I have same washer. Floor got flooded about 3 inches deep. Washer turns originally but won't turn in reverse unless I give it a push. I was thinking I should clean all the contacts and squeeze some graphite on the moving parts and check the wire harness with a little volt meter to see if anything burnt out. What would you suggest?
Thank you very much. Because of your video, I put the belt back on and fixed the screw that fell out! My Zeny is working! I really appreciate your help.
Well after a little over 2 yrs mine finally went out the motor was fine and I didn't know where to start.. I'm so happy I found this video ...Thanks for sharing .
Thank you for this video where you changed the belt on the twin tub washer. I had mine in the tub, left for awhile and the tub flooded so the washer was sitting a about a foot of water. The spin side works but the washer side doesn't and you can hear the timer ticking. I will let it dry out for a while and if it doesn't start working I will check the belt. Thank you for all the information.
Can the 3 screws your removed with the socket be replaced? If so what kind of screws are they and would a place like Lowe's or Home Depot have em? I just got my Zeny and noticed that one of the washers from the bottom fell
I've repaired this washer before. You didn't reset the pulley on the motor. You have to untighten the set screw on the motor pulley and theN push down on the pulley until you can see motor shaft sticking out and then tighten set screw.
I have a costway and it looks exactly the same in there . I have only had mined for 45 days an it just stopped working (the wash side) so I'm going to buying a belt. But I wanna no it still makes noise just doesn't spin when turned on do u think its the belt?
My washer fell and now both spinners won't work how can I get the washer and the spinner to work again.the belt is still brand new not sure if it just completely broken or I really do need a new belt how can I tell?
I have a tacklife & everything works completely fine however at the top of my machine next to the wash knob when the washer shifts it’s like a blue light kinda like a spark & that’s scared tf outta me so I stopped it what causes that to happen & should I be concerned bc I can’t find any information on that
My problem is that I have to keep the button pressed for it to spin. How do you think I can solve the problem with the centrifugation?. It spins perfectly as long as you hold the button.
Would you know about the Timer for the wash side?? Mine worked..till it didn’t. Grrr it won’t Time nor will it reverse the agitation. I can Lightlyyyy turn to almost 3 and it agitates or rather Twist the light load into knots. Thanks
My washer washes fine but the spinner works sometimes and sometimes it does not. When it does not it agitates super aggressively shaking the machine but when it's working properly it doesn't shake the machine I can actually hear it just spinning....do you think I need a new belt?
I have the zokop had to change the drain hose on it because it cracked and was leaking... And the old hose drained really slow as the original hose was by the manufacturer bent in like 4 spots inside the machine.. To replace it was a real b--- because they not only clamped it to the drain pump but glued it on as well!! And i had to squeeze my one had in that tiny little access port to do it.. You think the manufacturer would be a little more repair froendly especially with the drain hose since it is thin cheap plastic.. you think they would know it would probably need replacement.. I put a proper heavy grade washer hose on it.. I had to drill a new exit hole at the bottom of the machine because the hose couldn't be bent up the way the other was.. But... i got it. and... The machine works perfectly now.. No problems with the belt though... At least net yet anyway.. And i use it a lot.. And with the new drain hose it drains like a normal washer now.. With the old hose it kept stopping as it drained and only a trickle of water came out as it drained.. (And no it wasn't the pump.. it was becase the hose was bent in like 4 spots to turn it in all directions inside the machine..) The washer is great though.. I actually absolutely love it.. It cleans the clothes incredibly well.. And since the hose replacement, it works beautifully now..
Hi any help would be appreciated my spinner has a weird noise coming out by the inside by the hose I can hear it to loud so I just stopp the spinner and I’m tempted to open it up and look inside it sounds like something broke off please help me with any information thank you.
So I have one like youres and both area stop working the number in my belt is 0-560E and I don’t find that one in Amazon can I still use the one you got . Help 😢
Hey man did this end up fixing it? Mine spins but doesn't spin fast enough. I don't know anything about this stuff. So any help or advice would be appreciated!
I have a question, my mom has one, works great, one problem is, the ringer part, where you out the clothes innto ring out the water its not turning, could you help?
OMG, it only takes 5 minutes to change. Open the back, lift the belt up and over the pulley. Take new belt and go back between pulley and motor and position it, and fit one side on pulley and feed it back on when turning. I am 64 years old and did it in 5 minutes with just a screwdriver to remove the back panel for access to the pulley
Please help!! My portable washing machine's spin tub spins really slow and it makes a burnt rubber smell. How do I fix this and what's causing this smell???
I've had one issue that turned into mess of issues, oops many hands in the cookie jar.. my bolts and rubber washers holding the motor need replaced now, mine did not come loose, do you have any suggestions or what can replace in a bind, any info deeply appreciated
Hi I'm hoping someone sees this and can help. I had the same problem but the bottom of the machine has broken off. Like when he gets to the very last step. The white piece to the screws he's tightening have broken so I can't tighten it and I think that's the problem. Now the whole motor is lose, how can I fix that?
I was sooo excited to fix my non-spinning Kuppet spinner side after watching this at 2am. I ran to the bathroom this morning with my tool kit and I couldn't believe there was clothing stuck between the wall and the inner drum. After getting it out with a clothes hanger, I crossed my fingers and turned it on... crickets. 😭😭😭 I removed the back plate and checked the belt. It's fine. When I turn in the washing side, the belt moved perfectly. I can't find any reason for the spinner to not be spinning. 😭😭😭 I can't afford a new one, so I will keep searching for a solution.
I got a zokpod washer from my cousin the dryer part is spinning as it should but when I use the washer part I turn the knob to wash u can hear the timer working and I looked at the belt it looks ok so I'm guessing it needs motor replaced wonder how hard or expensive it be do replace the motor but it don't spin or washer part at all can someone confirm my suspicions ?
Does the motor make any noise at all? It should at least hum. If there is no noise except for the ticking noise, it is likely an electrical issue such as a contact getting loose. If it hums but the pully does not spin, it's likely the motor run capacitor going bad or the motor itself starting to fail.
I work at a warehouse with the most kick ass boss and I knew If I took this to him he would figure it out and he did. Something so minute caused the motor to go out in the spin cycle side. Apparently there is a little stop/start lever pully behind the knob that controls it and if you attempt to stop the cycle before time or naturally if it came from the manufacturer tightened too tight it will start to wear out the teeth on the motors wheels because essentially that’s what keeps them turning together and the teeth is what stops the cycle. If those are worn down you fry the motor and all it can do at that point is make a noise like the lil engine that could but go nowhere. So it would cost almost $100 to replace the part🤔 I paid $88 total for this on eBay from manufacturer anewday. They refunded me rather than replacing. I was still gonna try to fix but my manager ended up getting his wife’s Walmart account and used her points to get me a brand new one🙏🤲🏾 he looks like the real life Santa Claus and mrs claus could be his wife but he is real life an angel walking amongst us and he should be posting a video on how to repair using a scrap yard motor off of a lawn mower or something similar to show you it can be done as he is now fully invested in this project😂 so just keep searching or I will update soon
Hello thank you for this. I changed the belt and did everything watching your video. When i turn it on it makes a loud noise and i cant see what it could be. I need help 😫 it is the same noise it was making before changing the belt. I tought it was the belt but i gues it wasnt. The old belt was in good condition too.
I wouldnt know what it could be without looking it. You need to make a video so I can see what it doing, If you fix the problem feel free to share with us. A warranty is good thing to have when buying this machine,
Hi mine had a very loud noise coming out by the motor and the hose I watched another video that wash showing how he opened the back of the machine took down the hose and there I found a dime in there and thank god my machine is working fine try to open yours and see what’s in there ok . Good luck
You can buy a universal extension hose. If you take that little hanger off the end of the existing hose then you can tape or use a clamp to affix the hose extension to that hose. This will only work if you are running the hose along the ground level, it will not work if you have to run the hose into a higher drain.
MY Castaway washer stop working. The motor is after few noises completely silent. Motor is "XD 90 wash" do you know were you can buy it. Alibaba can sell them for you but minimum 100 pcs. Any other place you mite provide.
@@brendadavisscrapitydoda1284 good luck Brenda. My washer still does not work. I allow my clothes to soak in detergent for 30minutes, rinse and spin dry. It does the trick!
Thank you! I have a similar machine that was gifted (broken) to me. I first had to fix the connection from the spinner to underneath, the little rubber piece that attaches to the bearing/shaft had come loose, once that was fixed I noticed it was losing traction quite easily (worn/loose belt) I had actually loosened the bolts you show in the video but it wasnt coming loose. Before I was going to take the whole thing apart I figured I'd look into it, found this video, and knowing that it does in fact loosen, I loosened the bolts more until I could tighten the belt by moving the whole assembly, did so and now it works perfectly! Do you have the part number for the belt, Im sure I'll need a new one at some point. Thanks again! Liked and subscribed
Hi, I'm having issues with the water from the washer side collecting into the spinning tub even though its below the cut off portion. Would you happen to know how to fix this issue? Thanks!
I had that issue twice turned out to be socks stuck in drain, first time sock made it to drain hose, second time they fell through opening between spinner and housing and were stuck in drain opening
I take socks out with a stick that i bought its called hair snake is used to unclog toilets or sinks but i use it for this because it happens a lot and i has helped me a lot.
@@josephineedmonds4906 There are several videos on fixing that. But many need a new motor and i want to figure out where to get a new motor for the spin side.
I'm not sure what that would be with out looking at, have you looked in the inside?, you need to make a video of outside and inside so i can see what it is doing, make sure clothes not stuck in there. somewhere.
Just opened it and hooked it up I didn’t want water over the floor and put the whole thing in the tub and the bottom got wet I guess and that’s why it probably won’t work just got it and messed it up please help
@@quonnkoger1504 were you able to get it working? i got a zeny portable last week and neither sides function, the motor's running but seemingly not connected to either wheel. i took off the back, checked the hose, which is was shipper suggested.
Another possibility. When you turn the knob to drain mode, it pulls on a cable inside the machine that then lifts up a spring loaded valve to let the water out. The cable may have come loose.
Im not sure what that could be without looking at it , sounds like the motor, a switch, or something stuck around spinner, open the back and look very closely at things, if you buy another one , make sure you get to warranty plan.
![REPAIR SPIN TUB NOT FUNCTIONING! [Eureka EWM-750D ELITE ]](http://i.ytimg.com/vi/UI8-J96gMJg/mqdefault.jpg)
![REPAIR SPIN TUB NOT FUNCTIONING! [Eureka EWM-750D ELITE ]](/img/tr.png)
As a single mother I just want to say thank you🙏🏽
hope everything go well for you thks
I have same washer. Floor got flooded about 3 inches deep. Washer turns originally but won't turn in reverse unless I give it a push. I was thinking I should clean all the contacts and squeeze some graphite on the moving parts and check the wire harness with a little volt meter to see if anything burnt out. What would you suggest?
That sounds like a good start ,by letting things dry out. Water on electric parts really mess things up, I'm not to sure about that one.
I feel ya! :)
Came here to say the same!
Thank You....I got one of these washers,and your the only one that I see thats teaching how to fix things..
Thank you very much. Because of your video, I put the belt back on and fixed the screw that fell out! My Zeny is working! I really appreciate your help.
Hi my spinner is making some weird metal noise by the hose area any suggestions on what can I do?
I have the Costway...I can't imagine it being that much different. Thanks, this is good info to have.
Well after a little over 2 yrs mine finally went out the motor was fine and I didn't know where to start.. I'm so happy I found this video ...Thanks for sharing .
Thank you for this video where you changed the belt on the twin tub washer. I had mine in the tub, left for awhile and the tub flooded so the washer was sitting a about a foot of water. The spin side works but the washer side doesn't and you can hear the timer ticking. I will let it dry out for a while and if it doesn't start working I will check the belt. Thank you for all the information.
exact thing happened to me. did you have to replace the belt or did drying it out work?
Same here! Any updates
My washer side works but the spin side does not work
Bruh you saved my life man!! Turns out the bolts were just loose and it was out of position.
Thx a lot for this video!
Good job, thank you. Tomorrow I'll take a look at my friends Panda washer that looks like the same machine.
Good job and all done with one hand !
Thanks dude, this was helpful
Thanks for video. Own a small washer like this, about 1 year now. My problem is with the rinse drum. Its unbalanced and shaving the inside out!
Dang just today my washer was not spinning uughh I jus got my portable 3 months now thanks I understand what I need to do now yey
Thanks this was really helpful
Any advice for not having a bad belt, but the washer side making a loud scraping noise type thing consistently with both directions of the spin?
Thanx ordering new belt and sending my kids the $180 labor bill
Can the 3 screws your removed with the socket be replaced? If so what kind of screws are they and would a place like Lowe's or Home Depot have em? I just got my Zeny and noticed that one of the washers from the bottom fell
I've repaired this washer before. You didn't reset the pulley on the motor. You have to untighten the set screw on the motor pulley and theN push down on the pulley until you can see motor shaft sticking out and then tighten set screw.
Is there any possibility that you could send me a wiring diagram?
Hello, I want to know how I can do that? How I can reset the pulley on the motor? Thanks
Why does he need to reset the pully if he never removed the pully in the first place?
@@charleneconner6845 why would you need a wiring diagram? Are the electronic controls not functioning properly?
Thanks for the video
Thank you kindly
I have a costway and it looks exactly the same in there . I have only had mined for 45 days an it just stopped working (the wash side) so I'm going to buying a belt. But I wanna no it still makes noise just doesn't spin when turned on do u think its the belt?
My washer fell and now both spinners won't work how can I get the washer and the spinner to work again.the belt is still brand new not sure if it just completely broken or I really do need a new belt how can I tell?
I have a tacklife & everything works completely fine however at the top of my machine next to the wash knob when the washer shifts it’s like a blue light kinda like a spark & that’s scared tf outta me so I stopped it what causes that to happen & should I be concerned bc I can’t find any information on that
hi i need to get the drying basket out because there are clothes that got stuck down there is there an easy way to do it
My problem is that I have to keep the button pressed for it to spin. How do you think I can solve the problem with the centrifugation?. It spins perfectly as long as you hold the button.
Would you know about the Timer for the wash side?? Mine worked..till it didn’t. Grrr it won’t Time nor will it reverse the agitation. I can Lightlyyyy turn to almost 3 and it agitates or rather Twist the light load into knots. Thanks
My dryer stopped spinning. Would this also be a belt issue? Or is the belt replacement specifically for the washer component?
Thank you 💕
I appreciate your time, Thanks a bunch,
My washer washes fine but the spinner works sometimes and sometimes it does not. When it does not it agitates super aggressively shaking the machine but when it's working properly it doesn't shake the machine I can actually hear it just spinning....do you think I need a new belt?
My washer won't spin do I need to replace the belt?
Is this belt generic for most mini washers? Mine is the zokop model.
I have the zokop had to change the drain hose on it because it cracked and was leaking...
And the old hose drained really slow as the original hose was by the manufacturer bent in like 4 spots inside the machine..
To replace it was a real b--- because they not only clamped it to the drain pump but glued it on as well!!
And i had to squeeze my one had in that tiny little access port to do it..
You think the manufacturer would be a little more repair froendly especially with the drain hose since it is thin cheap plastic.. you think they would know it would probably need replacement..
I put a proper heavy grade washer hose on it..
I had to drill a new exit hole at the bottom of the machine because the hose couldn't be bent up the way the other was..
But... i got it.
and...
The machine works perfectly now..
No problems with the belt though...
At least net yet anyway..
And i use it a lot..
And with the new drain hose it drains like a normal washer now..
With the old hose it kept stopping as it drained and only a trickle of water came out as it drained..
(And no it wasn't the pump.. it was becase the hose was bent in like 4 spots to turn it in all directions inside the machine..)
The washer is great though..
I actually absolutely love it..
It cleans the clothes incredibly well..
And since the hose replacement, it works beautifully now..
Hi any help would be appreciated my spinner has a weird noise coming out by the inside by the hose I can hear it to loud so I just stopp the spinner and I’m tempted to open it up and look inside it sounds like something broke off please help me with any information thank you.
Tool Man Tim busts out the electric drill for sum 1/4 screws RAAAAAR 🤣 Got it done tho 👍
Are you able to do a video showing how to take the dryer drum out?
I haven't made a video of that yet, If I do, I will definitely post it.
Thank you
Thks , Glad this could help.
So I have one like youres and both area stop working the number in my belt is 0-560E and I don’t find that one in Amazon can I still use the one you got . Help 😢
Where did you buy new belt ?
Where did you get the belt
Hey man did this end up fixing it? Mine spins but doesn't spin fast enough. I don't know anything about this stuff. So any help or advice would be appreciated!
Mine doesn’t spin enough and made a lot of noise coming out from the water pump by the hose maybe buying another water pump may help ? In my case .
I put too much wet clothes in the drying spinner, it hits the sides and makes loud banging noise when it spins now. Is there a way to fix this?
I have a question, my mom has one, works great, one problem is, the ringer part, where you out the clothes innto ring out the water its not turning, could you help?
if I have a problem with the ringer, I will do a video on it. I haven't had that problem yet .
OMG, it only takes 5 minutes to change. Open the back, lift the belt up and over the pulley. Take new belt and go back between pulley and motor and position it, and fit one side on pulley and feed it back on when turning. I am 64 years old and did it in 5 minutes with just a screwdriver to remove the back panel for access to the pulley
how do I fix the spin Timer
Do u know how to unclog the drain pipe?
Please help!! My portable washing machine's spin tub spins really slow and it makes a burnt rubber smell. How do I fix this and what's causing this smell???
I've had one issue that turned into mess of issues, oops many hands in the cookie jar.. my bolts and rubber washers holding the motor need replaced now, mine did not come loose, do you have any suggestions or what can replace in a bind, any info deeply appreciated
I'm not sure what happen . Lowes may have some tools to help you out. Hope you get your washer fixed.
What if you got the motor wet will it work once it dries out
If there is no rust damage, it will be fine
Can u link the belt?
Hi, anyone knows how to fix if the washer keeps draining even if it’s set to wash?
Hi I'm hoping someone sees this and can help. I had the same problem but the bottom of the machine has broken off. Like when he gets to the very last step. The white piece to the screws he's tightening have broken so I can't tighten it and I think that's the problem. Now the whole motor is lose, how can I fix that?
Does the motor spin freely with the belt off?? My motor starts to spin but then stops
Omg same !
What about when the spin cycle isn’t working but it washes clothes perfectly? Do we need to replace the motor?
This is my issue too. Did you happen to find an answer to this? The dryer just stopped spinning for me randomly and only 3 months old
I don’t have that brand it’s just the washer but mine’s will start to wash then stop suddenly 😢help
I was sooo excited to fix my non-spinning Kuppet spinner side after watching this at 2am. I ran to the bathroom this morning with my tool kit and I couldn't believe there was clothing stuck between the wall and the inner drum.
After getting it out with a clothes hanger, I crossed my fingers and turned it on... crickets.
😭😭😭
I removed the back plate and checked the belt. It's fine. When I turn in the washing side, the belt moved perfectly.
I can't find any reason for the spinner to not be spinning.
😭😭😭
I can't afford a new one, so I will keep searching for a solution.
I really hope you get it fixed . If you find the problem and get it fixed please share with us, Thks
My washer won't spin either, what do we do?
Did anyone find a solution?
Did you get to fix your kuppet mine has a weird metal noise coming out of it.
@@soniaolaguez3399 I never did. 😕
My ? Is mines not washing, could it be the belt?
My dryer part will not work any videos on that part?!?!
I got a zokpod washer from my cousin the dryer part is spinning as it should but when I use the washer part I turn the knob to wash u can hear the timer working and I looked at the belt it looks ok so I'm guessing it needs motor replaced wonder how hard or expensive it be do replace the motor but it don't spin or washer part at all can someone confirm my suspicions ?
The pulley on motor needs to be reset. Untighten setscrew, push down on pulley until you can see the motor shaft, and tighten up set screw
@@jeremydavis2703 how do I do that?
I'm in the same boat too
Does the motor make any noise at all? It should at least hum. If there is no noise except for the ticking noise, it is likely an electrical issue such as a contact getting loose. If it hums but the pully does not spin, it's likely the motor run capacitor going bad or the motor itself starting to fail.
Hello, can you do a video or post instructions in the comments on what to do if the spinner side stops spinning?
I work at a warehouse with the most kick ass boss and I knew If I took this to him he would figure it out and he did. Something so minute caused the motor to go out in the spin cycle side. Apparently there is a little stop/start lever pully behind the knob that controls it and if you attempt to stop the cycle before time or naturally if it came from the manufacturer tightened too tight it will start to wear out the teeth on the motors wheels because essentially that’s what keeps them turning together and the teeth is what stops the cycle. If those are worn down you fry the motor and all it can do at that point is make a noise like the lil engine that could but go nowhere. So it would cost almost $100 to replace the part🤔 I paid $88 total for this on eBay from manufacturer anewday. They refunded me rather than replacing. I was still gonna try to fix but my manager ended up getting his wife’s Walmart account and used her points to get me a brand new one🙏🤲🏾 he looks like the real life Santa Claus and mrs claus could be his wife but he is real life an angel walking amongst us and he should be posting a video on how to repair using a scrap yard motor off of a lawn mower or something similar to show you it can be done as he is now fully invested in this project😂 so just keep searching or I will update soon
If your on amazon , Put in O-600E belt , it will say Brand : X-Dr ( X-DREE O-600E 600mm Inner.... Thks.
Thank you so much
make an affiliate link from it and place it in the description :) you can earn extra money that way,lots of people are looking for this belt
I can’t find the belt on Amazon 😔
Hello thank you for this. I changed the belt and did everything watching your video. When i turn it on it makes a loud noise and i cant see what it could be. I need help 😫 it is the same noise it was making before changing the belt. I tought it was the belt but i gues it wasnt. The old belt was in good condition too.
I wouldnt know what it could be without looking it. You need to make a video so I can see what it doing, If you fix the problem feel free to share with us. A warranty is good thing to have when buying this machine,
@@fhfd-dy3tj i understand. I did the warranty thing i will look into it. I was trying to fix it before doing that, but ill just do that. Thank you 🙏
Hi mine had a very loud noise coming out by the motor and the hose I watched another video that wash showing how he opened the back of the machine took down the hose and there I found a dime in there and thank god my machine is working fine try to open yours and see what’s in there ok . Good luck
@@soniaolaguez3399 Thank you for that 🙏
How do you put it on the bottom pully
Its a little hard to do, you got to take your time , hold and swing around motor pulley . it take little maneuver.
Have you had to extend the drain hose? If so do you have a video
You can buy a universal extension hose. If you take that little hanger off the end of the existing hose then you can tape or use a clamp to affix the hose extension to that hose. This will only work if you are running the hose along the ground level, it will not work if you have to run the hose into a higher drain.
Spin basket won't spin. You can hear the motor come on won't spin. It will turn manually.
What is it don’t drain with pump panda XPB52A
MY Castaway washer stop working. The motor is after few noises completely silent. Motor is "XD 90 wash"
do you know were you can buy it. Alibaba can sell them for you but minimum 100 pcs. Any other place you mite provide.
I never used Alibaba.com , But look like they have it. Has anyone used Alibaba.com. Leave in comments if you ever used Alibaba.com .
Great Video! I would like to kindly ask if you can provide the link to where you bought it at from Amazon so I can know I am buying the right one
Yes plz
Oh thank you so much! I have a Costway portable washer and the washer does not spin.
I haven't worked on the Costway washer. If I do , I will make a video on it . Thks
Ok thanks!
My washer won't spin either
@@brendadavisscrapitydoda1284 good luck Brenda. My washer still does not work. I allow my clothes to soak in detergent for 30minutes, rinse and spin dry. It does the trick!
How to clean this kind of machine if it's clog up
Thank you! I have a similar machine that was gifted (broken) to me. I first had to fix the connection from the spinner to underneath, the little rubber piece that attaches to the bearing/shaft had come loose, once that was fixed I noticed it was losing traction quite easily (worn/loose belt) I had actually loosened the bolts you show in the video but it wasnt coming loose. Before I was going to take the whole thing apart I figured I'd look into it, found this video, and knowing that it does in fact loosen, I loosened the bolts more until I could tighten the belt by moving the whole assembly, did so and now it works perfectly! Do you have the part number for the belt, Im sure I'll need a new one at some point. Thanks again! Liked and subscribed
Just take it off before it breaks and get one that is a very little bit smaller
My belt is fine what else can be wrong you can hear it but it doesn't move
The spin side of my machine is working but not draining out how would I fix that
I have a different video on this channel that may help.
Wish I can hire someone to fix mines that's too much bending for my bad back
I replaced the belt, but the tub is still NOT turning. What else could it be?
Im not sure without looking at it, sounds like something loose or not working. if you get it fixed feel free to share with us.
Hi, I'm having issues with the water from the washer side collecting into the spinning tub even though its below the cut off portion. Would you happen to know how to fix this issue? Thanks!
I had that issue twice turned out to be socks stuck in drain, first time sock made it to drain hose, second time they fell through opening between spinner and housing and were stuck in drain opening
How did you get the sock out? Having the same issue
I take socks out with a stick that i bought its called hair snake is used to unclog toilets or sinks but i use it for this because it happens a lot and i has helped me a lot.
is this for washing part or spinner? my spinner doesnt spin
My spinner doesn't work too. Did u find another video how to repair ? Thanks
@@josephineedmonds4906 There are several videos on fixing that. But many need a new motor and i want to figure out where to get a new motor for the spin side.
Just got mine today from home depot and my spinner doesn't work either. Don't know if i should try to fix it or return it.
@@groovylicks6 I returned mine.
Bro my washer spinning and dryer stop working but it only make noise
The belt for mine is not the same unfortunately. Mine requires A-710E
ok ,hope you get it going perfect.
Mine won’t agitate or spin? Any help ?
I'm not sure what that would be with out looking at, have you looked in the inside?, you need to make a video of outside and inside so i can see what it is doing, make sure clothes not stuck in there. somewhere.
Just opened it and hooked it up I didn’t want water over the floor and put the whole thing in the tub and the bottom got wet I guess and that’s why it probably won’t work just got it and messed it up please help
@@quonnkoger1504 were you able to get it working? i got a zeny portable last week and neither sides function, the motor's running but seemingly not connected to either wheel. i took off the back, checked the hose, which is was shipper suggested.
I have the same washer but my belt is a 0-560e
Mine doesn't drain
Just figured out Oxyclean was what made the belt start slipping.
How?
@@HollyATme The powder may have gotten under the spinner and damaged the water seal, causing soapy water to leak onto the pully.
Where i can find vbelt O 535 E belt
I think E-Bay will be your best bet on that belt.
mines doesn’t drain any idea of what it could be 😭?
You could have something stuck on outside of spinner. I have another video on my page that may help you out.
Another possibility. When you turn the knob to drain mode, it pulls on a cable inside the machine that then lifts up a spring loaded valve to let the water out. The cable may have come loose.
But i don't see nothing wrong with the belt?
My spinner is tight and won’t spin
Im not sure what that could be without looking at it , sounds like the motor, a switch, or something stuck around spinner, open the back and look very closely at things, if you buy another one , make sure you get to warranty plan.
I🤣😁