Evinrude ETEC 40 50 60 65 - How To Change Water Pump Impeller + Rebuild Kit On Lower Unit 5006511
Вставка
- Опубліковано 5 жов 2024
- In this video, we look at how to remover and lower the lower unit gearbox on a 60 hp Evinrude ETEC outboard engine.
Then replace the water pump with a full water pump repair kit using part number - P/N 5006511 Including Impeller using P/N 0396725.
This is the same if using the chrome kit with P/N 0389145
Your series is outstanding. Just what I needed for my 90hp Etec. Wish manufacturers would learn that a video service manual would be amazing but that would be the end of dealers.
Glad it was able to help you out. I try to do a wide selection of service videos when doing outboards. I do believe people should have access to videos like this to be able to sort bits out when service engineers / dealers aren’t around.
some grease on the impeller key and shaft where the impeller sits goes a long way in preventing the impeller from getting seized to the housing. the o ring im sure popped off as you tried to put the impeller into the housing when turning, hence not showing that part. to prevent this, put some 847 permatex under the o ring groove all around let it dry for 10 minutes. a quick smear of grease will help to seal it. to prime the pump making it more efficient, turn the impeller counter clockwise 1/8-1/4 turn while pulling UP on the driveshaft. improves efficiency.
Thanks bro! Im from Brazil! Your video help me.
Glad I could help 👍 thanks for watching
Thanks very much! It helps a lot to give maintenance at my e-tec
Glad to hear it 👍 Thanks for watching!
Great video
Glad you enjoyed it
Did you have it in forward, neutral or reverse when you drop the lower? Does it matter?
It shouldn't matter as long as it all goes back the same way.
The shift will only go back together if it matches anyway, I.e Fwd & Fwd / Rev & Rev as long as you don't unwind the shift linkage or adjust it you'll be good
Do you know it’s it’s the same for the 75hp?
I suspect it’ll be a similar process for lower unit removal, but it uses a different water pump kit
After reviewing, other videos and written instructions show an O-ring used to hold the keyway/cam onto the shaft and the impeller pushes the O-ring down and rest on top of the O-ring inside the housing. Can you explain the difference?
Hi,
I’m not sure about using an o ring to hold the key way, I always use a small amount of marine grease.
The parts diagrams for the Evinrude Etec only show 1 o ring being used on the water pump and that’s for the water pump housing which is larger than the impeller.
I suppose some people may have different methods for insulation but using additional parts does come with risks especially if say using an additional o ring, it could break down and could then become trapped in the water passage ways.
Unless they push the impeller down just enough to engage with the cam and then are able to cut and remove that o ring.
You said at the end of the video, make sure it’s not in gear. So I’m assuming you did this whole job with the throttle handle in neutral?
Yeah that would be correct 👍
Basically to remove the gearshift link put the gear to which ever position is easier, believe neutral is best.
It’ll not go back together another way apart from the way you remove it in, unless you unwind or remove the shift linkage by error, as the shift linkage always matches the throttle / gear position.
What happens when the key weight won’t unlock??
Key weight ?
Здравствуйте! Скажите пожалуйста какие ещё узлы на этом двигателе требуется обслужить перед началом сезона? Интересует в частности чистка дроссельной заслонки если она есть. Заранее спасибо!)
Hi,
So generally on the Etec we would do the following.
Spark plugs
Fuel filter
Fuel lift pump
Impeller
Relief valve
Gear oil
Test thermostat
We have videos of most of these job on our “how to service a Evinrude” playlist
Please like each video you find helpful and subscribe if you haven’t already 👍
With regards to the throttle body you could try a throttle body cleaner / spray
Спасибо большое за быстрый ответ!) Все ваши видео я посмотрел и на канал подписан конечно же! Было бы не плохо посмотреть видео чистки дроссельной заслонки от вас 😊. Ещё один вопрос по маслу, если нет XD 100 каким аналогом можно заменить? Про смену в диагностике на TC-W3 я знаю)
Thank you for be already subscribed !
So Google translator might be off a little with what you're saying.
If you're meaning what can you use if you don't have any XD 100 left, you can use XD 50 or TCW3, but this must be changed on the EMM using the plug in diagnostic software. Otherwise, the engine will meter the oil in at the wrong rate, believe its from 100:1 ( fully sync ) down to 50:1 ration ( sync blend ).
Not doing this could cause damage the bearings / engine etc.
XD 100 is the best oil available to ETEC's as it has little to no smoke / soot and is used at 100:1 so uses half the oil compared to other oil, plus provides the best lubrication.
Да, я это знаю) диагностический шнур и программа у меня есть, какой аналог можно использовать взамен XD 100 ?
I'm not sure if there is an exact equivalent to XD100 as the EMM is programmed for this specific oil only as opposed to a grade?
The same goes for when it's programmed to XD50 I guess.
I suppose when programmed to TCW3 then any oil which meets that grade would be ok.
The XD100 / 50 was designed for the engine directly.
If you were to find a equivalent fully synthetic grade which isn't xd100 then you would be taking a risk for the sake of either reprogramming or just buying xd100