Mini Lathe - drilling without drill
Вставка
- Опубліковано 23 сер 2024
- A few weeks ago I got some used micro boring bars. With them it's possible to make holes without drilling before. In this video I make a mount for the micro boring bars and test it.
I've used mini bars like these for years at my work, but never thought to try one without drilling a hole first. Well done, Sir!
Thank you!
The tool looks like a typical mini boring bar from ph HORN. I admire the willingness to make your own frames, although they are available in several sizes. From an economic point of view, making a hole in this way is a big waste of time, especially when you need to make a deeper hole, in a harder material and in addition in a series of, for example, 1000 parts, but the idea itself is very positive in terms of a DIY enthusiast.
Love the video--no music or hoopla--very relaxing.
I bought a similar second hand set from Bengs. I think the brand is Paul Horn. A new set is very expensive! They work wonderfully, but I got serious chatter on tin bronze which is rather hard and brittle. These tools are normally used with internal cooling in CNC machines, behind a screen. Be careful not to crash them. Flying carbide fragments can penetrate the body. They need some sharpening on a diamond wheel after a while. Maybe I will build a simple tool grinder.
Thank you very much for the good tips! I have a Diamond wheel for a dremel engraver which i use for the sharpening of tungsten electrodes. I will try this if it becomes necessary.
AqqqaqaqQQqaaq
Qq
@@randomtechnician KÄRCHER defekt
@@wilfriedhautel2131 No,works fine 😅
I love this format of video no bullhit just straight up good machining work and its kinda like an ASMR for dudes that love shop work like myself lol great video!
Thank you very much!
Je kan inderdaad in veel gevallen met een Boorbaar een gat maken zonder voor te boren.
met een 12 mm Iscar boorbaar met wisselplaatjes gaat het ook..
Je hebt deze boorbaartjes gekregen schreef je, er bestaan er ook met gewoon een Cilindrische schacht, dus volstaat in dat geval een gaatje boren en daarna ruimen voor een goede passing, en dat zal een stuk stabieler zijn dan dit gat, de achterkant van deze boorbaartjes heeft een schuine kant, die kun je gewoon af laten steunen op een klein Paspennetje dat je dwars door je houder perst, en dan heb je meteen een diepteaanslag
Als je een slijpmachine met Diamantschijf hebt, kun je ze ook zonder al te veel moeite zelf slijpen uit versleten of gebroken freesjes van VolHardmetaal, werkt perfect, ik maak zelf ook zo mijn boorbaartjes, en gebruik ze in Titanium
Buf!! la precisión brilla por su ausencia!!, la herramienta te canta como una campana a pesar de ponerle una chapa, teniendo comparador, has metido el latón a las bravas, además no veo el motivo de castigar a la herramienta sin un taladro previo, en mi taller no te contrataba con esas referencias, aunque yo me dedico a la industria del molde y es muy exigente
Como dicen en mi Pueblo: "mucho circo para una maroma"
Mình rất thích khi được xem bạn chế biến món đồ trên các máy công nghiệp. Chúc bạn luôn được bình an, nhiều sức khỏe và tràn đầy niềm vui trong công việc nhé 💞👍
Horn bores you can have coolant running through them used many of these very good for a finish turn brings out a good finish if used properly
Yes, i know ;)
I use these tiny boring tools on my micro lathes, they're excellent! I prefer the Sandvik and Iscar branded ones because they have an ordinary round shank which makes things much easier. 👍
Thank you for the tip, i will look at that
I'm not sure if it's a problem or advantage to have round shank boring bars?
Sometimes you want to change top angle so you can rotate them in holder but other times they can be a pain to get 'dead level'
@@1crazypj Some of them have a flat spot on them to make leveling easy. 🙂
Good to know … what is the name of these tools for the search fonction please ? 😊
@@olivvapor4873 Iscar picco 👍
Another great video! You do good work.
Thank you!
I did this on accident a couple of years ago on a citizen swiss lathe. The drill broke on a copper job and the ph horn boring bar kept making holes. I couldnt believe it.
Profestional friend.
Yoy did very well. Great job.
Thank you very much!
I can't help it but wounder if boring via the tailstock gives better precision. At least on a mini-lathe where cross-slide is so unstable, or........
Very fun! That is the cutest little multifix-style toolpost. What size is it, AA?
Thank you, yes it's AA
Es bueno, asta para hacer fresado y roscas
12:40 I have he same set of drills and taps, bought mine at Lidl 😀
I dont't even know where i got this. 😅
Subscribed! Wonderful video, thank you
Thank you very much!
Nice video
Половина видео про изготовление квадратного проката из пластины :)
Nice video, thank you for sharing it :)
Thank you!
Neat tool holder but are the mini indexed boring bars cheaper than a drill of same size?
I like what you made and could possibly have a use for it but I think I'll stick with conventional drill bits and boring bars
No, the advantage is that you can make very precise holes with any (small) diameter, but i also would suggest to drill before, so the boring bar works much smoother
@@randomtechnician I use these type of carbide bars when making bush bearings for model engines. You can get them right down to 3mm diameter which makes it easy to bore precise bronze main bush bearings dead on size.
Avete visto che per fresare il parallelepipedo stretto in morsa , vengono usate quelle che vengono chiamate "parallele" ? ( devono essere di acciaio temprato ) Ebbene , quella fu una invenzione di un mio amico , Beraglia Elio , fresatore stampista provetto , nell'anno 1968 circa nella ditta di Coppo Andrea (stampi) ; tempi di grandi inventi .
почему их надо закаливать? Там нет НИКАКИХ усилий после зажатия тисками. Их можно даже из картона сделать, если эта точность будет желаемой
Queste parallele , vengono sottoposte a duro lavoro di compressione perché il pezzo da serrare in morsa , viene cacciato contro le parallele, dal martello di piombo, per ottenere una perfetta aderenza contro le parallele che stanno sotto , in maniera che non si devono muovere/muoversi ; parliamo di 0.01 centesimo di millimetro max , in orizzontale . @@stalinesssteel4256
@@giannimassarenti7808 "тяжелая работа по сжатию" с применением молотка нужна только для расположения заготовки максимально близко к параллелям. Если посчитать удельное давление на параллели со стороны заготовки во время ударений молотком, то станет известно, что эти удары распределяются по плоскости прикосновения заготовки и параллелей, и являются очень слабыми даже для дюралюминия, не только для простой стали и тем более закаленной. А губки тисков работают вообще в другой плоскости, в которой как бы Вы не прижимали деталь к параллелям, днталь все равно смещается, пусть и незаметно. Так что закалка - мера избыточная и бесполезная
Mi dispiace ma LEI non non faceva punzoni e matrici per stampi ma , noi si .
Sig. Gianni lei mi ha aperto dei ricordi della mia prima gioventù meccanica... le attrezzerie di costruzione stampi, trancia forma lamiera, rettifica con mole a profilo, punzoni, matrici, acciaio temperato, guide... un mosaico meccanico, forse precisione superiore, la si trova nella F1 e in aeronautica, ma tutto nasce dalle macchine utensili.
Mi parli del suo amico Andrea, omonimo di un mio... Non sapevo avesse inventato lui gli "spessori".
Good work
Thank you very much!
2 drill holes in the right size works also and is much faster to made…….
Fantástico y preciso me encanta Gracias 🙏
Unusual sharpening of the cutter. Why?
Do you have a timestamp for me?
Hi I noticed most of your machine tools come from EMCO. Possible to have a workshop tour in future video? Thanks.
Hi, not planned yet, but possible yes. I like the old Austrian machines. They are from the early 80s.
@@randomtechnician Me too was a trained toolmaker in the 80s then we used Deckel and Aciera mill. Then wanted to get an Emco lathe for hobby but way beyond my means :(
@@randomtechnician Hi me too trained as a toolmaker in the 80s. I think I have the manual of your Emco round column mill. If you need it PM over.
@@stewanish Thank you, i have it, too 😅
Why the 2nd angle at 9:20 is 30 degree? The mini bar angle is 40 degree (at 7:52) , and you set the 1st angle is 20 degree (at 8:44), then the 2nd should be 20 degree. What am I missing?
It's the other side of the vise-scale, 50 degree is zero here, so 30 is -20 degree.
что за перевод? Наверное должно быть "Мини токарный станок - сверление БЕЗ СВЕРЛА"
Точно
What is that measuring tool callled that you use to layout
It's called measuring gauge or marking ruler with flat slide(Streichmaß in germany) i use this one:
www.contorion.de/p/holex-streichmass-mit-flachem-schieber-c85173285?q=streichmaß&$ps=1
Bom dia. Tens placa Pead 15mm inteiras. Qual o preço. Obrigado.
Boa noite, não somente sobras
И что я посмотрел ? И для чего ?
Расточные оправки для выполнения точных отверстий любого диаметра
merci de ce partage ..
merci
btw, where did you get that marking/measuring tool?
Do you mean this?:
www.contorion.de/p/holex-streichmass-mit-flachem-schieber-c85173285?$ps=1&measuring_range_max_mm=250&simple_sku=58134045
Расточка это не сверление.
Top
Grazie mille!
Hello where do you buy thèse tiny tools? Greetings
www.bengs-modellbau.de/werkzeug/werkzeuge/mini-bohrstangen-zum-innendrehen?number=3692
Este tornero es niña tiene las uñas muy limpiezitas y arregladas
Привет! Можешь снять видео про фрезерный станок? Это emco fb-2?
Да, это 40-летний FB2, может быть, я сделаю видео, что вас особенно заинтересует?
Boa noite amigo muito bom este ferramenta grande abraço amigo fica com Deus 👌👍👊🥰
Muito obrigado!
A side is not an end
mini tour - perçage sans perçeuse mais pour réaliser les outils faut un tour a métaux MDR!!!!!!!!!!🤔🤔🤔🤔🤔🤔😚😚😚😚😚😚😚
Onde vende esse kit???
Eu só construí uma, peguei as barras chatas daqui: Só construí uma, tirei daqui as barras chatas: www.bengs-modellbau.de/Mini-Bohrstangen-zum-innendreh/36941?
Бронза то клас,а сталь так слабо ? Покажи.
Te voy a dar un "like", pero en este tema soy un neófito. Tantas máquinas me atolondran. Prefiero las cosas menos sofisticadas. Gracias.
Gracias
Зачем так называть ролик,
le titre est faux!! un perçage sens perceuse!!!c'est quoi si ce n'ai pas une perceuse le tour!!!
Непонятно ,что пытается изготовить автор видео
Try exciting bars next time
🤣
????????
???
Schuster....völliger Mist!
Bored.
Thats the problem with boring bars 😅
А где тут мини токарный станок?
he video can be, but you would cut those claws ... ughjjjj