You will get inacurate with this kind of method. To get accurate alignment, You must connect both shaft with install the coupling bolt and turn simultanously between driven and load shaft. Good luck
sir pehla dial ka bara tu bathain.ye 90 nova kaya ha.dial ka 100 divisions hain so least count ho ga=1/100=0.01mm yani dial ki 1 div equal ha 0.01mm.or is main ju graduations hain jaisa 0 10 20 30 40 50 60 70 80 90 or phir zero. ye hain 0mm or 10x0.01=0.1mm phir 20 equal ha 0.2 mm or is tarha so on ye 85 ju ap na parha ha ye 8.5mm nahi bhai jan ye 85x0.01=0.85mm ha ok sir. top reading +bottom reading=side reading+side reading is sa hum 3rd reading ju support ki waji sa na par sakhain us ko maloom kar saktha hain.correct me if i am wrong
Rim-and-Face alignments should be performed with the coupling intact. Running the dial plunger across the opposing coupling surface without rotating that surface with the mounted dial indicator is about as inaccurate as you can get. www.petersontools.com
Very good job
You will get inacurate with this kind of method. To get accurate alignment, You must connect both shaft with install the coupling bolt and turn simultanously between driven and load shaft.
Good luck
Jabardast please aisi video aur banao
sir pehla dial ka bara tu bathain.ye 90 nova kaya ha.dial ka 100 divisions hain so least count ho ga=1/100=0.01mm yani dial ki 1 div equal ha 0.01mm.or is main ju graduations hain jaisa 0 10 20 30 40 50 60 70 80 90 or phir zero. ye hain 0mm or 10x0.01=0.1mm phir 20 equal ha 0.2 mm or is tarha so on ye 85 ju ap na parha ha ye 8.5mm nahi bhai jan ye 85x0.01=0.85mm ha ok sir. top reading +bottom reading=side reading+side reading is sa hum 3rd reading ju support ki waji sa na par sakhain us ko maloom kar saktha hain.correct me if i am wrong
Sar moja 2 din ki bad alignment Karen hi pump mono aur motor ke to kon kon sy tol chahyi 1 taim karney hi
Jberdast Vedio
Nyc video and such a informative technicque
Thnx meri an dy toty
Everything is ok but you didn't tell yet shim correction method
Please tell to your all subscriber
Sir aapka pas fhitar milega kiya 25salary
Bhai device set keise kiye clear kar diji ye
Aage ka video bheje
Rim-and-Face alignments should be performed with the coupling intact. Running the dial plunger across the opposing coupling surface without rotating that surface with the mounted dial indicator is about as inaccurate as you can get. www.petersontools.com
More dial gauge post
Ok bhai jan and thnx
Axial agar +hai to and radial -hai to ham side kaise milage
Phale axial maximum set karo
Sir paper पर radial and axial alignment की reading lene ke baad kaise alignment karein baatye
muje bhi janana h
Aap ka sawal kya hai reading lene ke bad hi likha jata hai 🤔
Sir axial bhut jyada tirchha h usse koyi dikat to ni h n
What measurements
What he say?
7:28
Is watch ka naam kya hai
Allingn kider Kiya Kuch bhi video
Bhai jan ab videoo man allingn arty to video 5 ganty ki hoti q k bhai jan humy 5 gatny lagy as ko allingn krty huy bhai jan
Nice video brother
ua-cam.com/channels/m8mQZIpspdf_tT6mNVkX_A.html
Biliul hi alignment vedio me kuch nhi amjh aya bakwas
Bakwas Allingment...
Bhaijan aapka number chahiye.