great tutorial, thanks! I'm always afraid to get my fingers near the chuck, I like your method of putting the inside glue ring on slowly instead of at speed like a lot of other people.
Habe mir beide deiner Videos angeschaut und gesehen das du auch Deutsch sprichst. 😁 Sehr toll gemacht 👍🏻 Habe auch mal ein Abo da gelassen und würde mich über weitere Ring Videos freuen 😉.
Good Question! I always had issues with that. I tried to put Tape between, but than the Ring got Stuck to the Tape 😅 Than i just put it on carefully. Maybe you can try to put some oil or wax on the dowel, but i never tried this Method 😂 Thanks for your comment 👋🏻
Hi! Beautiful work! Just curious if you ever have any issues with the CA finish cracking or lifting from the wood or if you have any suggestions on how to prevent this?
Hi 👋🏻 Thank you 😁 On some rings the finish was seperated from the Wood after a short time. On Others the Finish looks perfekt even after years. Its important to work really careful to get any dust or air between the coats. Also dont Sand the Ring too smooth so that the glue has a good grip. And maybe it depends on the Wood itself.
Depends on thickness of the layers. I don't spend much time on the Low and rough grits to not remove the glue. On the higher grits i sand between 30-60 sec. Hope this was helpful 😅 Thx for your comment 👋🏻
great tutorial, thanks! I'm always afraid to get my fingers near the chuck, I like your method of putting the inside glue ring on slowly instead of at speed like a lot of other people.
Thanks for your comment 😁
Yes, safety is very important 👍🏻
Very cool! 👍 Some days ago I made rings from Eucalyptus. 😃
Habe mir beide deiner Videos angeschaut und gesehen das du auch Deutsch sprichst. 😁
Sehr toll gemacht 👍🏻
Habe auch mal ein Abo da gelassen und würde mich über weitere Ring Videos freuen 😉.
Super, danke dir. Für's Lob und für's Abo. 😃
What prevents the ring from getting stuck to the dowel/mandrel when you apply the ca glue?
Good Question!
I always had issues with that.
I tried to put Tape between, but than the Ring got Stuck to the Tape 😅
Than i just put it on carefully.
Maybe you can try to put some oil or wax on the dowel, but i never tried this Method 😂
Thanks for your comment 👋🏻
Hi! Beautiful work! Just curious if you ever have any issues with the CA finish cracking or lifting from the wood or if you have any suggestions on how to prevent this?
Hi 👋🏻
Thank you 😁
On some rings the finish was seperated from the Wood after a short time.
On Others the Finish looks perfekt even after years.
Its important to work really careful to get any dust or air between the coats.
Also dont Sand the Ring too smooth so that the glue has a good grip.
And maybe it depends on the Wood itself.
What thickness CA do you use? Which plastic polish wascused?
Hi 👋🏽
In this Video ist used Medium ca glue and a plastic polished that i found on Amazon.
Thx for your comment👋🏽
Question where did you get the sand paper pads? Different grits?
I bought them on Amazon. They are called micro-mesh Pads. The Grits go from 1200 to 20000.
Thanks for your comment 😉
U know if Akfix 705 will work too ?
Hi 👋🏻
I never used this glue
Its important to use high quality ca
Thanks for your comment 😁
What's the average time for every sanding level?
Depends on thickness of the layers.
I don't spend much time on the Low and rough grits to not remove the glue. On the higher grits i sand between 30-60 sec.
Hope this was helpful 😅
Thx for your comment 👋🏻