4 stage super boiler for my man " Los"
Вставка
- Опубліковано 4 жов 2024
- This video contains Paid links that gives me a 6% commission if you click and buy any product on that website . Mono tube boiler build how much does it cost ??? $,$$$
Check out my web site www.nobox7.com/
Check out my store front www.amazon.com...
Support this channel on Patreon www.patreon.co... - Наука та технологія
sand or rough up the outer surface with sand paper make it a matte finish it wont reflect as much heat probably make it easier to weld also but your welds look pretty good for what you are using to weld them.
Good idea
Can confirm that stainless rejects IR heat quite nicely. I see the general recommendation was bead blasting. There are commercial bluing solutions for stainless though not sure if they'd hold up to the environment or if they'd undermind the chrome layer that's so crucial to why stainless is, well stainless.
Apply a lid over the coils that reflect the heat back down on purpose! Re: A polished piece of stainless dome lid
there pal!
As far as heat distribution, between the coils have you considered taking another stainless steel tube capping off one end pour in some rubbing alcohol preheated and cap off the other end. Use these tubes as a heat distributor.
I am not a physicist by any means but from what we did at work over the years with stainless steel tubing for heat absorption, the print most of the time stated to bead blast the surface for a matt finish. This supposedly made all the difference with that metal type and what the engineer would state and specify. Way cheaper than using any plating for heat resistance. The paint idea I would be leary for sure. The paints today are better than yesteryear but the coating is not that robust for longevity. That is my ten cents fella. Peace
makes sense, all the peaks and valleys from bead blasting increase the surface area and decrease reflectivity. every little bit counts with stainless as it is a rather poor heat transfer material. shame it has other desirable properties that make it the preferred choice.
@@lanceyeakel7674 Years ago steel started to become out of favor because of the RUST aspect of the metal. Copper brass aluminum started to see a shiny horizon. That when chromium steel popped out of the woodworks. Then stainless steel ant the rest is history. Good day Lance. VF
add some vinegar to your tap water. it dissolves calcium buildup, some restaurants use it for their steamers .
You can burn the surface of the coil with bare acetylene flame (no oxygen) it will get nice and black carbon ''paint'' that never burns out.
you have to build this type of pump
@@NOBOX7 and what kind of pump is that?
Do a light bead blasting on the tubing, then apply heat paint or send the tubing out for dark anodizing finish work???
Greatest boiler
Thanks friend
Nafurahi kuona marejesho ya maoni yako na mm najaribu kutengeneza steam boiler lakini bado haijakubali vizuri halafu mm niko zanzibar nitafurahi kupata elimu hii kutoka kwako asante
A "Steam Ginny" type boiler would seem a whole lot easier and cheaper to get up that runs off off diesel or kerosene!
Sure, a propane fired super heater that is temperature controlled, such as for a car wash or whatever and is precise
is a good proposition but is not necessarily cost effective! I can however see other applications such as use of this
system in commercial laundry service, hospital settings, aviation perhaps and perhaps steam heating plants such
as in old buildings, once it is scaled up to meet a special purpose boiler systems. Yet the portability as such of this
system doesn't seem too bad! The boiler super coil is quite bodacious and the overall efficiency of your heating method
should be great, but I must say the propane fuel usage just might be still a bit high. Just looking at your primary layout
to concept is pretty damned keen! And so, I must continue to watch on into the completion! You are seeking to make
for a great professional build and your client should be receiving every bit of that! Super video and thanks for showing
us folks!!
What would it take to make a less powerful flash boiler? Like say max 200psi for model steam engine usage?
Can't wait to see it in action!
I know right , I pulled all the stops on this design , twice the coill size as the test boiler even switched from co flow to counter flow at the last second , knowing the power of the latter , risky ? yes but arent all good things risky ? This is not prius , this is a beast....
and the smoke? it's hot, you could do like the old boilers and add another stage, instead of the middle part have an coil, could be an cylinder with water and tubes with the exhaust of the liquid smoke, heating even more the boiler
با عرض سلام وخسته نباشید ازاینکه این ویدو را بطور کامل ارسال فرمودید بینهایت از شما تشکر میکنم امیدوارم همیشه موفق باشید خدا نگهدارتان
Could you use the "wall of water" to preheat the boiler feed water?
I ¹would love to built a flash tube boilerfor my 1/4hp coke bottle engine.
I've got a fifty foot coil of 5/8" copper tubing, but that's it.
Could you use just wire instead of welding?
Cold weld..?
How about a parts list!
What grade of stainless steel are you using? Some grades are affected badly by heating and cooling?
316
Exellent. Do you think the steam bike will pull?
конечно потянет
только перевод кривой
What is this for?
Anybody know how to make a water level cut off for a flash boiler that doesn't require any electronics? I would like some kind of solid state device that will cut off the pump automatically without being sensitive to moisture, corrosion, etc.
float switch in a site tube on side of boiler
@@NOBOX7 Good idea. I had a video that showed a process using microelectronics and I knew tht was not a robust long term solution. I am working on a gasifier, but a small turbine or steam engine might last longer than a tiny engine. It is loud and inconvenient to charge batteries with an engine of even a few horsepower. I think smaller is better except for running larger tools and equipment.
can you make one to me .. i want to consume 20 liter per mintue i will use it to extract salt from salt water
Can this set up handle 500-1200psi? And maintain 180 degrees?
yes
Nafurahia kuona hii
Shukrani kwa rafiki yako ya maoni, unafurahi uliipenda, sikuwa na hakika ikiwa ilikuwa yenye thamani ya kutuma
How does someone get ahold of you?
Nobox7@yahoo.com
Let me no if you got that last message , youtube has bin throttling my comments
@@NOBOX7 yeah I got it bro. I'll email you in a bit
boiler generator
Only, Use Stainless Steel Swagelok fitting. They are the Best, At 1000 degrees and At 2000 psi these fitting will hold these pressures. There is NO Substitute for for these Fitting.