keep a set of flat jaw tongs and a couple of different sized scrolling tongs. I appreciate you watching.
This knife is already gone, but when I have them availible I sell monosteel for 150 and random damascus for 275 with a sheath. Thanks for watching, I appreciate it!
I have some available on occasion, they can be found on my Facebook page, the link is in the about section of my channel page. I appreciate you watching!
@@Mysticmountainforge thank you. I’ve been using 14tpi Milwaukee, but lately they haven’t seemed like they are lasting that long. Thank you for your response, and thank you for the content
Nice work as always, I like how you did several real slow passes with the camera on the finished knife so we could appreciate how awesome it turned out!
Thanks! I appreciate you watching. I like how this one turned out as well, definitley one of my favorites.
Very Nice Work Matt! Thanks for Sharing your Art with us!
Glad you enjoyed it! I appreciate you watching!
Beautiful knife. I always liked lower layer Damascus, and you did an incredible job with it in this knife. Very nice job.
Thanks! I appreciate you watching!
Thats gorgeous! Nice work.
Thanks! I appreciate you watching!
It definitely put a whole lot of work into this, good thing you had to power tools that would have taken weeks if not longer.. Thanks for sharing.
Keep looking up by for now your new friend Ken God-bless
Thanks for watching, I greatly appreciate it!
beautiful work on that MATT i love the pattern low layer damascus looks great i think merry xmas to you and your family Mark 😀👍👍
Thanks! Merry Christmas to you and your family as well! I appreciate you watching.
Thank you
Thank you for watching, I appreciate it.
Nice result, i'm currently working on a forge press design so i can get into damascus 👍
Thanks! A forge press makes it a lot easier thats for sure. I appreciate you watching.
Very nice work. Forge On. God Bless.
Thanks, you too! I appreciate you watching!
Nice knife, well done
Thanks! I appreciate you watching!
That's forging beautiful.
Nice!!..buddy beautiful knife 🔪 😍
Thanks! I appreciate you checking it out!
Nice work.
Thanks! Appreciate you watching.
Beautiful work just amazing
Thanks! I appreciate you watching!
gorgeous, what's the wood?
Thanks! It is Bocote wood. I appreciate you watching.
Increíble trabajo
Where can I buy your knives?
Beautiful
Thanks! I appreciate you watching!
So do you acid treat the demascus or does it just naturally pop the design of metal like that?
I use a mixture of ferric chloride and distilled water (regular water will work as well). I make sure the knife is hand sanded up to a high grit (I normally go up to 600 grit) I let it set in the ferric for around 5 min then take it out, spray it with windex and use a piece of 1000 grit sand paper to remove the oxides that are built up on the surface then repeat the process. I usually do this 3 times, after the last cycle use a mixture of baking soda and water to neutralize the acid. After the knife has dried I will mix a substantial amount of instant coffee with cold water and let the knife sit in it overnight, this turns the black portion of the blade extremely dark, after it is rinsed and dried off, apply oil or a wax like axewax to the blade and your good to go. Thank you for watching, I greatly appreciate it.
What tongs do you use
I use a pair of v-bit tongs and a pair of wolf Jaw tongs for 99 percent of my forging, I also keep a set of flat jaw tongs and a couple of different sized scrolling tongs. I appreciate you watching.
How much do you sell that knife for?
This knife is already gone, but when I have them availible I sell monosteel for 150 and random damascus for 275 with a sheath. Thanks for watching, I appreciate it!
Do you sell any of what you make?
I have some available on occasion, they can be found on my Facebook page, the link is in the about section of my channel page. I appreciate you watching!
What blades are you using for your bandsaw?
I use 18tpi Milwaukee brand, they seem to hold up really well. I appreciate you watching.
@@Mysticmountainforge thank you. I’ve been using 14tpi Milwaukee, but lately they haven’t seemed like they are lasting that long. Thank you for your response, and thank you for the content
No kiss block?
I use steel shims usually, I just rarely show them in the videos. I appreciate you watching.