@@terrygermano4555 Terry, I have a dumb question, why is it called a 4"lift if it's using a 3" high block? Sorry, I'm buying an F150 and am learning about these kits. BTW your tuck looks really sharp! Thanks!
@loloforge2841 The rear of these trucks are set higher than the front stock. So it gives the truck a rake. So remember that the rear is about 2 inches higher for towing and bed capacity squat. When you raise the front 4 inches you don't have to go as high in the rear. You want the truck to look level.
@@terrygermano4555 roger that! Thank you. I just saw one of your videos and heard you say that you totaled the white one! OMG. Hope you are ok and sorry to hear that. That white truck was mean looking! What a stance. I assume the grey is identical as it looks like it.
Terry I see that BDS has different versions of 4” lift kits, so which one did you get? I think one of them has the reservoir up front but I’m not sure if you can notice a difference (comfort wise) between that one and the one that doesn’t have the reservoir on the coil over. Thx
Great looking truck! I just got a 23 F-150, will be putting a 4 inch BDS lift with 20x10 -12 offset wrapped in Nitto Ridge Grapplers 33 12.50"s. Just wondering how much trimming will have to be done and wondering if 35's will work without bumper trimming? Any insight to this question?
I have the same truck, im so torn on what i want to do it. I prefer the look of 6" lift. I agree im concerned about getting sick of climbing up there everyday! If you get chance, can you measure from the ground to the bottom of the body right at the driver door? No one ever shows a measurement from there, the Black widow trucks are about 23 in. So I'm just curious what the 4" lift is compared to the 6" Thanks
Thank you Terry, it’s Anthony. UA-cam froze my ability to comment. Haha, So I had to borrow my sister phone! I need to go through your videos. Did you notice a big difference in ride quality?
Of course I could have done 35s. But it all depends on the offset of the wheel on how much that wheel pokes out with negative offset which will determine how much trimming and cutting up of the truck that would need to be done. I'm good with 34x11.5x20 -18 offset. I had very minimal trimming on just the bottom of the valance.
Hello, I have a simple question, will the truck fit into a standard garage door with the 4 inch lift and tires? It looks close but might fit?? Let me know if you could, thank you!
I don't believe it will fit. I know I'm just under 7 feet because that's the touchless car wash limit and a parking garage I was able to fit that was 7feet height limit. My house garage I'd probably hit the door or the garage opener motor on ceiling.
You will be able to put 35s but it will depend on your wheel offset and you will have alot more trimming to do. I'm running 34s 11.5 wide tires. 20x10 -18 offset. Which is a 295/60/20 tire. I bought the kit from the shop that installed it. BDS only uses Authorized Dealers for install for the warranty. The place is Dedona Enterprises in Yonkers, NY. He's been doing lifts on Trucks and Jeeps for 42 years in Business. Not sure where you live?
With this set up you have did u have to cut anything ? I love the 35” look or whatever but I honestly prefer not to cut and then again I think 6inch is jus way to much for me I feel like the 4inch is the enough I jus want the beefiest look if that makes sense like I love your set up !!
35s is pushing with this kit. You might have to cut more than you want. The wheel/tire all goes off what offset wheel you pick. That will determine how much cutting the truck up you will have to do. I wanted 35s too but I also told the shop I didn't want to cut the truck up. So he gave me the best setup with very minimal trimming. I'm on 34s with my setup and it's a big tire bro. The shop I used is in Yonkers, NY. Dedona Enterprises is the shop name. Look him up on Instagram my white 2021 f150 and my current silver 2022 f150 were both done by him and the videos of my trucks are on his Instagram page. He knows his shit. Highly recommend him. Check out his work on Instagram.
@@terrygermano4555 so is this the new thing? Wobble with these new gens lol? Ford has no idea? Super strange . Everyone’s like it’s tires it’s tire. So all these guys have bad tires. I don’t think so. Something with the truck doesn’t like any change at all.
@@DenoTheTruth the 4 inch is the best everyday lift in my opinion. I fit in the cars wash if that helps you. It's does fit in the car parking garages . I've parked in the hospital garage a couple times. I have so much crap in my Home Garage I've never really tried to see if it fits. But I think you should pull the trigger on the 4 inch kit with 3 inch rear blocks!!! I love it!
I got a -19 with 2” lvl kit up front and 1” block in the rear and it doesn’t rub . Tires are nitto ridge grappler in a 275/55/20
Good to know about the 3 inch block. Thanks
Great video...agree with the 4" lift
Thanks!
@@terrygermano4555 Terry, I have a dumb question, why is it called a 4"lift if it's using a 3" high block? Sorry, I'm buying an F150 and am learning about these kits. BTW your tuck looks really sharp! Thanks!
@loloforge2841 The rear of these trucks are set higher than the front stock. So it gives the truck a rake. So remember that the rear is about 2 inches higher for towing and bed capacity squat. When you raise the front 4 inches you don't have to go as high in the rear. You want the truck to look level.
@@terrygermano4555 roger that! Thank you. I just saw one of your videos and heard you say that you totaled the white one! OMG. Hope you are ok and sorry to hear that. That white truck was mean looking!
What a stance. I assume the grey is identical as it looks like it.
Terry
I see that BDS has different versions of 4” lift kits, so which one did you get? I think one of them has the reservoir up front but I’m not sure if you can notice a difference (comfort wise) between that one and the one that doesn’t have the reservoir on the coil over.
Thx
Thanks for the info. Wasn’t sure what size blocks to order for back.
No problem!!! Update me when you get your lift kit installed!!
Sweet ride bro!
Thanks!
love it man!
I have the same truck with 6" BDS and -19 offset, I had to trim the felt as well.
Nice!
With the 6 inch did you have to cut anything with the dif to put the lift on
Great looking truck! I just got a 23 F-150, will be putting a 4 inch BDS lift with 20x10 -12 offset wrapped in Nitto Ridge Grapplers 33 12.50"s. Just wondering how much trimming will have to be done and wondering if 35's will work without bumper trimming? Any insight to this question?
I have the same truck, im so torn on what i want to do it. I prefer the look of 6" lift. I agree im concerned about getting sick of climbing up there everyday!
If you get chance, can you measure from the ground to the bottom of the body right at the driver door?
No one ever shows a measurement from there, the Black widow trucks are about 23 in.
So I'm just curious what the 4" lift is compared to the 6"
Thanks
@@Anthonycapone8146 I will measure it
Thank you Terry, it’s Anthony.
UA-cam froze my ability to comment.
Haha, So I had to borrow my sister phone! I need to go through your videos. Did you notice a big difference in ride quality?
@maryanncaponi364 I just measured from the ground to the bottom of the door...it's 21.5 inches high.
@@Anthonycapone8146 I just measured from the ground to the bottom of the door...it's 21.5 inches high.
@maryanncaponi364 it rides stiffer not boaty like stock. I might upgrade to the coilovers one day.
Are you running any wheel spacers in the back and in the front? And what size spacers are they. Thanks.
@PivitoPivito Negative, No spacers!
Nice truck!
Thank you!!!
you can fit 33x12.50x20 with a 2" level...... shouldve been able to get 35x12.50x20's in this setup.... pretty sure the 6" bds allows 35/37x12.50x20's
Of course I could have done 35s. But it all depends on the offset of the wheel on how much that wheel pokes out with negative offset which will determine how much trimming and cutting up of the truck that would need to be done. I'm good with 34x11.5x20 -18 offset. I had very minimal trimming on just the bottom of the valance.
What rims are those ?! Those are sick
Good video!
What is the overall height of truck?
Hello, I have a simple question, will the truck fit into a standard garage door with the 4 inch lift and tires? It looks close but might fit?? Let me know if you could, thank you!
I don't believe it will fit. I know I'm just under 7 feet because that's the touchless car wash limit and a parking garage I was able to fit that was 7feet height limit. My house garage I'd probably hit the door or the garage opener motor on ceiling.
U should put drop shackles in the rear , stance would look good
Nah I'm not into the squat look! Lol
What’s up bro I jus got my XLT yesterday !! I want to fit 35”s will this kit be enough ⁉️and if so we’re did you purchase the kit?
You will be able to put 35s but it will depend on your wheel offset and you will have alot more trimming to do. I'm running 34s 11.5 wide tires. 20x10 -18 offset. Which is a 295/60/20 tire. I bought the kit from the shop that installed it. BDS only uses Authorized Dealers for install for the warranty. The place is Dedona Enterprises in Yonkers, NY. He's been doing lifts on Trucks and Jeeps for 42 years in Business. Not sure where you live?
With this set up you have did u have to cut anything ? I love the 35” look or whatever but I honestly prefer not to cut and then again I think 6inch is jus way to much for me I feel like the 4inch is the enough I jus want the beefiest look if that makes sense like I love your set up !!
I’m from NJ btw
35s is pushing with this kit. You might have to cut more than you want. The wheel/tire all goes off what offset wheel you pick. That will determine how much cutting the truck up you will have to do. I wanted 35s too but I also told the shop I didn't want to cut the truck up. So he gave me the best setup with very minimal trimming. I'm on 34s with my setup and it's a big tire bro. The shop I used is in Yonkers, NY. Dedona Enterprises is the shop name. Look him up on Instagram my white 2021 f150 and my current silver 2022 f150 were both done by him and the videos of my trucks are on his Instagram page. He knows his shit. Highly recommend him. Check out his work on Instagram.
What size rims are they? 10's wide or 12?
20x10 -18 offset wheels. Tires 295/60/20 11.5 inch wide
I’m curious did you have to cut anything with the dif?
The kit requires cutting the frame to install brackets to lower the diff.
Looking good...
How much rubbing?
Thank you! Just a little on the driver's side front on hard turns on a felt piece in wheel well that I haven't trimmed
Not a big deal.
Nice ride! What are those rims?
Fuel Militia Wheels. 20x10 -18 offset
@@terrygermano4555any rubbing?
@user-ok5go5ut3b very minimal. On hard turns if wheel gets compressed then I get a little rub
@@terrygermano4555 did you do any cutting though?
What was the labor cost to install the lift ?
Cost me around 4k for lift and install
do you have any weird steering wheel wobble at like 90 + km? highway speeds.
Yea I get wobble at 90mph...I'm US so no KM here.
@@terrygermano4555 so is this the new thing? Wobble with these new gens lol? Ford has no idea? Super strange . Everyone’s like it’s tires it’s tire. So all these guys have bad tires. I don’t think so. Something with the truck doesn’t like any change at all.
@TheNet I figured it was because of the lift being higher off the ground with less aerodynamics at high speed.
I have a 4inch rc lift on my 2022 f150 absolutely no wobble at 100mph for me
Do you fit in garages?
Parking garage Yes. Home garage No.
@@terrygermano4555 thank you for answering. I want to lift mine but I’m afraid I won’t fit anywhere. I’ll subscribe 💪🏾.
@@DenoTheTruth the 4 inch is the best everyday lift in my opinion. I fit in the cars wash if that helps you. It's does fit in the car parking garages . I've parked in the hospital garage a couple times. I have so much crap in my Home Garage I've never really tried to see if it fits. But I think you should pull the trigger on the 4 inch kit with 3 inch rear blocks!!! I love it!
What kinda wheels are those?
Fuel Militia
I have same tires and truck with a level and they fit perfect. -18 also But I cut that ugly rubber front air dam off