Did you design the vertical back pieces where your power cord plugs in? I looked at the original build on thingi and didn’t see print files for any vertical back pieces. Very nice build by the way!
are you using a y plate BLV? can the right and left rear decks be fitted with a stock y steper motor mount? i'm planning to convert an ender 3 v2 by chance I'm currently using a BLV kit on an ender 3 v2
I don't understand your question, yes it's a blv kit with the original steper motor mount if that's what you want to know if you want to do the Voron Switchwire mod, I advise you to do only the XZ axis, the y axis can remain that of the blv, it works fine, no need to modify it
@@lanypuspasari1868 yes it is visible with its cyan blue under the bed : live.staticflickr.com/65535/52083182021_e7dac0f763_c.jpg www.lesimprimantes3d.fr/forum/topic/48110-ender-3-pro-passage-en-switchwire/?do=findComment&comment=499743 before I had the mod blv
hotend : Sunon Maglev MF40102V2-A99. Part fan : Hk Fan 5015 or GDS Fan or Sunon Maglev MF50151VX-A99 on the video it's a GDS Fan, but it depends on what I have in stock, anyway a 5015 sounds loud, but I find the most effective the hk fan (personal, others prefer the gds) the Sunon is good obviously, but much more expensive PSU ender 3 : Sunon Maglev MF60152V2-A99 Mainboard electronic : Sunon Maglev MF60152V2-A99 (I don't remember if for this one I reduced the power)
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Is the stealth burner head too heavy for the Switchwire ?? How has been your experience so far with it.
Did you design the vertical back pieces where your power cord plugs in? I looked at the original build on thingi and didn’t see print files for any vertical back pieces. Very nice build by the way!
Hello, how much did this modification cost?
are you using a y plate BLV? can the right and left rear decks be fitted with a stock y steper motor mount? i'm planning to convert an ender 3 v2 by chance I'm currently using a BLV kit on an ender 3 v2
I don't understand your question, yes it's a blv kit with the original steper motor mount if that's what you want to know
if you want to do the Voron Switchwire mod, I advise you to do only the XZ axis, the y axis can remain that of the blv, it works fine, no need to modify it
@@simrtech3d I mean are you using Y plate carriage BLV?
@@lanypuspasari1868 yes it is visible with its cyan blue under the bed : live.staticflickr.com/65535/52083182021_e7dac0f763_c.jpg
www.lesimprimantes3d.fr/forum/topic/48110-ender-3-pro-passage-en-switchwire/?do=findComment&comment=499743
before I had the mod blv
What fans are you using? For hotend, part fan, mainboard and PSU. I assume all were changed, because the printer is very silent.
Great job ;)
hotend : Sunon Maglev MF40102V2-A99.
Part fan : Hk Fan 5015 or GDS Fan or Sunon Maglev MF50151VX-A99 on the video it's a GDS Fan, but it depends on what I have in stock, anyway a 5015 sounds loud, but I find the most effective the hk fan (personal, others prefer the gds) the Sunon is good obviously, but much more expensive
PSU ender 3 : Sunon Maglev MF60152V2-A99
Mainboard electronic : Sunon Maglev MF60152V2-A99 (I don't remember if for this one I reduced the power)
@@simrtech3d thanks. Going to take a look.
can you give a link to the seller of the stepper motor like the seller you use?
You can go ahead with the 40mm smaller ones as per specs, but I'm using these ones. More torque, less heat, no missed steps
what do you use to raise the z . axis?
i use Voron Switchwire XZ Gantry
@@simrtech3d where can i get it?
@@anhtai_8828 you build it yourself with the voron switchwire guide or the ender 3 to switchwire guide
My direct drive ender 3 prints twice as fast as this. What is the point?
this video shows an ender 3 pro which is switched to switchwire and it still had to be adjusted, I don't see why you are talking about speed?