Realistically, our LEDs don't normally fail. If issues arise with "dead" LEDs, it stems from a weak solder joint and causes a disconnect from the PCB to the LED bank. We offer a standard warranty but 9 times out of 10, these lights last longer than the owners keep the bike.
Good install video. My question is since the programming buttons are on the back; how do i program after I install it? It appears to me i don’t hv access to the buttons afterwards ...
It would help if you didn't skim through thte video and actually watched the instructional material in its entirety. Timestamp 5:30 shows and describes the connections, then they are shown and described again in a few other places. Please use the material that we have provided in its entirety.
@@TSTindustries I see a wade of cables you just say "we have a few other cables here them are for the license plate light and turn signals" like what cables are for the turn signals and which are for the license plate light? Like point out what cables are what they all look the same for me
@@GlorySnipes two of the connectors are identical, those are for the turn signals. There is a third connector that is the opposite of the two for the turn signals, that is for the OEM license plate light.
First of all that taillight and fender eliminator combo looks super clean 👌🏼 Now, do you guys ship overseas, to Portugal to be more specific? Considering getting the taillight, the fender eliminator and the front blinkers
We do ship to Europe. You can place the order right on our website and we will ship straight to your door. Just know that we are off a few days for Christmas. We will be back December 26th.
I presume the 2021 model has a similar or the same tail end? Just wondering since yamaha did quite a little design change starting in 21. This light would look great with it
Yes, it's the same exact light and fender eliminator set-up for the 2021 model but the turn signal connectors are different. If you navigate to our site you will see a 2021 specific category.
@@TSTindustries Oh, different year. I have a 2017 and it doesn't have those. I installed my tail light this weekend.. Looks and works perfect. The sequential blinkers are a nice touch.
@@elboukhaarilaoumadi7151 that is very interesting because the description of this video has the link to the product page. Anyhow, this is where you will find all the products we make and/or provide for second gen MT07 tstindustries.com/yamaha-fz-07-mt-07-2018/
You can try to check out through our website with your address to see if that location is served. It comes down to shipping availability. We have certain locations blocked because shipping there is either a nightmare of packages always get lost. Best thing to do is to try and see if our system allows the location.
What if my new tail light doesn't have fasteners? It's just the wires. My tail light matches up perfectly but my signal wire has two prongs my new light only has one prong. Do I splice the wire into the old wire and use the old fasteners?
@@bobbystewart500 email our Support Team with some photos and we may be able to help. Obviously working with another companies product isn’t something we normally do but we can fix their mistakes by helping you out.
Is this good for Europe mt 07 2020 ? Thinking about ordering this for Portugal, but mindful of the extra charges because of vat of a non Eu country order... is your shipping to domicile with no extra cost ? Thank you
The shipping costs are dictated by the shipping company. We do not charge extra to ship to a home vs. a business. I would say that you should check your connectors on the OE equipment on your bike and compare them to the ones we show in the photos and video here. If they match then this will be compatible with your bike.
Yes. We sell a special splitter that plugs into the Yamaha bike harness and provides two connectors for signals on each side. The splitter can be found on our MT-07 category page here: tstindustries.com/Yamaha-FZ-07-MT-07-2018/ under the title "TST Yamaha Y-Style Signal Harness Splitter"
@@TSTindustries unfortunately not legal, in Germany you need a minimum distance to the indicators because you could otherwise confuse them. what about the hazard lights? is it still recognizable?
The 2018+ tail light is different than the previous gen model. You can probably mount the newer one to the frame of the older bike, but the fairings will not build around it the same way.
Not this one. We have a different light for the 2015-2017 model of the bike. You can see it here tstindustries.com/TST-LED-Integrated-Taillight-2015-R3-FZ07.html
Help. I just installed this onto my 2019 MT-07. Powers up and turn signals fine. However, I can't get it to change programming. I press the button while it's powered on but nothing. Am I doing it wrong?
A trick we use is to leave one of your signals activated and with each press of the button, press down on your brake lever. if it still is not changing after that, shoot our support team an email with a short video and we will work to get you all taken care of.
@@TSTindustries So I did install the relay (tstindustries.com/tst-led-flasher-relay-gen2.html). I noticed that the lights don't light up when I press on the brakes. It just stays red but the turn signals work (except for changing the programming)
Please contact our customer service guys through our site. They will be able to troubleshoot with you and get you going. UA-cam is not really where we do troubleshooting cases, but it sounds to me like you have the brake light tripped permanently by one of your brake switches.
@@gurudarshan5824 Well, since the MT-15 is not available in our market we aren't able to make a tail light for it. In effect we don't have a taillight to show in the video.
You guys are gods with your tutorials. Keep it up!
Ordered the smoked tail light along with the elite one bracket. Couple months ago 07 looks like sleek and clean. Thanks for these tutorials 👍
You're very welcome.
Hello. Is the product suitable for the 22 model and do I need balancing resistors or flasher relay?
Yes for fitment, no for resistors or relay - they're not needed.
@@TSTindustries Thank you
How long does the LED last? I just installed and was curious when I’ll have to undergo this again?
Realistically, our LEDs don't normally fail. If issues arise with "dead" LEDs, it stems from a weak solder joint and causes a disconnect from the PCB to the LED bank. We offer a standard warranty but 9 times out of 10, these lights last longer than the owners keep the bike.
Good install video. My question is since the programming buttons are on the back; how do i program after I install it? It appears to me i don’t hv access to the buttons afterwards ...
The button is still accessible after installation. You may possibly need the help of a small tool.
@@TSTindustries Had i watched the whole video properly; i’d hv answered my own question. Nevertheless, thanks for the prompt reply.
Is there any instruction video how to install the load resistors to fix hyper flashing?
We haven't done a video on that but every resistor kit comes with pictorial printed instructions
What should I do if I don’t have them 4 rubbers from previous light ?
Maybe it would help if you showed us what wires your plugin in
It would help if you didn't skim through thte video and actually watched the instructional material in its entirety. Timestamp 5:30 shows and describes the connections, then they are shown and described again in a few other places. Please use the material that we have provided in its entirety.
@@TSTindustries I see a wade of cables you just say "we have a few other cables here them are for the license plate light and turn signals" like what cables are for the turn signals and which are for the license plate light? Like point out what cables are what they all look the same for me
@@GlorySnipes two of the connectors are identical, those are for the turn signals. There is a third connector that is the opposite of the two for the turn signals, that is for the OEM license plate light.
@@TSTindustries how come my brake light dont work for the rear brake only for the front brake lever
@@GlorySnipes your brake pedal switch is most likely out of adjustment or disconnected.
I've got mine installed. Super easy. How do I program different flashes?
There is a button on the enclosure of the tail light. It is accessible from the trunk compartment. Each press toggles you through nine program states
First of all that taillight and fender eliminator combo looks super clean 👌🏼
Now, do you guys ship overseas, to Portugal to be more specific? Considering getting the taillight, the fender eliminator and the front blinkers
We do ship to Europe. You can place the order right on our website and we will ship straight to your door. Just know that we are off a few days for Christmas. We will be back December 26th.
Boas, sempre mandaste vir? correu tudo bem? e estas satisfeito com o produto? Também estou interessado e queria saber a tua opinião
I presume the 2021 model has a similar or the same tail end? Just wondering since yamaha did quite a little design change starting in 21. This light would look great with it
Yes, it's the same exact light and fender eliminator set-up for the 2021 model but the turn signal connectors are different. If you navigate to our site you will see a 2021 specific category.
@@TSTindustries thank you very much
Is this eu homologated? If not, can it be homologated at RAR (Romanian Automotive Register)?
Not at this time.
@TSTindustries that's sad but thank you.
What are those red fairing pieces on the back by the passenger seat?
The OEM tail fairings?
@@TSTindustries Oh, different year. I have a 2017 and it doesn't have those. I installed my tail light this weekend.. Looks and works perfect. The sequential blinkers are a nice touch.
@@bman3800bman3800 Thanks for the love and support!
Where can i get that license plate holder?
Same place as the tail light, TSTindustries.com
please before i buy this i need a question answered... Is this tail light just as bright as stock? ty!
I think tpu can draw upon the reviews of this product on our website
Hello, I'm looking for the video of the different flash pattern options. Anybody have a link? Would be greatly appreciated. Thanks.
Hello, do you still have this product in your website ?
Of course...it's one of our hottest sellers
@@TSTindustries I have a MT 07 model 2018, I couldn't find it for my bike
@@elboukhaarilaoumadi7151 that is very interesting because the description of this video has the link to the product page. Anyhow, this is where you will find all the products we make and/or provide for second gen MT07 tstindustries.com/yamaha-fz-07-mt-07-2018/
Hi ! Great tutorial! Do you guys ship to Reunion Island? It's next to Mauritius (Indian Ocean) The tail light looks awesome!
Also, I already have LED turn lights on my number plate holder, can I only connect the break light cable? (and not the turn lights cable)
You can try to check out through our website with your address to see if that location is served. It comes down to shipping availability. We have certain locations blocked because shipping there is either a nightmare of packages always get lost. Best thing to do is to try and see if our system allows the location.
You can absolutely use the tail light without using the signal function.
@@TSTindustries okay thanks a lot guys! Keep up the good work
Is necessary the fender eliminator kit for install ?
No, not at all.
What if my new tail light doesn't have fasteners? It's just the wires. My tail light matches up perfectly but my signal wire has two prongs my new light only has one prong. Do I splice the wire into the old wire and use the old fasteners?
@@bobbystewart500 email our Support Team with some photos and we may be able to help. Obviously working with another companies product isn’t something we normally do but we can fix their mistakes by helping you out.
Will it strobe when I hit the breaks
If you program it to do so by pressing the programmable button on the back, yes.
Is this good for Europe mt 07 2020 ?
Thinking about ordering this for Portugal, but mindful of the extra charges because of vat of a non Eu country order...
is your shipping to domicile with no extra cost ?
Thank you
The shipping costs are dictated by the shipping company. We do not charge extra to ship to a home vs. a business. I would say that you should check your connectors on the OE equipment on your bike and compare them to the ones we show in the photos and video here. If they match then this will be compatible with your bike.
Conseguiste comprar este farol em Portugal?
do you need load balancing on 22 model?
Not at all. The 2021+ model utilizes an internal light control module to regulate the turn signal flash rate as the OEM lights are LED by default.
Can we run the turn signals and this together?
Yes. We sell a special splitter that plugs into the Yamaha bike harness and provides two connectors for signals on each side. The splitter can be found on our MT-07 category page here: tstindustries.com/Yamaha-FZ-07-MT-07-2018/ under the title "TST Yamaha Y-Style Signal Harness Splitter"
Please advise Yamaha MT15😍🙏
What are you asking? We don't have the MT15 in the USA so we're a little confused.
bikes looks so sexy after eliminating the fender 👍👊
We agree!
Is the 2021 the same
As far as fit for tail light and our fender eliminator the 2021 is the same.
Legal in germany?
You would have to check your local laws prior to placing an order.
@@TSTindustries unfortunately not legal, in Germany you need a minimum distance to the indicators because you could otherwise confuse them. what about the hazard lights? is it still recognizable?
Can i take the rear lighter of mt07 2018 on the 2016?
The 2018+ tail light is different than the previous gen model. You can probably mount the newer one to the frame of the older bike, but the fairings will not build around it the same way.
am I missing a cable? my tail light came with 3 male end wires but I noticed I have a female end missing? is this normal?
The fourth connector you're seeing on your bike is for the license plate light.
@@TSTindustries yes, after some further digging I got it sorted out and it works perfectly. Love the product too!
Will this work for the 17 fz07??
Not this one. We have a different light for the 2015-2017 model of the bike. You can see it here tstindustries.com/TST-LED-Integrated-Taillight-2015-R3-FZ07.html
Can I put this on my MT-03 2019 ?
No, you need the other light we make for the r3 and mt03
ua-cam.com/video/6HBQC4rFZDI/v-deo.html
@@TSTindustries thanks
Does this fit a 2020 mt-07?
Yep!
Why won’t my push fasteners go back in correctly? They’re loose and don’t fasten when I push them in.
on the 7 there are a few sizes of these push fasteners. Make sure that you are using the correct one for the location you are trying to fasten.
Help. I just installed this onto my 2019 MT-07. Powers up and turn signals fine. However, I can't get it to change programming. I press the button while it's powered on but nothing. Am I doing it wrong?
A trick we use is to leave one of your signals activated and with each press of the button, press down on your brake lever. if it still is not changing after that, shoot our support team an email with a short video and we will work to get you all taken care of.
Nvm. Forgot about load balancing resistors that was in the package. I need to install those
@@808djsho or skip that painful step and purchase our relay. 😉
@@TSTindustries So I did install the relay (tstindustries.com/tst-led-flasher-relay-gen2.html). I noticed that the lights don't light up when I press on the brakes. It just stays red but the turn signals work (except for changing the programming)
Please contact our customer service guys through our site. They will be able to troubleshoot with you and get you going. UA-cam is not really where we do troubleshooting cases, but it sounds to me like you have the brake light tripped permanently by one of your brake switches.
If you are ok with the quick flashing on the turn signals, is it ok to not have a relay installed? This is not damaging in any way correct?
That is correct.
Make MT-15 vedio
We do not have an MT-15 in our market.
@@TSTindustries if you get make a vedio plzz we are waiting for that
@@gurudarshan5824 Well, since the MT-15 is not available in our market we aren't able to make a tail light for it. In effect we don't have a taillight to show in the video.
Will this fit Aus spec bikes ? I don't know if they change plugs around or anything.
Will this work for the 19 fz7 (mt07) ?
Yup. I've got it on my MT-07 2019 :)
@@nicolairamsby11 thx :)