Thank you for the video. This particular flight controller (Pixhawk 2.4.8) does not provide power to its servo rail. You need to BEC the servo rail and apply a combination of a diode and a capacitor to the rail to smooth out any voltage fluctuation and protect your flight controller. Regards!
this is definitely not what meets the eye.... you are not showing it in detail as it is impossible to trigger a sugar cube relay of 5V using a Pixhawk power rail. could you mind explaining the steps in further details?
im already explained in detail watch the video properly without skipping it and give the external 5v to relay if your controller has stable 5v supply you can give it from same
The Voltage Output of Pixhawk Pin out is Only 3.3V, not even 5V, so how do you use high voltage relay here?? This isa bit confusing, as you mentioned that we can use any relay board, I have checked the output voltage (of the Pixhawk pin) is Only 3.3V !!! Please clarify.. Tks
1st u checked output voltage of pixhawk is 3.3v but the power is given to pixhawk by USB In my video I'm connected signal wires of ESC that gives 5V To pixhawk externally so I can use any relay board those works on 5V supply
Hi bro I'm doing project on drone at first i have used the Arducopter the issue i was faced is that it was not stable it was lifting up vertically but while lifting vertically it was moving right and left without any movement in direction channels and now I'm using Pixhawk flight controller and the Same issue i am facing with Pixhawk also. So please can you help me in stabilization of drone using Pixhawk
Check your body weight is exactly equal in all direction .like if you are making Quad copter then check all 4 directions arms has equal weight Also check Motors are fitted properly If they creat ani Vibration it also unstable Also Check Propellers And battery is set to the middle of drone body
@aredits7311 Hi bro, I saw your comment and i am facing with the same problem. Did you solve your problem ? If that so can you please tell me the solution ?
Thank you for the video. This particular flight controller (Pixhawk 2.4.8) does not provide power to its servo rail. You need to BEC the servo rail and apply a combination of a diode and a capacitor to the rail to smooth out any voltage fluctuation and protect your flight controller. Regards!
you use a 3 volt or 5 volt relay?
I followed your steps in the video but the signal pin is always giving high signal the coil is energized every time
@@rashedabouali9206 check In ardupilot software may be u missed something there or try using other Relay
dude what happened to your left thumb 1:53
sir Pixhwak flight controller problem help
this is definitely not what meets the eye.... you are not showing it in detail as it is impossible to trigger a sugar cube relay of 5V using a Pixhawk power rail. could you mind explaining the steps in further details?
im already explained in detail watch the video properly without skipping it and give the external 5v to relay if your controller has stable 5v supply you can give it from same
The Voltage Output of Pixhawk Pin out is Only 3.3V, not even 5V, so how do you use high voltage relay here?? This isa bit confusing, as you mentioned that we can use any relay board, I have checked the output voltage (of the Pixhawk pin) is Only 3.3V !!! Please clarify.. Tks
1st u checked output voltage of pixhawk is 3.3v but the power is given to pixhawk by USB
In my video I'm connected signal wires of ESC that gives 5V To pixhawk externally so I can use any relay board those works on 5V supply
Not working ! Please help
Hi bro I'm doing project on drone at first i have used the Arducopter the issue i was faced is that it was not stable it was lifting up vertically but while lifting vertically it was moving right and left without any movement in direction channels and now I'm using Pixhawk flight controller and the Same issue i am facing with Pixhawk also. So please can you help me in stabilization of drone using Pixhawk
Check your body weight is exactly equal in all direction .like if you are making Quad copter then check all 4 directions arms has equal weight
Also check Motors are fitted properly
If they creat ani Vibration it also unstable
Also Check Propellers
And battery is set to the middle of drone body
@aredits7311 Hi bro, I saw your comment and i am facing with the same problem. Did you solve your problem ? If that so can you please tell me the solution ?
can u please help me put how to connect aux to remote control
❤️
I have followed every steps but not working for me... please help bro...
Check your relay board
احسنت
For me my relay stays on. I can not switch it of
Check the relay board I'm using
Same problem ..have you got the solution for it?
In standard parameters check relay no. That u used and change the initial state of relay
I tried and I met a trouble. It can be contorl with rc radio and the led on reley can open ,but the relay can't work actually.
try to check Standard parameters
🔥🔥
How to trigger relay during mission at particular way point
I'll showed in video In a transmitter there is separate key to trigger relay watch video properly
@@prasadbargode7169 actually I was asking about automatic triggering during mission, not to control through tx
No automatic trigger is not possible for it
But I'm trying to make it happen in another way
Price of. The pixhawk
Unpredictable
Sir ye hamare pixhowk se ho nhi rha
Watch complete video without skipping
It will definitely work
sar aapke number pixhwak flight
controller problem
I tried doing this but it did not work 😕
Please help
Just tell me what problem you facing?
Follow the steps in video I shown