Convert Cisco Access Point from Lightweight to Autonomous / Standalone
Вставка
- Опубліковано 22 сер 2024
- #Cisco_AP #Conversion #IT_Support_People
Step by Step Process Converting Cisco Aironet 3600 Series Access Point from Lightweight to Autonomous version.
Requirements:
1.TFTPd64 Server
2.Cisco IOS Software AP3G2-K9W7-M for (C3600 Series AP)
3.The Cisco AP and the Laptop with TFTP server must be in same network.
According to my network setup
Lightweight AP BVI1 IP address is 192.168.1.4
Laptop's IP address where TFTP server is installed 192.168.1.7 [Default Router IP]
First disconnect the Ethernet cable from the AP then Press the Mode button and Put back the Ethernet cable to the AP and hold the Mode button Until flash light turns to umber and Once the Lightweight AP goes to online then apply the following commands to convert it to Autonomous version:
set IP_ADDR 192.168.1.4 [According to my network setup]
set NETMASK 255.255.255.0 [According to my network setup]
set DEFAULT_ROUTER 192.168.1.7 [According to my network setup]
tftp_init
ether_init
flash_init
tar -xtract tftp://192.168.1.7/ap3g2-k9w7-tar.153-3.JH.tar flash:
dir flash
set boot flash:/ap3g2-k9w7-mx.153-3.JH/ap3g2-k9w7-mx.153-3.JH
set
boot
==========================
IT Support People Facebook Page:
/ it_support-peopledeskt...
Link for Other Related Videos and necessary files:
Configure Cisco Access Point Standalone/Autonomous using GUI with WPAv2 Authentication Key:
• Configure Cisco Access...
Configure Standalone Cisco Access Point from CLI with WPAv2 Authentication:
• Configure Cisco Access...
Configuring Cisco Router to Access Internet through ISP Home router:
• Connect Cisco Router ...
Configure VLAN | Allow VLANs to Access Internet
• Configure VLAN | Allow...
Connect Cisco Router using PuTTY & Console Cable | Change Text Color/ Font Size/ Background on PuTTY:
• Connect PuTTY with Cis...
Reset Cisco Access Point to Factory Defaults using Mode Button:
• Reset Cisco Access Poi...
Download Link for TFTPd64 Server:
tftpd32.jounin....
Download Link for IOS image of Cisco Aironet 3600 Series Standalone Access Point (AP3G2-K9W7-M):
drive.google.c...
Covered Topics:
Lightweight to Autonomous (vice versa) Conversion,
Converting Cisco Wireless Access Point from Lightweight Mode to Autonomous Mode and Vice Versa,
LWAPP to Autonomous Conversion and Vice versa on Access Points,
How to convert a Cisco AP from Lightweight to Autonomous (CAP to SAP),
Convert Cisco Lightweight AP to Autonomous,
Access Points Light Weight to Autonomous Conversion and vice versa,
convert lightweight to autonomous 2700
Cisco 3602i autonomous image download,
Cisco AP standalone mode,
how to check Cisco AP is lightweight or autonomous,
autonomous AP IOS software download,
Cisco autonomous AP configuration example,
autonomous to lightweight mode upgrade tool,
Cisco AP lightweight vs autonomous,
Download IOS image AP3G2-K9W7-M for Cisco AP,
Converting a Cisco AP from LWAPP to Autonomous mode,
How to convert Cisco air AP from CAPWAP to autonomous,
Years later, STILL hands down THE BEST tutorial on how to convert an AP. Worked perfectly. Thank you good sir!!!
I used this video in combination with one other video and got it to work on a 3702 AP. I ran into some issues after I got the file downloaded to the AP from my TFTP server, it kept booting the K9w8 image, so I ended up formatting the drive and then downloading the file to the AP again. That way since it was the only OS on the drive there was no confusion. Finally got this thing converted to an Autonomous AP. Thank you so much, this video is gold.
Great video and your narration makes it like gold! Thanks!
You helped me to solve my problem on how to configure my Access point, you are the best and this is a real way of learning showing the actual set up the networking. I wish next videos with the firewall setup and Microsoft windows DHCP server. Thank you very much, Sir.
Thanks for watching... Much appreciate your suggestions.
Thank you! Finally I can see how to connect the cables properly. A friend gave me an AP1141 with no instructions, and not even the online manuals explain the wiring
Thanks for watching...
Did u use console
@@rameesali6014Hi Ramees, it's been so long ago that I can't remember what I did, sorry about that :)
Great work, king!
Keep it up!
p.s - flash file also worked for 1700 series ap
Works, but I have to suggest something to Linux users. Use Screen instead of Putty and use a PC with a serial port built-in or a USB dongle that is on Amazon ( it will save you some headaches when connecting to the AP). Also don't forget to format 'flash:' because if you have another firmware installed that is more updated it will defaults loading the one with a higher version number.
Great tutorial! Thanks to this video I converted my AIR-LAP1131AG-E-K9 to an autonomous AP! Thank you
This is great stuff bro. I have been trying to do this for the longest while man
Thanks , It worked for me and my AIRNET 3602E is up and running. Great video and info
Search and search the web and finally you gave me the solution, I just need to buy the converter
Thanks for watching
I manage to convert 1700 AP to standalone thank to this tutorial
Sir kindly share the standalone ios for 1700
Thank you very much, very good Video! For people in business environments, check your Firewall settings on your PC. It might block the TFTP programm.
by god yaar gajab vdo banaye ho, kasam se maza aa gaya
It is really great video, I was able to convert 4 AP's thanks you for sharing the information
Thanks for watching...
Thank you for sharing the information, it helped :)
Hello, I would like to know how to convert the AIR-CAP2702I-Z-K9 DE Lightweight access point to Autonomous, as I can't download autonomous firmware. I am Brazilian and would like your help.
Can you keep making videos like this !
I just added 3 new Exterior AP with diff Mac add. Im trying to configure them remotely
thanks , You helped me to solve my problem .
hello friend I have an access point AP2802e and I get this error in PUTTY: Waiting for uplink IP address and reachable default gateway.
can you help me please thank you very much.
How does the Home Router comes into play here? Why would I need the router when I can just plug directly into the PoE injector and from the injector into the AP with both devices statically configured. Why not do it that way?
Very Helpful.. Thank you!
Great assistance, same process works for the 3702
Yes...
Hey bro, by the same process did you use same image or was it a different IOS image you used?
@@Maxxypants another IOS image from Cisco page
Rolando, would you happen to have IOS image for Cisco aironet 3702e? I can't seem to download from cisco page at all
@@Maxxypants Did you ever get this image?
Awesome job brother thanks so much
You helped a lot, thanks!
Thanks for watching...
Thank you so much, its working fine with 2702i-e-k9
Thanks for watching...
I have 2702i-r-k9. Is it works with the AP3G2-K9W7-M firmware from this video?
Thank you so much.. It worked for me..
Amigo eres INCREIBLE... muchas gracias... lo único que no pude ver fue como realizaste la conexión del cable de consola a la laptop y que tipo de conectores usaste, aparte que versión de windows usaste, yo no se nada del tema tengo un equipo AIR LAP 1131 AG A K9 y quiero usarlo para mí casa, espero poder hacer todo esto con la ayuda de tú VIDEO. Gracias...
Thanks for the video. Great Help
Do you have the autonomous image for Cisco 2802I-E-K9?
I followed the steps shown in the video, but when I type "format flash:" ("AP64f6.9d00.9870 # format flash:") it fails "% Invalid input detected at '^' marker." The '^' character points to the "o" of the "format flash:" command line. Please show me what to do? Thank you very much
I had the same issue. This command cleared it for me:
delete /recursive /force flash:
Thank god for comments like this otherwise id be stuck also becuase I could not find this anywhere@@davidkemp3408
Thank you so much for this break down, but i wish to ask if it is possible to convert multiple LWAPP at once
Thanks bro.. It was helpful
Thanks for watching.
Great video, good job! I could not find in the video where you gave the link to download the ios image for the conversion to autonomous AP as promised. Can you help give the link, please?
When I send the command line the console return error syntax mark ‘^’
I’m stuck!
Why?
Thank You
With some very minor tweaks I used this to flash my 2702i to autonomous. Minor like the formatting of the flash, otherwise this was perfect.
Hello do you have use this .tar to flash 2702 i ?
Thank you very much.
Muchas gracias... exelente...
What would be the cause f this error,. I have directly connected the AP to my PC. Read request for file . Mode octet [05/01 19:09:18.560]
Using local port 57127 [05/01 19:09:18.575]
File : error 10054 in system call recv An existing connection was forcibly closed by the remote host. [05/01 19:09:18.622]
DO NOT FORGET TO TURN OFF WINDOWS FIREWALL
otherwise you get connection time-out
Merci ! Excellent !
Is it possible to use this movie for Ap AccessPoint AIR-CAP3502I-E-K9?
After installing the firmware the gui is not loading, any idea why? I have reset ad repeated the process, used also an older version of the firmware. Still no gui interface.
Hi guy! Very nice tutorial ! Can you advise where can I get the Aironet 1600E series autonomous firmware? Thank you!!
I followed these steps, however, tftp failed and now I can't boot the unit, after setting the network parameters AP is not pingable, any thoughts. Looks like I must not format the flash
Hello. Thank you so much for video.
Do this instruction and IOS image suitable for AIR CAP 2702I-E-K9 access point? If not, could you, please advise where get needed IOS image. Thank you in advance!
Excellent and helpful , please can you send me link to download the the soft ware use to convert
Hello, I'm using serial usb cable where USB-Serial ch340 drive is installed, but putty just gets black screen. Will this cable work or do I have to buy another one that has a cisco drive?
Hi, great video! Would this also work with the 3702I-E-K9?
Thank you so much
Thanks for watching
Is there any chance that you will help me remotely setup 2 x 2702I-E-K9 access points ? thanks in advance !
Need help
Screen is blank after connecting access point with console cable in putty
I need to replicate this on my Cisco AP. Where can I get the firmware for the air-lap1142n-a-k9 ? Please help me.
Very nice video! Would it be possible to get the standalone firmware for AIR-CAP3502I-E-K9? Thanks.
was very helpful
I got a used Cisco AIR LAP-1042N-N-K9, and i followed what you told, but when i open the listed COM port in putty, nothing happens, all i get is blank screen, can you plz help...
putty shows ap: show_ether shows interface is up, however not able to pin the IP from other devices
Great post. Is it possible to have the autonomous firmware for AIR-CAP1702I-E-K9 (ap3g2-k9w7-tar.153-3.JD.tar)? Thank you in advance.
Do you have the firmware for the 2600i AP for autonomous? Thank you sir
What happens when we connect straight cable instead of crossover cable.
sir i am unabale to download cisco 1532e autonomous ios .as i have no permission to download. can you help me and download this file for me and send me
Dear sir upload kindly video How to install module in cisco layer 2 & 3 router no one video available on youtube with real cisco router, how we can install module in cisco router layer 2 & 3 like serial cable module & other module Like wic card installation in cisco router layer 2 & 3 & other modules installation in cisco router
Thank you very much for this tutorial. But where can i find for more types of AP`s of cisco
?
Thanks for watching
Dear please tell me how to configure AIR-CAP2702l-E-K9 cisco access point setting. I try but it's configuration not display.
yes
Create a video on VLAN setup with Multiple SSID on Autonomous AP.
I have 3702i can we upload ios of 3600 to 3700? Unable to find specific one for 3702i
will be grateful for your reply.
i want to convert cisco aironet air-cap3502i-n-k9 light mode to stand alone ap. plz provide standalone firmware
where does the console cable goes.?
Great! Really helpful.
I cannot succesfully load the firmware via tftp...i guess it could be a reachability issue.
One question: when the AP is in ROM mode, is it able to respond to the ping? Because if i ping it from the tftp server i receive no response...
ok, i solved, it was a switch issue
I have same issue, can not connect to TFTP server. how did you figure out?
sorry mate, i don't remember how i did it@@bruce9600
can you share Industrial Wireless 3702 Access Point Autonomous AP IOS Software
this video is very helpful to learn how to do this but i am facing a problem i put username then enter once i put password i cant type there password , can any help
excellent my friend
Thanks for the tutorial video. Would you have the download location for image of AIR-CAP1702I-Z-K9, please?
Thanks for watching... Sorry I don't have
Hello,Can you please help me clear with format flash: and del /recussive /force command ?
Did you use 24v or 48v for the PoE Injector?
Great videos, I am looking for the autonomous firmware for a AIr-CAP3702i-A-K9. If no one has it, do you know where I can get it? I can't download from Cisco.
Hello. Thanks in advance . Any hope for CAP702I ?
(AIR-AP1832I-C-K9) Connected console port, press mode button, power up the AP, release the mode button after 23 sec, all is doing well but AP name is not changing. Means may be, there have some another issue. So, can you help to reset it completely as default?
This image will also work for Cisco Aironet 3700 Series?
After autonomous ，whats the running internet’s speed test,
Hi will the file you share also work with ap1260? I can see that the older versions were compatible with it
Anyone else run into a 404 error when applying the settings in the webGUI?
Masud sir,how are you?
can you some help me
I need cisco 2602i, autonomous k9w7 iso pls share your google drive.
Hi great video - question is where I can get autonomous AP os - some one could help me, please?
Hi, is the image for I (integrated) and E (external) same?
Could this method also work with a Cisco 2802i-B AP?
How to convert standalone mode AP 1700 series
Can I have IOS image of Cisco Aironet 2700 Series ?
I have AIR-CAP2602I-A-K9 model . I would like to convert Standalone Access Point. Please share link for (Aironet 2600i Access )
Thanks
Buddy waiting for some more new videos.
Thanks for watching...
Hi great video. can you help me with the file for c1700 autonomous firmware
Hi Massoud, I need to convert the AIR-CAP3702E-A-K9 to autonomous mode. but I can't find the file to do so and it requires a Cisco account that I do not have. do you have or can guide me to a link to download. thank you... any extra information is appreciated.
Cheers
i am looking for Cisco Air -Cap2702E-S-K9 autonomous firmware can anyone help
Can you help me to download the software, I can not download it. Thanks
Hi, thanks for the video, do you have firmware for CAP2602i please
Hello , i have followed the video and it is the besti have seen on the net , however can you offer some help on the below error i receive - Premature end of tar file structure . i am using the image that you have linked and also the AP is aircap 3702I aironet 3700 series .
hi. were you able to solve the issue? Can I use this firmware for 3702i?
thanks bro
I can do with 1602i cisco ap. Thank you for helping.
I don't think you need the poe injector because your home router is already poe.
Thanks for watching... My home router is not POE.