hello, can you please tell me if after turning the flywheel to the letter T, is it important to install the camshaft? I know that the two lines must be parallel to the cylinder head, but the first cam from the timing chain has a specific position, must it be with the tip up or down, or do only the two lines matter? 
hello, I have this model and unfortunately the signals and the stop light do not work on the brake and position, can you help me with this problem, what exactly should I check?
Hi would you be able to make a video about the indicators wiring please? The wiring for the indicators on my Daelim vs have been completely messed up and I have no idea how to sort it. or if you have a wiring diagram that would be very much appreciated. Thank you for posting this video it has helped me so much. Kind regards Sam
@@bikedogtor1663 Hi, Ich habe Ölverlust irgendwo am Ventildeckel. Die Dichtung scheint In Ordnung zu sein. Ich glaube das die beiden Schrauben undicht sind - das war bei Ihnen auch das Problem glaube ich. Wie habe nSie die wieder Dicht bekommen. Gruß CB
Meine daelim stottert seit der Vergaser Reinigung wenn ich mehr als halb Gas gebe . Bekomme keine Leistung. Bei 60 km/h ist Schluss. Vergaser sieht aus wie neu. Zündkerze ist neu und Zündspule auch. Hast du ne Idee was das sein kann.
I ask because I have just cleaned mine ( VS125 2002). I hadnt started the bike since 2010, so there are a few issues. I cleaned the carb and had to clean the petrol tank, using electolysis. The last MOT in the UK ( like the german test but every year for vehicles over 3 years old) said the steering was slightly notchy - but didn't fail on that. Anyway, I am putting it through its MOT in a couple of weeks and just want to say that your videos are very useful. Thanks
well done. good video .. I had entered the engineering site of daelim and I found that the valves adjusted 12.5 all .. I was interested in your 12-16 .. can you tell me a little what performance it has in this setting? I have the machine to repair for a long time now due to lack of spare parts .. I expect the most from daelim korea parts .. my only solution .. and I have some gaps in the camshaft . the central camshaft pin and both rollers have been damaged and I have to go to a machine shop .. so I am close to adjusting the valves .. thanks for pointing me ..
Thank you. I now know that I did the adjustment wrong. Anyway if the valve clearance is a little too big it's not a big problem. At least if the valves don't make a clicking sound, then the clearance is too big. Better adjust it to specs
@@bikedogtor1663thank you for your answer .. you have your chopper as an ornament .. when i finish mine I can take a photo of you .. unfortunately due to the lack of spare parts here i almost lost the summer without the daelim sporadic rides. thanks again doctor .. if I can help and know what information I am here...
grosser Fehler: Ventilspiel bei der VS nach Werkstatthandbuch 0,12mm und nicht 0,1 wie im Video gezeigt... Aber alles in allem gutes Video, hätte man auch in Deutsch machen können...
Danke für die Info. Ich habe zum Ventilspiel verschiedene Infos gefunden und mich für das im Video gezeigte Maß entschieden. Die Hersteller schwanken da selbst manchmal in ihren Handbüchern bei identischen Motoren.
@@bikedogtor1663 ja leider... Mich wunderte es nur, weil Beschreibung ja auf Deutsch ist und dann auf Englisch erklärt wird... ;-) Daumen hoch gab es ja aber trotzdem :-D
![[PROYECTO] ⚡DAELIM VS 125 🚀 Sacando y abriendo el MOTOR🔛](http://i.ytimg.com/vi/aH-043DONGE/mqdefault.jpg)
Some good tips here. Didn't know about the steering head bearing bolt trick, thanks mate.
I want to help people so mission accomplished I would say :-)
You do quality service! It would be interesting to hear the sound of your bike engines in the video
Thank you! I do everything as I would want to have it done.
Well done ! Need help on my bike one goes to the pipe from the reservoir and I don't know where the other hose goes. Thank you
Did you see it in the video?
According to the Daelim Service Manual for VS 125 the correct valve clearance is 0.12-/+ 0.02mm for intake and exhaust.
Great bike, great video! Keep up the good work!
Thanks again, with these nice comments its easier to keep going
hello, can you please tell me if after turning the flywheel to the letter T, is it important to install the camshaft? I know that the two lines must be parallel to the cylinder head, but the first cam from the timing chain has a specific position, must it be with the tip up or down, or do only the two lines matter?

Sorry I do not know. You may find garage manuals for your bike
Wollte einfach mal sagen, tolle und Interessante Videos solche kleine UA-camr wie wir verdienen auch mal Lob.
Danke dir, werde bei dir auch mal reinschauen :-)
@@bikedogtor1663 Mach das. Und dann sag mir was du davon hältst.
hello, I have this model and unfortunately the signals and the stop light do not work on the brake and position, can you help me with this problem, what exactly should I check?
Mabe the bulbs are bad? Or check if the switches work
Thank you for the answear,i solve that proble.Was a wire cable brock
@@bikedogtor1663 how to search for new one this gascket scrwe? 12:23 whats is the name of piece?
Dit moi stp la dimension de la bobine et le pneu arrière
Hi would you be able to make a video about the indicators wiring please? The wiring for the indicators on my Daelim vs have been completely messed up and I have no idea how to sort it. or if you have a wiring diagram that would be very much appreciated. Thank you for posting this video it has helped me so much. Kind regards
Sam
Hi Sam, the bike is sold already so can't do the video you need. But there are some good forums out there with all information you need.
Hallo wie stellt man den Vergaser ein bei dieser daelim meiner geht immer aus?
Das kann ich in einem Kommentar nicht beantworten
Danke...habe gerade so ein altes schätzchen ergattert - jetzt weis ich bescheid :-)
Viel Spaß damit
@@bikedogtor1663 Hi,
Ich habe Ölverlust irgendwo am Ventildeckel. Die Dichtung scheint In Ordnung zu sein. Ich glaube das die beiden Schrauben undicht sind - das war bei Ihnen auch das Problem glaube ich. Wie habe nSie die wieder Dicht bekommen.
Gruß
CB
@@lima621 ich denke da helfen nur neue Dichtungen
@@bikedogtor1663 Flüssige Dichtung hat geholfen. (Y)
Sehr gutes Video !👍
Meine daelim stottert seit der Vergaser Reinigung wenn ich mehr als halb Gas gebe . Bekomme keine Leistung. Bei 60 km/h ist Schluss. Vergaser sieht aus wie neu. Zündkerze ist neu und Zündspule auch. Hast du ne Idee was das sein kann.
Klingt als ob der Schwimmerstand im Vergaser verstellt wurde oder der Sprit Schlauch geknickt ist.
@@bikedogtor1663 wie löse ich das Problem ? Schlauch ist frei Benzin läuft
@@Christian-uo3rc Schwimmerstand kontrollieren
Hola tengo un problema con la mía y es que no carga la batería podrías mostrar como arreglarla gracias desde ya
In english?
Did you have to clean the carburetor ?
No
I ask because I have just cleaned mine ( VS125 2002). I hadnt started the bike since 2010, so there are a few issues. I cleaned the carb and had to clean the petrol tank, using electolysis. The last MOT in the UK ( like the german test but every year for vehicles over 3 years old) said the steering was slightly notchy - but didn't fail on that. Anyway, I am putting it through its MOT in a couple of weeks and just want to say that your videos are very useful. Thanks
well done.
good video .. I had entered the engineering site of daelim and I found that the valves adjusted 12.5 all .. I was interested in your 12-16 .. can you tell me a little what performance it has in this setting? I have the machine to repair for a long time now due to lack of spare parts ..
I expect the most from daelim korea parts .. my only solution .. and I have some gaps in the camshaft
. the central camshaft pin and both rollers have been damaged and I have to go to a machine shop .. so I am close to adjusting the valves .. thanks for pointing me ..
Thank you. I now know that I did the adjustment wrong. Anyway if the valve clearance is a little too big it's not a big problem. At least if the valves don't make a clicking sound, then the clearance is too big. Better adjust it to specs
@@bikedogtor1663thank you for your answer .. you have your chopper as an ornament .. when i finish mine I can take a photo of you .. unfortunately due to the lack of spare parts here i almost lost the summer without the daelim sporadic rides. thanks again doctor .. if I can help and know what information I am here...
Please tell me the number of oil seals and anthers fork motorcycle
Still please wheel bearing size
Sorry I don't know
How many have to be the valve? Sorry i am hungarian
Valve clearance you mean?
@@bikedogtor1663 yes
0,12mm all
@@bikedogtor1663 when the engine is cold or heat?
Szabolcs Bodor only when cold
this is one beautiful motorcycle!
grosser Fehler: Ventilspiel bei der VS nach Werkstatthandbuch 0,12mm und nicht 0,1 wie im Video gezeigt... Aber alles in allem gutes Video, hätte man auch in Deutsch machen können...
Danke für die Info. Ich habe zum Ventilspiel verschiedene Infos gefunden und mich für das im Video gezeigte Maß entschieden. Die Hersteller schwanken da selbst manchmal in ihren Handbüchern bei identischen Motoren.
How to change the spark plugs? Could you do a video? Could I contact you on whatsapp?
You need a spark plug tool to do that. If you have it you just undo them.
@@bikedogtor1663 not really I managed with the tool box I had
Gutes Video...
Schöner wäre nur wenn auch auf Deutsch das erklären würdest für die , die kein Englisch können ;-)
Mußte mir das übersetzten lassen :-D
Dieses Video war nunmal auf englisch :-) freut mich, dass es trotzdem geholfen hat.
@@bikedogtor1663 ja leider... Mich wunderte es nur, weil Beschreibung ja auf Deutsch ist und dann auf Englisch erklärt wird... ;-)
Daumen hoch gab es ja aber trotzdem :-D
Se tschörmans are kamming, ja. Zis is guht ja.
Möchte gern AMMI
:-)