The diameter of column bar is necessary to calculate cutting length....the centre to center distance is necessary for calculation. H= (1000-40-40-8-8-dia.of bar)/5
Its not -8-8 it should be calculated or taken as Centre to Centre stirrups it should be like that 1000-(2*40)-(2*8/2) or 1000-40-40-8/2-8/2 or 1000-80-8 understood as calulated for value a which is 262mm Sir has not calculated the value for H
Sir as biswajith sir (mentioned in comment) sir jab H ki value calculate kartay samay stirups ka dia Jo 8mm hai wo minus nahi kiya hai aapne? Explain. Rest explained was quite good
Ok..bhavesh I give u the reason. Dekho jb maine "a" ki value find kiya to usme maine 8mm minus kiya q k hme dono taraf se 8/2 minus krna tha 4mm and 4mm to hm directly 8mm minus kiye. Isse hme "a" ki stirrups k middle length malum ho gai... Now the main point "H" ki value nikalne k liye hmne 1000-80 kr diye jisse hme stirrups ki length malum hui overall..agr hme overall length chahiye hoti to hm usme se 8mm minus krte but hme to spacing kitni hoti h ye janna tha. To hmne 920 ko devide kiye 5 se jisse hme hr spacing ki middle se length mili h..Q k jb devide krte h to wo middle se count hoti h...bs isliye hme isme 8mm minus krne ki zarurt ni h..I hope apko smjh gya hoga
Ok..biswajit and bhavesh I give u the reason. Dekho jb maine "a" ki value find kiya to usme maine 8mm minus kiya q k hme dono taraf se 8/2 minus krna tha 4mm and 4mm to hm directly 8mm minus kiye. Isse hme "a" ki stirrups k middle length malum ho gai... Now the main point "H" ki value nikalne k liye hmne 1000-80 kr diye jisse hme stirrups ki length malum hui overall..agr hme overall length chahiye hoti to hm usme se 8mm minus krte but hme to spacing kitni hoti h ye janna tha. To hmne 920 ko devide kiye 5 se jisse hme hr spacing ki middle se length mili h..Q k jb devide krte h to wo middle se count hoti h...bs isliye hme isme 8mm minus krne ki zarurt ni h..I hope apko smjh gya hoga
Sir cover deduct karne k bad 1time dia of bar kyu minus karte h,ye to cover k bad add hona chahiye sir,bcoz end to end to steel bhi calculate hoga, pl z reply my query sir
Ye ek procedure hai...jb cover minus kr dete hai to dono taraf se half of dia of bar bhi minus krna padta hai....but practically on site ise nahi bhi kre to koi fark nahi padta....
The diameter of column bar is necessary to calculate cutting length....the centre to center distance is necessary for calculation.
H= (1000-40-40-8-8-dia.of bar)/5
Its not -8-8 it should be calculated or taken as Centre to Centre stirrups it should be like that 1000-(2*40)-(2*8/2) or
1000-40-40-8/2-8/2 or
1000-80-8 understood as calulated for value a which is 262mm
Sir has not calculated the value for H
[1000-40-40-8-8-10( if dia of main bar is 20 mm) -10](span)/ 6 (no.of bars) = 147 mm ( C/C of the main bars distance)
Very Good explanation
Best easily solve to samosa ring thanks
Spacing,,(1000-40-40-8-8-Dia of vertically bars)/5
Sir as biswajith sir (mentioned in comment) sir jab H ki value calculate kartay samay stirups ka dia Jo 8mm hai wo minus nahi kiya hai aapne? Explain. Rest explained was quite good
Ok..bhavesh I give u the reason.
Dekho jb maine "a" ki value find kiya to usme maine 8mm minus kiya q k hme dono taraf se 8/2 minus krna tha 4mm and 4mm to hm directly 8mm minus kiye. Isse hme "a" ki stirrups k middle length malum ho gai... Now the main point
"H" ki value nikalne k liye hmne 1000-80 kr diye jisse hme stirrups ki length malum hui overall..agr hme overall length chahiye hoti to hm usme se 8mm minus krte but hme to spacing kitni hoti h ye janna tha.
To hmne 920 ko devide kiye 5 se jisse hme hr spacing ki middle se length mili h..Q k jb devide krte h to wo middle se count hoti h...bs isliye hme isme 8mm minus krne ki zarurt ni h..I hope apko smjh gya hoga
Very well explained ❤️
Please check the value of H. It will be H=( 1000-80-8)/5=182.4mm ... please reply.
Sir as biswajith sir (mentioned in comment) sir jab H ki value calculate kartay samay stirups ka dia Jo 8mm hai wo minus nahi kiya hai aapne? Explain.
Ok..biswajit and bhavesh I give u the reason.
Dekho jb maine "a" ki value find kiya to usme maine 8mm minus kiya q k hme dono taraf se 8/2 minus krna tha 4mm and 4mm to hm directly 8mm minus kiye. Isse hme "a" ki stirrups k middle length malum ho gai... Now the main point
"H" ki value nikalne k liye hmne 1000-80 kr diye jisse hme stirrups ki length malum hui overall..agr hme overall length chahiye hoti to hm usme se 8mm minus krte but hme to spacing kitni hoti h ye janna tha.
To hmne 920 ko devide kiye 5 se jisse hme hr spacing ki middle se length mili h..Q k jb devide krte h to wo middle se count hoti h...bs isliye hme isme 8mm minus krne ki zarurt ni h..I hope apko smjh gya hoga
Easy and simple
Good 👍
Nice
Sir cover deduct karne k bad 1time dia of bar kyu minus karte h,ye to cover k bad add hona chahiye sir,bcoz end to end to steel bhi calculate hoga, pl z reply my query sir
Ye ek procedure hai...jb cover minus kr dete hai to dono taraf se half of dia of bar bhi minus krna padta hai....but practically on site ise nahi bhi kre to koi fark nahi padta....
@@ENGINEERINGTACTICS thanks for reply against my query
good sir...
Sir aap ki baat samajh me aay lekin square 2 samajh me nahi aaya koi aasan tareqe se samjhaye
Sir hmlog half dia of bar minus nhi krte hai kya ye karna necessary hai jy
Necessary nahi h ..but it is only for accuracy
Apko agar clear cover diya hai to ring bar ka dia minus karne ki jarurat nahi hoti quoki koi bhi contractor agree nahi krta
App kisi video main site per bhi calculate karnay ka method batatay hain aur kisi main nahi
8legged sitrrups in column cutting length calculated video
Ok..
your calculation approgematly right but not correct, stirrup out to out lenght
Dear i couldn't understand the value of H.HOW WE DIVIDED BY 5.
PLS CLARRIFY.
There is 5 spacing between bars
Not satisfied
Sir 4 times bend up ho rha 135 par aur aap sirf ek hi bend up le rahe ho
How to calculate at site
Keep note book. Calculator. Pen... and calculate in cool mind ..
CL-.928m
+EngineeringTactics aapbe 135 internal angle kyu dikhaya? Internal angle to 45 hoga na ??
Internal angle 45° hi hai
135° hook ke liye bend kiya h uska h
Sar nhi samajh me aya
Galat bataye apne apne H ki value nikalne ke liya kiwal cover minus kiya or half of stirrup or half of longitudinal bar minus ni kiya
6 bar thi na longitudinal bar to 5 hi consider kiya hai ha calculation galat hai thoda
Mujhe calculator se simple easy bataye please
First of all to find spacing = 1000-[2 x clear cover )-(2xdia of stirrups)-(2×1/2 main bar dia)÷5 = X
Call me asif bhai, my nane AZhar
Bro Tu jitna english bol raha sariya ka kaam karne wala worker itna english sayad hi samajh paay ga