hi teri if you can help me i'm having some problems.. i've set up my dx7s same as you did here..wired up my mfc-03 using an AR8000 receiver i did the binding process i power it up orange light was flashing and press the bind botton transmitter says binding the orange light went off that's it.. it did not go solid and no confimation if binding was sucess.. i power the mfc and TX their is no light on the RX..
It's the same set up as the video, On the AR6100e put the 4 leads in th following ports... J5 in Aile J4 in Thro J6 in Elev J7 in Rudd Then set dual rate on Elev and Rudd to 75% and 100%... then follow the video to teach the MFC ...
i tried to bind with other two different receivers AR400 and AR6115e both led are not flashing when i power up the mfc-03.. control unit light is solid red and beeps..
Sherwin L when you Bind a receiver you should insert the bind plug and power up the receiver, then press and hold the Bind button and turn on the radio... when Bind is complete power off both TX &RX and then remove the Bind plug, turn on the TX and when it's powered up, turn on the RX.... that should pair them together....
thanks teri it did bind now .. with the TX i made some adjustments for the THRO at first when i move left stick up it goes on reverse and for the ELEV when i move stick up it was engine cold start.. i reverse travel for both and it work.. as for the travel for ELEV and RUDD i change to 150% b'coz the engine wont start even right stick is fully down..
you need to set you radio up exactly as I've shown... the Throttle and Aileron channels are not changed and stay at 100%... you only need to change the Dual Rate on the Elevator and Rudder channels... Expo is not changed on any channel...
Raymond Marsh which Spektrum DX do you have..? I've done "How to" for the DX7S, DX6i and DX6... just follow them and you'll see how it's done... simple...
Raymond Marsh it's pretty much the same as the DX7S.... just set your Dual rate to 75% and 100% on one of the triple rate switches... use position "0" & "1" only.... if i get my hands on a DX8 I'll do a couple more videos...
nice
hi teri if you can help me i'm having some problems.. i've set up my dx7s same as you did here..wired up my mfc-03 using an AR8000 receiver i did the binding process i power it up orange light was flashing and press the bind botton transmitter says binding the orange light went off that's it.. it did not go solid and no confimation if binding was sucess.. i power the mfc and TX their is no light on the RX..
I have a ar6100e with a dx7s i need help setting it up?
It's the same set up as the video,
On the AR6100e put the 4 leads in th following ports...
J5 in Aile
J4 in Thro
J6 in Elev
J7 in Rudd
Then set dual rate on Elev and Rudd to 75% and 100%... then follow the video to teach the MFC ...
@@TeriWilde thank you very much I got it to work i bought it used with no remote..
i tried to bind with other two different receivers AR400 and AR6115e both led are not flashing when i power up the mfc-03.. control unit light is solid red and beeps..
Sherwin L
when you Bind a receiver you should insert the bind plug and power up the receiver, then press and hold the Bind button and turn on the radio... when Bind is complete power off both TX &RX and then remove the Bind plug, turn on the TX and when it's powered up, turn on the RX.... that should pair them together....
thanks teri it did bind now .. with the TX i made some adjustments for the THRO at first when i move left stick up it goes on reverse and for the ELEV when i move stick up it was engine cold start.. i reverse travel for both and it work.. as for the travel for ELEV and RUDD i change to 150% b'coz the engine wont start even right stick is fully down..
do i need to set the D/R-EXPO to 150 when switch to 1 for RUDD and ELEV as well? or do i need to change both POS 1and 2??
you need to set you radio up exactly as I've shown... the Throttle and Aileron channels are not changed and stay at 100%... you only need to change the Dual Rate on the Elevator and Rudder channels... Expo is not changed on any channel...
ok thanks teri..
Can any one tell me how to setup the Spectrum DX with the MFC-03
Raymond Marsh
which Spektrum DX do you have..? I've done "How to" for the DX7S, DX6i and DX6... just follow them and you'll see how it's done... simple...
Sorry its the DX8 I have tried to set it up with DX6 and the DX7 with no luck
Raymond Marsh
it's pretty much the same as the DX7S.... just set your Dual rate to 75% and 100% on one of the triple rate switches... use position "0" & "1" only.... if i get my hands on a DX8 I'll do a couple more videos...
I need help
Awesome