Mastering DSC NEO: Wireless Programming Made Easy
Вставка
- Опубліковано 7 вер 2024
- In this video, Hayden will show you just how easy it is to add wireless devices to your DSC Neo. He will demonstrate a enrolling a variety of wireless devices from the DSC PowerG. Specifically, he will show you how to enroll a PG9945 door contact, a PG9922 glassbreak sensor, a PG9936 smoke detector, and finally an HS2LCDWF9ENGN wireless LCD keypad.
This multi-part series of videos covers the DSC PowerSeries Neo line that will take you from start to finish of wiring and programming your alarm system. We will cover a variety of modules and sensors and this will be applicable to the entire Neo lineup, HS2016, HS2032, HS2064, and HS2128 PowerSeries Neo alarm systems.
We have some additional support documents such as quickstart guides available for free on our website at Http://AlarmSystemStor...
Please leave a comment if you have any questions or recommendations for future videos and we will try to respond. Thanks for watching!
Got my first install tomorrow.
Thanks!
Well done man properly explained helped me a lot
Hi yes I need to open some zone that as be close on wireless panel or me to contact my external passive hard wire
Great, now that I know how to add keypad #2. How to add wireless smoke detector #2?
Mostly what I use is DSC 832s in 1832s. Does this program very similar to it apparently they don’t make the 1832 any longer so I need to buy a neo panel for a system next week. Do you think I will have any trouble programming one of these opposed to the 1832. Thank you.
Yes it is very similar. Most feel it's easier in fact because you can see more detail in programming.
I am trying to do wireless enrollment DSC WS4936 SOME DETECTORS to my DSC NEO system but it doesn't detect it? An
Any input?
A DSC WS4936 is not compatible with the Neo. That smoke is for the prior generation of DCS wireless. The PG9936 is the correct one to use with Neo. www.alarmsystemstore.com/products/dsc-pg9936-powerg-wireless-smoke-and-heat-detector
Hello, my panic buttons aren't signaling my siren to turn on. Neither the fire, medic or panic button turns on the siren. They are all set to on. What am I missing?
How do i delete (disenroll) existing wireless smoke detectors from key pad? I am planning to upgrade to newer model wireless smoke detectors as existing ones were installed in 2007
how to program AES 3015 PSTN Receiver with DSC powerSeries Neo Alarm
Hi Hayden, Is there any way to keep the Wireless Keypad "armed light" on when the keypad is in the dark mode so that a person can see that the system is armed when they go out a door?
No, there is no way to customize dark mode for what is visable. You'd have to press a key to "wake" it to see the state.
Was the PG9862 Ceiling Motion Sensor a 915MHz PIR unit?
Same as the rest of the Power G sensors. It's a range though rather than a specific frequency.
Can i add a wireless keypad using DLS5?
Not certain, we rarely use DLS. I have used it for large systems though and I can tell you that it would take way longer to add a device or two only via DLS. We only ever used it for very big systems. I can hand program even a basic 8 zone system faster manually than I can DLS.
Are sirens wireless
how long will the batteries last for the smoke detector?
Sorry for the late response Danladi, but the batteries for the smokes typically last 3 years under normal use.
hi does this connect to a control panel? or keypad only
Does what connect?
@@andybowman9697 Does the keypad have to be wired to a board?
some are wired and some are wireless. Both are shown here, in fact the vid shows how to add the wireless one.
@@andybowman9697 Ok thanks
How to arm the alarm from DLS 5 1.7 software or from iPhone?