Godspeed Coilovers Installation/Adjustment Guide 2023 | Camber | Height | Preload | Divorced Setup
Вставка
- Опубліковано 20 лип 2024
- In this 8 minute video, Jimmy@E-Autosports.com attempts to explain how to adjust and install your newly purchased Godspeed Project coilovers. This video covers camber plate adjustment, height adjustment, damper adjustment, setting up spring preload and ride height on a divorced rear coilover setup.
Coilover PDF guide:
godspeedproject.com/media/Ins...
Shop Godspeed Coilovers On Our Website:
e-autosports.com/collections/...
Instagram:
/ eautosports
Facebook:
/ eautoinc
0:00 Talk
0:51 Damper Adjustment
1:13 Camber Plate
2:02 What's Preload
3:01 Preload Adjustment
4:00 Ride Height Adjustment
6:18 Divorced Coilover Setup - Авто та транспорт
Bro thank you so much for this video. Just put a set of mono ss on my mini cm and this video has helped me so much while I dial in my ride height!!
Nice vid. My '12 Mazdaspeed springs are nowhere near that length (19cm). So I went to the Godspeed site and watched their somple preload vid. All good... Only thing I'd say is be careful tightening the bottom ring down extra hard (use a brass drift if you do, not a chisel). Either the PO or a shop cranked one of mine down way too tight. Thought I might have to heat it, but penetrant and smacking it with a drift broke it free - but at the cost of one of the bosses on the lower ring. Be smart.... Thank you for the vid - especially the part at the end about not returning them lol hilarious
Dude that lifted Miata is sick
Amazing info earned a sub from me 👍🏼👍🏼
Just bought some s13 godspeeds for my q45. Hopefully they fit better than cut BC coils
Can you adjust it straight into the car? And avec putting on news coils is it true that you should go do an alignment? I just bought a little accent and I was looking at these Godspeed for my accent 2012🤷🏼♂️
I have Godspeed coilovers, am I able to change the springs on them with swift springs?
I just got my Godspeed coilovers for my 2023 Hyundai Sonata N line and really like build on these. Thanks for this video as it will help as Im installing these my self!
How they holding up?
@@TahoeOG_ wonderful
The biggest thing that helps is how wide my tires are and sticky they are it keeps the rubbing almost gone and lets me go DEEP in corners!@@TahoeOG_
I need help I just purchased an installed Godspeed coil over mono ss
On my RSX type S 06 and the plate does not line up side to side only at an angle when I have side to side, the bolts do not line up through the holes
Has anybody else had this problem?
Where can I find info about what preload should be?
I have mono ss for prius 2010 and can't find info about preload.
hey man how can i go lower when they’re already maxed out? or am i just outta luck lol
I just installed some monoRS on my e92. Confused on adjusting the fronts you say to lower the car use the upper big ring and to go higher the big ring but aren’t those two locked to each other all you gotta do spin clockwise or counter for Lower or higher? They are both lock so spinning the big shouldn’t mess the spring load because the bottom it’s already loose and free to spin the shock body.
Any full video on Divorced system? Should both bottom
I just bought a 2011 rav4 Toyota and it has these. The ride is too stiff for me and when I go over a speed bump or pot hole it seems the car is going to fall apart. Not sure if they lowered this car before I bought it also. $hit seems to complicated for me. I just want a normal stock ride. I’m in Stockton Ca. Can you suggest the closest place to me to have this adjusted if possible?
So while on the car my bottom locking ring never tightens down.... It just keeps going and never gets tight.
I am having a problem out of my godspeeds I've had them about 2 years and ever since I got them the have had almost like death wobble and the steering wheel shakes back and forth. Have had them swapped out once problem was fixed for a short time, then came back and advise on what to do would be much appreciated
I have a 2010 Prius. How much lower can I get it from stock? I was thinking on just getting lowering springs but they say it only drops about an inch to an inch and a half. Could I lower it 2-3 inches? In your experience, how much is the comfort affected at 2-3 inch lower ride height?
Can I adjust my dampener while installed and car is on ground (not on lift or jack)???
Is there a compatible version for 2010 Toyota Blades?
Why does the coilovers body move around when it’s installed, isn’t it supposed to be still?
I have Godspeed coils on my 2019 civic sport and I understand it will be stiffer but I can be going 3 mph and hit a rock with my back wheels and catch air. Also what is a safe height for raising the coilovers. I feel I’ve maxed mine out and have no idea how much thread is left but my car is still soo low to the ground
Have same issue with my dirtbike lol
Soften the dampening?
Soften them
What causes the coil overs to be slamming?
Preload not set maybe
Right I have the Mono RS on my Q70L, and the front hits hard . Had it raised up some and it settled right back to the ground again
@@teaminfiniti4105how much did you lower it? I'm looking to grt a set of these for my q70 as well
Gearing up to put a set of these on my 04 Elantra GT
Do you have an Instagram for you car? I just bought a set for my 11 elantra touring
you are the best bro no other video could give me what this one did thank you 🫶🫶🫶