Awesome video. Currently dealing with CAN issues on my 2010 ML350 Bluetec. Very similar car. However, mine has 3 distributors at the passenger side footwell, not 2. 1 of them has green wires (I'm guessing drivetrain) while the other 2 have orange/brownish wires. I'm wondering which CAN that third distributor is for...
Where did you connect the negative lead of the multimeter?Is it on the battery negative terminal or any chasis ground point before taking measurements? Thanks.
Heloo my R350 2007 have a problems #,no can data was received from control module trasmision control ,buat THe car run okay no problems ......what should i check ....? Thanks again
Hello. I saw that you replaced the CGW of one model with a different one. Can you use CGW with different numbers than the original? Is it necessary to reprogram the new CWG? Thanks
My 06 e350 has no power going to the fuel pump. Fuel pump went bad so I replaced it, but now no power going to it. Relay and fuse are fine because there’s juice going to the sender, but not the fuel pump. Fuel tank is empty because I had to clean it out because of all of the dirt in it. The central gateway is new too. Replaced about a yr. ago
Awesome diagnosis. Enjoyed watching and learning. I have a 2006 R350. So this is very helpful.
Thank you so much for posting this fantastic video, please post more, Huge respects 🙂😇
Did you have to program the new central gateway module
I like the way u detaily explain things
The lecture was excellent
Awesome video. Currently dealing with CAN issues on my 2010 ML350 Bluetec. Very similar car. However, mine has 3 distributors at the passenger side footwell, not 2. 1 of them has green wires (I'm guessing drivetrain) while the other 2 have orange/brownish wires. I'm wondering which CAN that third distributor is for...
You are good man
Hi beautiful job can we done this program by Autal mexys scanner tool?
Thank you 🥋
You’re awesome!
Did you have to program the central gateway?
Awesome video
Great job
Please show the steps to get access to the gateway as there are many layers of hard plastic that don’t come off to get access to gateway in 2007 gl450
When you replaced the central Gateway, did you clone the old gateway?
Diagnostic wont communicate with engine transmission or ism dealer says i have tons of can codes is the central gateway most likely my problem
Did you manage to sort this ?
@@kunalrana3625 ya i had someone scam me who never programmed any of the modules i just need some modules programmed
Did you sort this out?
Hi... what was the solution?
@pmo3448 someone scammed me and didnt program my modules
Where do you connect ground wire from a multimeter ?
Where did you connect the negative lead of the multimeter?Is it on the battery negative terminal or any chasis ground point before taking measurements? Thanks.
I think they connected them to any chassis ground point. But if you're measuring the waveform, a solid ground like battery negative would be better.
@@Teddy-re6nv Thanks Pat.
Heloo my R350 2007 have a problems #,no can data was received from control module trasmision control ,buat THe car run okay no problems ......what should i check ....? Thanks again
Hello. I saw that you replaced the CGW of one model with a different one. Can you use CGW with different numbers than the original? Is it necessary to reprogram the new CWG? Thanks
Any ideas what u110b code is for meecedes r350
My 06 e350 has no power going to the fuel pump. Fuel pump went bad so I replaced it, but now no power going to it. Relay and fuse are fine because there’s juice going to the sender, but not the fuel pump. Fuel tank is empty because I had to clean it out because of all of the dirt in it. The central gateway is new too. Replaced about a yr. ago
Will this be the same in a A220 amg ?
I mean the software name please?
Hi, do you need to reprogram CGW or just buy used same model plug and play?
Hi. ok what if my obd2 reader isn't workknv how to fix plz. But my guse is not blow
What is you replace that controller and have the same issue? I replaced the controller, what’s the next step?
Just like me i work like you
Great!
Hi i have a b200 w246 where can I find the central gateway please help
Tôi có thể mua cái máy test đó ở đâu? Cam on
Master, teach me kung-fu.
This was xentry programming and diagnostic tool
HI I have a 2015 SL 400 cant shift out of park can you tell me where the white CAN distributor resistor is located
Under passenger seat
I have a 2006 Mercedes r350. It did not start. I replaced the ignition and its computer. I could start it, but the gear does not shift.
what can I do?
Take you sir
Where is the water come from please
am having problema with my fan. 012 C 300
👍👍👍👍👍
Can i join the technical group of you people if yes then plz send the number or link thanks to everyone who reading my msg regards.....