How to replace front hub bearing assembly on 2007 Acura MDX
Вставка
- Опубліковано 23 сер 2024
- Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic
Repeat, you do not have to remove the ABS sensor, don't waste your time. 36 mm socket for axle nut 2007-2012 MDX. Be prepared, one hub may come off with 30 seconds of effort, the other side three hours. Ask me how I know. Had to use PB blaster, bolts and BFH.
and when the problem hub came off, it came off in chunks! But it did come off....
Well that gives me the warm and fuzzies for my next Saturday
It took you 3 hour's now you have me scarrd to do my shit😶
Do you need to touch the sensor at all? How does the sensor fit into the knuckle? I was thinking using a bearing puller, small one, to get it out.
Excellent video! You did say why replaced wheel bearing, noise or normal maintenance
Noise
I'm gonna do mines next weekend on the 13 or 14 of November..wish me luck I have to do the front I pray I can beat them out I have all the tools
Yeah that’s the hard part but few bangs should get it out. Anyways good luck!! Let me know how it went
@@RBTheMechanic I will Sir
Great video !! Thank you. I need to do this.
32 I believe I do sho in video I think so
Great Video!
Thank you.
No problem!!
Is this the same for 2015 acura rdx? Thanks!
Yes diffrent parts numbers and might be bit diffrent set up but over all same
Where is your shop bro , I will bring my truck there.
I’m located north nj Bayonne ru local?
Would these assemblies work on a Honda Ridgeline??
Yup
How did you remove de sensor ? Did you save it or took it out in parts? Or you don't have to remove the sensor to install the new hub.
wgalicia1978 u don’t have to remove the sensor
thanks
Welcome
How did you get it in bro.
It was giving me hard time to get the axle in I just brushed up the axle shaft and then it went it it’s like very perfect match I though it was wrong bearing but eventully went it
Thanks
Hey would the sane work for a 2005
Same diffrent part number
Is the soon coming from the mix? I’ve never heard it from mine ;)
Huh?
When your lifting up on the abs sensor, spray the WD40 UNDER THE GAP WHILE THE SENSOR IS BEING PULLED UP LET THE SIT FOR A LITTLW AND TRYING LIFFING UP AGAIN THE WD40 WITH THE STRAW.
Usually these r siezed in honda and Acura the bore is too tight they should had redesigned
@@RBTheMechanic I was just watching and seen when you tryed taken the abs sensor out with the needle noise.
The sensor lifted up but was like sulking back in the room you had when you lifted up the sensor.
I would have liked to use the WD-40 with the straw and spray around maybe some 40 will fall down and around helping get out the sensor.
Plus when the hub bearing came out starting some on the inside because it seem to have pressure holding it in place.
That pressure could of been release after the bearing was remove.
Next video throught me what I need to know about how to change my brakes and change my hub bearing all by my self with the right tools.
@@Thoumillixwinty not sure about the pressure thing but these are always stuck
How can i know that they're already damaged?
marcosbarrera66 you will hear a humming sound and the faster u go the louder it will get if u hear it very low little and barely can tell wait till it get louder also check tire thread if ur tire thread is out of shape it will also make false sound as if it’s ur bearing
@@RBTheMechanic is this the same steps for a 2005 Acura TL?
@@jeffringer236 no Acura TL has compressed bearing
@@jeffringer236 it’s somthing similar to this ua-cam.com/video/SA2FVov-HQE/v-deo.html
@@RBTheMechanic Got dammit Acura
Is a 04 the same?
I believe 2004 is compressor bearing
@@RBTheMechanic okay thank you
he didn’t show how to how he didn’t most of the work.
Did have few other videos to help as much as I can
@@RBTheMechanicThanks can I do this with a regular impact drill or does it need to be an air one?
@@SomeWhereByMarzzz yes u can use anything that can impact it usully hammer dose the job this was but too much jammed
Man u seem skipping all the important part!
Which pat hammering?
Axle nut its not 32!! Its 36mm!
Sorry dude but this is a hackjob -
netgun777 hckjob?
Nice job man!
How long does this job normally take?
How much is labor?