Sir this video would be excellent without the background music, only with your knowledge, english subtitles and the beeps of the tool! That's all we need. Great job indeed, best regards from Italy 👋
I did find I have one that beeps on both... Thanks for the video🥇. Will check on cost for replacement or another motherboard if too costly to repair.... Music a bit loud, but desperation helped me bare it🥴💃🏾
hello...would you mind if i ask...kakabili ko lng ng Gigabyte Motherboard...as i test it wala pong signal ang LAN PORT..ano po possible na deffect nito?
I urge you to use some flux and maybe remove the old solder/add new one. What you did is most likely a cold joint and won't last long IMHO. Nice video though!
for those interested on my repair. i followed his steps, since i dont have the beeper feature, i used the ohm feature of my tester and i noticed 1 pin has 0ohm resistance and 1 pin has about 100000ohm resistance for good mosfet. for bad mosfet, both pins have 0 ohm resistance. i just salvaged a mosfet from another motherboard. though not the same, it seems to work but not sure for how long
Pretty cool, music too damn loud. Hard to hear the multimeter. Got a question though. Why didnt you use flux removing the mosfet. And putting one back on.
Daaamn thank you so much bro i sent to one technician he said my motherboard got short circuit can't be repaired so buy new but your video made me to do it by myself please can you share use the tools used by you so i can arrange
I have the same problem, the fan stopped running after 4 pin is connected. But all the mosfet beep on single leg. What are others inspection should I do?
thank you for this explanatory video. i have a strix z270f which took an over voltage. only the red led (power supply) lights up. I like to do the investigation that you recommend. what is the name of the card inserted in PCI. is there a similar one for my model? what is the name of the heat gun? thank you in advance for your time
hello how are you,,, nice video very informative well done,,, i have a question a have H81 mobo, you can turn on the unit but not in the power pin of the mobo but on the terminal of the psu ( 3&4 or 4&5) . thanks
I wonder, in a video so important what is the need for background music? if the test involves listening to the short, what does that add? lowered the video engagement to 30%.
Very Good congratulation One question for the gun how much for the force of the air and how many degrees thank you very much explain I understand you better with you
Bruce Lee i use cellkit 805d, it like gordak or else, but not like hakko. I use 4 for air flow, and 4-4,5 for hot (about 330c-360c). But in high motherboard it's more hot than low med motherboard
So the open is bypassed without the CPU power plugged in. But when the CPU is plugged in it re routes the connection but ends continuity because of the open thus shutting down all power anywhere on the board.
@@apakahbisachannel4098 di indo tidak ada yg jual, ada pun biasanya beda seri. biasanya untuk board bisa dikanibal dari board lain, yg setara ukuran nya, atau kl mau baru bias order ke china langsung cm butuh waktu min 20hr kerja perngiriman.
Where I have to send my motherboard? I cannot boot into BIOS because I keep getting Memory Error LED. I tried 4 different sticks in every single slot one at a time.
@@raenanestores4510 there a code 4-5 number & letter, search on google keywoard datasheet or pdf. Read at the first page ussualy show a volt and ampere.
www.ebay.co.uk/i/233395324007?chn=ps&norover=1&mkevt=1&mkrid=710-134428-41853-0&mkcid=2&itemid=233395324007&targetid=878706529565&device=m&mktype=pla&googleloc=1006884&poi=&campaignid=9445849096&mkgroupid=104301045068&rlsatarget=aud-629407027585:pla-878706529565&abcId=1139126&merchantid=138360520&gclid=CjwKCAjw95D0BRBFEiwAcO1KDEPy4M-GYbmgik_Lyb3d1RIpXdsn9TEL3yLd4xNwaVkk3vMCD2DtwRoCaGMQAvD_BwE it's a pci voltage checker diagnostic thing
Check if all plugs and cables are firmly in. Pull all the ram and clean them with a rubber ( A pencil rubber. ) by lightly rubbing the gold contacts, both sides. Buy a new cmos battery. If nothing then it could be power. If power is known to be good then it's probably mobo short somewhere. Anything like loose screws in the case? Gently shake it, you'll hear it.
Could be a bad power supply. Also could be bad electrolytic capacitors on the motherboard. Sometimes you will see the capacitors leaking and it bulging.
Can you repair board for public? Have a project board that needs a new socket would love to see it fixed. Don't mind buying the part and paying for the time to see it fixed.
Hi, I have digital multimeter but does not have buzzer. How can I test it? What would be the measurement to say it's normal and abnormal? And you mentioned "Black probe to Ground", what ground do you mean? Is it the Ground of the mosfet itself or the ground which is located on the front panel? Thank you for your answer.
i don't have any background on electro, computer is just my hobby, since first time my father bought me at 1995 then i love with computer. from 2012 i learn by my self to repair motherboard & graphics card from any web/video i found then i develop it. the important is do not afraid to try and learn.
mosfet should be the same when I replace it flux not necessary as I see or what and hot air very enough to solder the mosfet or I can use any other ways please answer as soon as u get this *By The Way, You Did Great Job*
1. no it can be any mosfet with right channel, package and minimally tha same or higher amperage 2. flux is NESSESSARY anytime when soldering 3. u can ose hotair, infrared or laser beam. soldering is just heating
I have adding hdd on x99 lga2011-3 and after that not starting. If I remove 2x4 power to cpu,just rebooting loop,but when I put this 2x4 power it start less then seconds on every power button pressing. 2x4 connector gas 4 gnd 4x+12v, when insert one of them voltage drops to 2v,but problem is no standard mosfet transistor but has 6x ir3556 Any info how to test this integrated fets???
My PC works fine it lights up the fans spin but my Keyboard,Mouse RGB won't light up as well as my Monitor not turning on, what should i do to fix this?
Sir this video would be excellent without the background music, only with your knowledge, english subtitles and the beeps of the tool! That's all we need.
Great job indeed, best regards from Italy 👋
you wrong. with music is good....
Thanks for this quick tutorial on using the beep thing and finding faulty mosfets.
You killed it bro i appreciate a lot,,,thanks for this class... Background music doesn't affect,,instead you make me put 100% concentration
Next time please remove the background music. as long as there is captioning in english your videos are awesome.
@Gage Yousef funny how you and Adan both joined UA-cam 2 weeks ago...
Yes. Felt like i was in an 80's techno club.
Just mute it bro i did that
naaaah maaan a bangerrrr
Helped me figure out what was wrong with my MB, thanks!
I also now have a video I can put on at house parties to get everyone dancin
I did find I have one that beeps on both... Thanks for the video🥇. Will check on cost for replacement or another motherboard if too costly to repair.... Music a bit loud, but desperation helped me bare it🥴💃🏾
Great video! The music is really annoying when trying to hear the beeps.
Great video on 2023! I´m with this problem now with Maxsun A320M.2-VH, now i have an idea how to start to diagnose and look for a solution! thks bro!
Good work sir, i am addicted to these technical vedeos, i have subscribed to more than 30. I am profesional technician myself.
hello...would you mind if i ask...kakabili ko lng ng Gigabyte Motherboard...as i test it wala pong signal ang LAN PORT..ano po possible na deffect nito?
No one can concentrate on two things 100% at the same time, the music impairs the learners concentration.
Thanks anyway
I urge you to use some flux and maybe remove the old solder/add new one. What you did is most likely a cold joint and won't last long IMHO. Nice video though!
Thanks for this tutorial! I will probably be able to fix my PC that is down since several years!
great idea but hard to acquire spare parts.
thank you for this information!!!! this has literally save my motherboard. thank you
glad to hear you can repair your board...
hope you can also make tutorial for a completely no response motherboard. thank you
for those interested on my repair. i followed his steps, since i dont have the beeper feature, i used the ohm feature of my tester and i noticed 1 pin has 0ohm resistance and 1 pin has about 100000ohm resistance for good mosfet. for bad mosfet, both pins have 0 ohm resistance. i just salvaged a mosfet from another motherboard. though not the same, it seems to work but not sure for how long
@@Misterbtt
That's a good idea ... I have a couple old Mobos with parts I can steal too.
I am a fan of no music but awesome work!
Great video, but the BGM is annoying.
What if there's no buzz sound at all at some mosfets? Does it mean there's short too?
Must lower the background music at least 50% and when testing for the beep sound mute the background music and return when done testing.
Pretty cool, music too damn loud. Hard to hear the multimeter. Got a question though. Why didnt you use flux removing the mosfet. And putting one back on.
Daaamn thank you so much bro i sent to one technician he said my motherboard got short circuit can't be repaired so buy new but your video made me to do it by myself please can you share use the tools used by you so i can arrange
Where can I get the diagnostic board? Your video (except the audio ;-)) is very helpful. Thanks!
same question here!
It's called a POST (Power On Self Test) card. You can find them on ebay, amazon etc.
Hi, what if both the pins don't sound?
what is the device you put in pci lane to check during power on? i do want to buy it online. very good video. thumbs up
Post card.
it's good to see how to find the broken parts. the problem for me is where to find the replacement part
you can take it from another scarb motherboard or buy new from alixprs.
That was a great video. It was super helpful and it is exactly what is wrong with mine.
shorted , not open... open has no deflection sir. btw good video.
Mr English teacher we hear u
Remove background music 🎵
Congratulations, excellent
i have a mb that has that exact problem. gonna fix it. thanx bro.
I found few MOSFET where there wasn't a beep on both on the contrary.
sir where do the black probe connected while you are testing mosfet from red probe???
Nice 👍🏾 I actually learn something new
I have the same problem, the fan stopped running after 4 pin is connected. But all the mosfet beep on single leg. What are others inspection should I do?
Sir pwede ba ung ordinary multitester pang electronics... Kasi walang buzzer.. ?? Salamat sa pagsagot
thank you for this explanatory video. i have a strix z270f which took an over voltage. only the red led (power supply) lights up. I like to do the investigation that you recommend. what is the name of the card inserted in PCI. is there a similar one for my model? what is the name of the heat gun? thank you in advance for your time
Master kalo dah turun tangan ya kek gini (y) MANTAPSSSSSSSS
sy masih belajar bro...coz teknologi selalu baru harus dipelajari terus.
Wah ini ne yg ane demen,kek padi :D
Betul bg ... Lanjutkan terus karyanya
Sukses terus bg
thanks boss,what card you use it detect the problem?
Thank you, great video. My mobo has a mosfet that has two beeps, also near it the small thing between it and the capacitor also beep both sides.
What mode we have to set multimeter?
Very helpful video!! Thankyou so much!
Thanks for this tip! I could confirm the shot-circuit on one of the mosfets on my dead mb. Now I only need this dragon breath you used
hello how are you,,, nice video very informative well done,,, i have a question a have H81 mobo, you can turn on the unit but not in the power pin of the mobo but on the terminal of the psu ( 3&4 or 4&5) . thanks
where do you connect the +ve and -ve wire of the electronic machine tester to make it valid? I am interested..I will try to fix what's broken..
Great help for me sir! thank you for this video!
I wonder, in a video so important what is the need for background music? if the test involves listening to the short, what does that add? lowered the video engagement to 30%.
Very Good congratulation One question for the gun how much for the force of the air and how many degrees thank you very much explain I understand you better with you
Bruce Lee i use cellkit 805d, it like gordak or else, but not like hakko. I use 4 for air flow, and 4-4,5 for hot (about 330c-360c). But in high motherboard it's more hot than low med motherboard
CoRE- Fixpc thx my friend I love yur work continu
4863NG mosfet nhi mil rha h to aap koi substitute bta sakte h iska??
So the open is bypassed without the CPU power plugged in. But when the CPU is plugged in it re routes the connection but ends continuity because of the open thus shutting down all power anywhere on the board.
what if there's no beep?
bro itu transitor apa namanya ?mobo punya gw juga gitu sob tengkyu sharingnya ....
namanya mosfet analog, bukan transistor..
@@Zettabitlab kalo mau beli dimana bro ? mau diservice sendiri sekalian nyoba2 sapa tau berhasil sob...
@@apakahbisachannel4098 di indo tidak ada yg jual, ada pun biasanya beda seri.
biasanya untuk board bisa dikanibal dari board lain, yg setara ukuran nya, atau kl mau baru bias order ke china langsung cm butuh waktu min 20hr kerja perngiriman.
@@Zettabitlab ok sob tengkyu atas sharingnya sukses terus
Where did You stab the ground stick
will anny other capacitor fit it with out needing any exact description or model on the chip before replacing it 🤔
Its important to match replacement components. Any old cap or mosfet will not do.
where is flux?
its not necessary in regulator
explain John please
@@johnserrano5025 Thats total BULLSHIT
@@danielsatko- flux function is just to retain heat which you could do by constantly blow really hot air
@@erticyusa5928 u really dont know a shit.
clear ...music is loud a bit :D thanx man
What kind of soldering is that
Where can I buy one of those PCBs. you connected to the motherboard PCI port to diagnose ?
Where would you find a replacement?
Irritating music sound
background music should be low pls
nice work
its relaxing for me.😂
what if they dont give any sound?they are faulty too then?
You're awesome man!
Where I have to send my motherboard? I cannot boot into BIOS because I keep getting Memory Error LED. I tried 4 different sticks in every single slot one at a time.
What if the 4 pin are connected and its work? And if i remove the 4 pin the motherboard will immediately poweroff after 1-5 seconds?
same problem did u get fix? i think its motherboard not psu or ram. because 1-5s on and off
@@kawesayakedenkamek not yet
Where might I find the card like you are using for the readouts? What is it called please?
Michael Herbert that’s a POST card
where did you touch the negative probe ( the black stick in tester.)
Ground, you can out it on usb case, black wire psu, screw hole..etc
sir would you mind teach me how to read or to know the value of a mosfet? the printed ramdom letters and numbers at the top of a mosfet sir.
@@raenanestores4510 there a code 4-5 number & letter, search on google keywoard datasheet or pdf. Read at the first page ussualy show a volt and ampere.
thanks. i really appreciated your help.
Where is ur workshop i want to repair my motherboard
Dead mosfet? Yep.
Dead RAM slot? Yep.
Asrock? Yep.
is there a video like this but with a laptop gaming motherboard?
What if i don't have the tool that makes beep sound? Are there any tools that can be replaced?
actually is very cheap, around 3$
Thanks for the video but if there is no beep at all is it ok or not?
what you call that thing in the PCI? that can detect problems?
Can i ask you whats that thing in the PCI slot?
www.ebay.co.uk/i/233395324007?chn=ps&norover=1&mkevt=1&mkrid=710-134428-41853-0&mkcid=2&itemid=233395324007&targetid=878706529565&device=m&mktype=pla&googleloc=1006884&poi=&campaignid=9445849096&mkgroupid=104301045068&rlsatarget=aud-629407027585:pla-878706529565&abcId=1139126&merchantid=138360520&gclid=CjwKCAjw95D0BRBFEiwAcO1KDEPy4M-GYbmgik_Lyb3d1RIpXdsn9TEL3yLd4xNwaVkk3vMCD2DtwRoCaGMQAvD_BwE
it's a pci voltage checker diagnostic thing
how do you know which mosfet to replace? and possible close specs I should get like is it to get higher voltage and amp one to replace it with?
i already give how to check broken fet in this video, for votage and amp need to looking for datasheet.
What happen if a mosfet doesnt make any beep using the buzzer?
plug in cpu to the socket or measure offboard
Did you replace your CPU? or did your cpu fry during the first attempt?
What if my Mobo turn on for 1 sec then turns off? When everything is plugged
Same here !!!!
Check if all plugs and cables are firmly in. Pull all the ram and clean them with a rubber ( A pencil rubber. ) by lightly rubbing the gold contacts, both sides. Buy a new cmos battery. If nothing then it could be power. If power is known to be good then it's probably mobo short somewhere. Anything like loose screws in the case? Gently shake it, you'll hear it.
Could be a bad power supply. Also could be bad electrolytic capacitors on the motherboard. Sometimes you will see the capacitors leaking and it bulging.
Can you repair board for public? Have a project board that needs a new socket would love to see it fixed. Don't mind buying the part and paying for the time to see it fixed.
I have a question if you just take off the mosfet that has open circuit and then turn it on will it work that way ?
No way
What do you call the pci board display indicator? thank you
What is the name of the PCI card that you have connected with the LED screen?
it's a debug card
Biaya perbaikannya berapa gan klo bgini?
Hi, I have digital multimeter but does not have buzzer. How can I test it? What would be the measurement to say it's normal and abnormal? And you mentioned "Black probe to Ground", what ground do you mean? Is it the Ground of the mosfet itself or the ground which is located on the front panel? Thank you for your answer.
Ground probe is also we consider it as a Negative terminal
How did you get started doing all of this? What's your background?
i don't have any background on electro, computer is just my hobby, since first time my father bought me at 1995 then i love with computer.
from 2012 i learn by my self to repair motherboard & graphics card from any web/video i found then i develop it.
the important is do not afraid to try and learn.
@@Zettabitlab I've sub and thank you for your insight. Hope your channel grows because your style of videos are really informative.
i have a motherboard with this problem too. but motherboard starts when i change the power supply! what is the problem?
if you change power supply and it works then the issue is power supply.....
what is that diagnostic board?
What is the display board you connect?.
mosfet should be the same when I replace it
flux not necessary as I see or what
and hot air very enough to solder the mosfet or I can use any other ways
please answer as soon as u get this
*By The Way, You Did Great Job*
1. no it can be any mosfet with right channel, package and minimally tha same or higher amperage
2. flux is NESSESSARY anytime when soldering
3. u can ose hotair, infrared or laser beam. soldering is just heating
The song is from Kevon macleod-EDM mode
What's the seven segment display unit??
interesting one anyway its only demonstration , thats good friend
What if MOSFETs has no beep ?
Hi, what are these big square components above right the chip that was replaced?
EXCELENTE ,, MUCHAS MUCHAS GRACIAS,, MÉXICO CDMX
bro whats the name of the digital display tester you insert in motherboard slot?
PCI Voltage Checker Diagnostic ?
hi can i use other multimeter if yes which one got Buzzer? thanks
ur vdo is suprb but please slow background music
we cant listen buzzer sound from meter and
where is you black wire of meter?????
must reply
Black wire attached to GROUND , NEGATIVE
I have adding hdd on x99 lga2011-3 and after that not starting. If I remove 2x4 power to cpu,just rebooting loop,but when I put this 2x4 power it start less then seconds on every power button pressing. 2x4 connector gas 4 gnd 4x+12v, when insert one of them voltage drops to 2v,but problem is no standard mosfet transistor but has 6x ir3556
Any info how to test this integrated fets???
great demonstration。 thank you.
My PC works fine it lights up the fans spin but my Keyboard,Mouse RGB won't light up as well as my Monitor not turning on, what should i do to fix this?
What if both tail of mosfet have no beep?
Cool man, thanks :)
Are the gloves you are wearing special? like anti-static or such?
Regards
Just wear an anti static wriststrap.
its helpfull, but dont know where to buy exact vrm