Це відео не доступне.
Перепрошуємо.
Bradley smoker, how to replace bisquettes
Вставка
- Опубліковано 3 січ 2021
- Size of washers
Diameter: 57 mm.
Height : 1.9 mm-1.8 mm.
Wall thickness, 1.5 mm (or less).
Food grade foil
You do not need to use a diameter greater than 58.5 mm. Since we wrap the washers with foil, the diameter increases. And this can lead to jamming it on the heating element. and you will have to correct it manually
The container holds about 10 grams of wood chips. Knowing the weight, time spent on wood chips and the cost of wood chips, you can calculate the cost of using this method. In my case, it's 4-7 pounds in 24 hours. It all depends on what price you will take wood chips.
To facilitate your calculations, you spend 1200 grams of wood chips per day of smoking.
Of the inconveniences, what you need once an hour or an hour and a half, get the waste containers out of the bowl.
Velmi chytré řešeni . Děkuji . Mirek Praha
I dont speak spanish but I understand your idea. Its great. Ty
Thanks USA
Thanks from denmark 💪😊🦌
Great idea thank you :-)
Well done
Great idea!
Вниз можно ложить более мелкую щепу и будет дым быстрее
Здравствуйте
Подскажите пожалуйста, а фольгу вы каждый раз меняете на кольцах?
Приветствую.
Нет. Только когда порвется.
Добрый день,решил приобрести коптилку этой марки , вопрос при установке в квартире с отводом в вытяжку сильный ли запах будет или она герметичная?
Приветствую. Если вытяжка будет, то не сильный запах. Но нужно учесть, что при открытии дверей, вытяжка не справится.
Коптильня хорошая. Но помните о проблемах с бисквитами. Это самый дорогой расходник.
Посмотрите на польскую, такого же плана. Но у нее шнековая подача опилок.
Привіт ТАГІР. ЧУДОВИЙ РОЛИК. ДЯКУЮ ЗА ВІДЕО БУЛО ЦІКАВО. З НОВИМ РОКОМ ВСІХ БЛАГ. З ПОВАГОЮ ПАВЛО. М.ЛЬВІВ УКРАЇНА.
Взаимно
Excellent thanks, stainless rings or aluminum? Canada
aluminium rings/
@@vintagerazors I noticed you didn’t have any water in the Aner that catches the rings? Is that correct?
@@blueback21 Yes. There is no water in the bowl. They were just experiments. You can pour water. You can do it dry. Then the chips will still burn out.
I don't use it now.
Right now I'm using a labyrinth smoke generator. And I use pills from America in it.
.
@@vintagerazors brilliant
Ну а если не делать металлические формы а поставить сразу необходимое количество в одной емкости.Такое возможно?
Не могу сказать точно, но наверное нет. Может воспламенится.
Значит нужно пробовать.Будет медленно сгорать не успеет воспламениться.Ресь не идет о 100г расходника
Здравствуйте. Какой мощности у вас нагревательный элемент для брикетов?
У меня 125 ватт, в интернете посмотрел они вроде все по 125 ватт. Клечки с фольгой не успевают практически задымится за 20 минут. У меня скидывает через 20 минут, на час нужно 3 бисквита. А у вас как я понял на час 5 штук?
Приветствую. Нагревательный элемент был стандартный.
Может фольга слишком толстая?. У меня была, очень тонкая.
@@vintagerazors тоненькая пищевая фольга
@@user-og6hz7dw3u может щепа крупная?
Здравствуйте. Какой материал трубы?
Приветствую. Это была алюминиевая труба. Для эксперемента , она была самая дешевая.
The final in an email chain of disappointment with Bradley
After applying a lubricant/rust dissolver to the screw I was unable to remove it. The screw slots gave out. Now the screw head must be ground off. At this point I do not have enough screws to fully reassemble the bisquette heater.
When I spoke to Olev and asked him what the dimensions were for those screws his answer was that he would have to research that for me, and he would let me know. I have not heard from him. The local big box and hardware stores carry nothing identical. The choices there are either slightly too large or too small, and in that small size only Imperial is available here. I think the dimensions must be Metric and I need those dimensions in order to purchase replacements online.
I am going to order stainless steel screws and replace all the rusted screws in the P10, which is almost all of them. Please, at least give me the correct screw dimensions.
In the picture below you can see that the bracket holding the heating wires is badly corroded. I understand you will not replace the entire heater assembly, but would you at least replace that part?
I am going to fully disassemble the bisquette heater, grind off all the rust, and repaint it with a heat tolerant rust resistant coating. I’m also going to examine the drip pan to try and understand how drippings got inside that heater in the first place since it is unreasonable to have to disassemble that part of the P10 to clean up what should not be there.
That concludes my request for help, and my information for you regarding repair of this unit.
MESSAGE FROM A VERY DISSAPOINTED CUSTOMER
I have used Bradley smokers for over 40 years. My first was an aluminum model that eventually had to be replaced. I’ve purchased several to give as gifts to others. I am as loyal and long term a customer as Bradley could hope to have.
The treatment I have received from support has been unpleasant. I’ve been accused of mistreating my P10 by support, then later had Olev confirm the screws were a bad choice that will be replaced. Now I’ve been accused of not properly caring for my P10 because I did not disassemble the heater to clean it. That procedure is not called for in your manual and should not be needed.
I will never again purchase a product from Bradley. Not because my P10 has problems, but because Bradley support tries to blame the product problems on me, and refuses to acknowledge and replace that which is faulty.
My entire interaction with Bradley has been fully documented in pictures and email. Take a moment to examine my UA-cam page and the videos I have there. They are detailed and have good reviews. I will be adding a detailed review of my experience with the P10, showing the rust throughout, the magnets sticking to what is claimed to be stainless steel, and the emails from support trying to blame me for those defects. Although my videos only get a up to 40,000 views, there is not much on UA-cam discussing the P10, so I expect my video will be easy to find if people research the P10 prior to purchase.
Because you are not going to correct the deficiencies in your product I am going to alert prospective customers to them. Most disturbing to me is that Bradley intends to keep shipping P10s with steel screws until November when the first run of P10s with stainless screws is expected. Are you planning to send everyone a set of new screws and tell them to replace them. Such would be a good policy for those of us who already have our P10s, but shipping out units with steel screws when you could easily procure and replace the screws in your inventory units is just unethical.
Like rust, the rot in a company comes from the top and works its way in. It saddens me that Wade Bradley has so little interest in his customers that he has chosen not to engage with me when I asked courteously that he do so. Leaders who shield themselves from disappointed customers, hide behind low tier technical support and refuse to acknowledge product deficiencies eventually pay the price. Word gets out, sales drop off and they no long have a company to lead. Good luck Wade, that is where you are taking Bradley.
Bendrix Bailey
Bendrix Bailey - UA-cam
My guiding service - lots of client contact
Northeast Woodlands Guiding
Hello.
Add a video on your problem to your channel.
Whatever your post, it would not be empty.
Тагир пора говорить не у них, а у нас))... приветствую!
Приветствую :)
Норм штука. В Украине вроде не продается...
Если бы не нашел этот способ, то взял бы шнековый. Там нет большой привязке к щипе.