this is great, exactly what I am wanting. I have 2 naked gopros but with one tied up to my umma85, its not much of a "back up." I just finished printing the parts and look forward to putting this together. thank you!
Hi, the fpv cam mount was designed for the cadxx ant, and if i place my runcam nano 2 it touches the frame. That is just my feed back. But nice design, i have micro vibrations on my 95x this will eliminate it.
Try and flip over the TPU dampeners. That will raise the clean plate a few mm.
4 роки тому
Hi! I printed the camera holder and I just found out that there is no hole in the back to plug the power cable on to the Betafpv bec. Can you please make a small hole in the back of the camera mount or for some reason you don't advice using the Betafpv plug? Thanks
Just finished a Mob7 HD w/o HD it was the 8 motor supplied kit with new frame. What is a good pusher prop for upside down mod in 40mm? Waiting for an insta 360 to be stripped down..... :)
Great job and thank you for this. Two questions. Can you provide a solution for the 85x version also. And will you be able to do a build video on a conversion. Thanks again.
You had me at dental floss! I am currently collecting info on how to get that build done, but hesitant on the BetaFPV V.1 BEC board. There are so many different posts on the Naked GP fb group and all are kind of all over the place. Is there a guide on how to solder/connect the BEC board and the GP6 properly. Don't want to short/fry anything. Thanks in advance!
I think a lot of people are doing something wrong or they have some problem with their GoPro main board that has nothing to do with the BEC board. I have two of these and they both work just fine. It should be noted that the connectors (two of them) are difficult to line up. If they are slightly off, and you press down too hard, you can break the connector at the board. I think that is what is going on. The connector breaks and then it gets shorted and frys. If you take your time and line up the connectors properly, it should work assuming nothing else is wrong with your GoPro. I did another one of these conversions after my videos and it didn't work but the GoPro I got was a badly crashed one that wouldn't power on from battery or USB so I was hoping it would work but I was not so lucky. It was dead from the start.
Hey Albert I have a x9 lite s and a XJT module, do I need to update my transmitter through the SD card spot in order to bind and fly my Tinnyhawk 2 and Mobula 6 ? Thanks for all your videos and your help.
Not really. This one uses a swappable camera system and different vibration dampening. What you're saying is "XYZ quad that's inverted is just an Umma95" which is not true at all.
@@AlbertKimTV Quieter than my taycan? Quieter compared to other micro whoops. I know they won't be 'quiet' but sound is more important than speed for what I plan to do.
If you're a beginner, or are like me, and crash often, I wouldn't be buying a Gopro and making a naked one. By the looks of them, one crash, and not that hard of one, and it'll be toast! And you might just F it up just taking it apart! Argh! 😵 Certainly an advanced flying skill level mod, IMO. Oh, unless you have a tree in your back yard that grow $ money $🎄💵💰🌲🙄
Yeah, this kind of project is not suited for beginners. However, I've crashed my Naked GoPro a lot and this case seems to protect it well enough. It's still working. Keep in mind, the overall mass of the drone/battery/camera is well under 200g so even in a crash, the chance for damage is less. Put a naked GoPro on a heavier quad like a 5-inch and it will probably break. However, why would anyone put this on a heavy quad. That would be pointless.
Beta95x for Naked GoPro - bit.ly/2YKkzWX
Beta85x for Naked GoPro - bit.ly/2YJq3B9
My custom build has these parts...
bit.ly/3ihuk6t | bit.ly/2BtRIx0
bit.ly/31xHsyE | bit.ly/3g8wIdY
bit.ly/3cTueyZ
3D printable parts - bit.ly/3gtsgqD
Props - bit.ly/38B5HMC | bit.ly/2wrOcRn
Foam for ducts - amzn.to/3dMxnQN
BetaFPV STL files - bit.ly/2VtktRk
GoPro Lite Case - bit.ly/3cbssYP | bit.ly/2UKXj8R | bit.ly/3hBSR66
BEC Board Only - bit.ly/2MasTIo | bit.ly/3fni7eh | bit.ly/3hGrQi2
Complete GoPro Lite Camera - bit.ly/2M9U1HC
GoPro Hero 6 Black - amzn.to/2XwJXNN
ND Filters - amzn.to/2MoM6Gw
Opening Tools - amzn.to/2X1xu5K
How to build Naked GoPro - ua-cam.com/video/C7z226xuZys/v-deo.html
Footage stabilized with ReelSteadyGo (must have!!!)
Get ReelSteadyGo (w/5% discount) - bit.ly/2V3291L
this is great, exactly what I am wanting. I have 2 naked gopros but with one tied up to my umma85, its not much of a "back up." I just finished printing the parts and look forward to putting this together. thank you!
Great job! it would be cool to have such a modification on beta 85x
Yes please. I have both and will be converting my 95X first. When will be have top prints parts for 85X Albert??? Thanks so much for this. 🙏🏽
Looks like a really nice lightweight cinewhoop !
Thanks!
Would be great to see a build video.
Nice flying and love the music!
Hi, the fpv cam mount was designed for the cadxx ant, and if i place my runcam nano 2 it touches the frame. That is just my feed back. But nice design, i have micro vibrations on my 95x this will eliminate it.
Try and flip over the TPU dampeners. That will raise the clean plate a few mm.
Hi! I printed the camera holder and I just found out that there is no hole in the back to plug the power cable on to the Betafpv bec. Can you please make a small hole in the back of the camera mount or for some reason you don't advice using the Betafpv plug? Thanks
Looks like fun.. Nice little project..
Just finished a Mob7 HD w/o HD it was the 8 motor supplied kit with new frame. What is a good pusher prop for upside down mod in 40mm? Waiting for an insta 360 to be stripped down..... :)
Probably the Gemfan, but I haven't tested a lot in 40mm in the pusher setup.
Would you mind sharing your tune ?
How well does this thing handle with acrobatic maneuvers
These cinewhoops suck at acro IMO. I don't even bother trying anymore.
@@AlbertKimTV my 95 does really well with cinebatic type maneuvers just wondered if this setup can handle a flip or two
Great job and thank you for this. Two questions. Can you provide a solution for the 85x version also. And will you be able to do a build video on a conversion. Thanks again.
No caddx vista in it?
I'll make a different version for that later.
Looking forward to that video as am interested in buying one.
May I know where can I get the duct foam?
amzn.to/3dMxnQN
Great job fighting that wind! Are there any alternatives to RealSteady? I wanted to clean up some runcam footage.
You can use warp stabilizer in Adobe Premiere or the equivalent effect in Davinci Resolve if you want a free video editor.
@@AlbertKimTV thankyou! I have Adobe premiere but i am a total noob. I will check that out!
I wish there is similar mod for beta85x :)
You had me at dental floss!
I am currently collecting info on how to get that build done, but hesitant on the BetaFPV V.1 BEC board. There are so many different posts on the Naked GP fb group and all are kind of all over the place. Is there a guide on how to solder/connect the BEC board and the GP6 properly. Don't want to short/fry anything. Thanks in advance!
I think a lot of people are doing something wrong or they have some problem with their GoPro main board that has nothing to do with the BEC board. I have two of these and they both work just fine. It should be noted that the connectors (two of them) are difficult to line up. If they are slightly off, and you press down too hard, you can break the connector at the board. I think that is what is going on. The connector breaks and then it gets shorted and frys. If you take your time and line up the connectors properly, it should work assuming nothing else is wrong with your GoPro. I did another one of these conversions after my videos and it didn't work but the GoPro I got was a badly crashed one that wouldn't power on from battery or USB so I was hoping it would work but I was not so lucky. It was dead from the start.
@@AlbertKimTV Got it. Alright, fingers crossed, I will give this a try.
what fpv camera are you using 2:30?
bit.ly/3cTueyZ
Hi albert, so the best for this model, using 3s and 4s with 1204 5000kv , than using 1106 4600kv ? Thanks for answering
Do you have a DJI version of the camera mount to hold the full size DJI FPV camera ?
Sorry I don't
Hey Albert I have a x9 lite s and a XJT module, do I need to update my transmitter through the SD card spot in order to bind and fly my Tinnyhawk 2 and Mobula 6 ? Thanks for all your videos and your help.
How do you power the GoPro? Doesn’t the BEC board have a power plug in the back that your mount is blocking?
see this video for details... ua-cam.com/video/C7z226xuZys/v-deo.html
Link to your digital scale, please? Too many choices on Banggood. Thanks!
I got it from Amazon here - amzn.to/2AkOPOA
A close equivalent on BG would be - bit.ly/2ZHsxPZ
want to make something similar but for 85x frame, may you have design for the 85x?
It's in the plans for later but I'm working on something else first. I have many projects going on right now. Can't keep up...
@@AlbertKimTV cool Albert Jeep the projects and new ideas going.
Umma95x amd beta95x is the same thing?
Not really. This one uses a swappable camera system and different vibration dampening. What you're saying is "XYZ quad that's inverted is just an Umma95" which is not true at all.
with its inverted design how do you launch it?
There's bumpers underneath that lift it off the ground a little.
hii albert its running with 3s or 4s ?
I was flying it on 3S
@@AlbertKimTV 450mah or 300mah ?
Albert do u think 1204 5k motors will work or is it only 1105-6? :D
I'm using 1204 motors in this video...
@@AlbertKimTV Looking forward to more about Tiny Cinewhoops 😁
What is the quietest micro cinewhoop you'd recommend? I want to be able to fly close proximity to an individual without a crazy loud buzz. Thanks!
What is a "crazy loud buzz"?... you may find even these smaller cinewhoops are pretty loud too.
@@AlbertKimTV Quieter than my taycan? Quieter compared to other micro whoops. I know they won't be 'quiet' but sound is more important than speed for what I plan to do.
Love it
👍👍
NOICE!!! 👍👍🦈
Dental floss!
If you're a beginner, or are like me, and crash often, I wouldn't be buying a Gopro and making a naked one. By the looks of them, one crash, and not that hard of one, and it'll be toast! And you might just F it up just taking it apart! Argh! 😵
Certainly an advanced flying skill level mod, IMO. Oh, unless you have a tree in your back yard that grow $ money $🎄💵💰🌲🙄
Yeah, this kind of project is not suited for beginners. However, I've crashed my Naked GoPro a lot and this case seems to protect it well enough. It's still working. Keep in mind, the overall mass of the drone/battery/camera is well under 200g so even in a crash, the chance for damage is less. Put a naked GoPro on a heavier quad like a 5-inch and it will probably break. However, why would anyone put this on a heavy quad. That would be pointless.
Exactly what I was thinking. You need $$$ to burn to make this build
👍👍👍