I deeply respect all the HHO community , these people are AMAZING , they are the ones who will change the fossil fuel paradigm ..........GREAT JOB Wood'n Tech
I've also made one alike HHO generator. And because I haven't a powerful transformer,I can only electrolyse water at a electricity of 4.4 ampere, that can only make HHO gases at 0.8ml per second, about 6.5 Joule per second(W), not even match 1/4 of a candle(which has the power of about 30W as I learned). So I collect HHO gases in a balloon, and with a syringe needle in different diameter(I rubbed down the pinpoint, and winded it with some metal wire to help cooling down) , I could make various power of HHO gas-jet. Actually with a syringe needle of 1.0mm diameter(about 20ml HHO gases per second, 160W), I've got a 8cm long yellow gas-jet, which can readily cut the aluminum Coca-Cola bottle in few seconds. Yet with a 0.4mm diameter syringe needle which can achieve a 1cm long gas-jet(2ml HHO per second, 16W), although the temperature is high enough(it can melt a steel needle of 0.6mm diameter), but it can't melt the aluminum Coca-Cola bottle because of it's quick heat transfer. To make a 20ml per second HHO gas directly, it would need an amp of 100, that's not realistic at all.(Unless I separate those plate poles in many cells, and make a series circuit, than I may achieve it without a tremendous amp,and with a higher voltage in replace.This would be a lot of DIY works and take lots of space. I've experienced a explosion too. That happened in the 8cm gas-get experiment, when I was trying to extinguish the flame in water(which succeed readily with smaller gas-jet, and it also works with the 8cm gas-jet when the balloon was still full of gases, but it took seconds of time). It's because of low gas flow rate(the fire transfer rate of HHO is 10m/s, as I've learned. So I think It's better to keep the gas flow rate more than 20m/s for safety,) when the balloon became small and I stopped squeezing the balloon. That didn't hurt me, luckily, but I've got tinnitus for several minute. I'm a Chinese. In writing so much, I'm sharing my experiences(in stead of making video), and, haha, practicing English too! Thank you for reading. I'm going to use my 8cm HHO gas-jet to melt glass bottle with sodium carbonate in it, and see if I can make sodium silicate. Bye-bye!
I think I cried a little over the electrode making part, but apart from that nice job! I'm actually making a dry cell for my school project and the idea of using the console power brick wasn't bad at all, I might actually adapt my design to run on that
My first thought is strictly the pressure from both gasses. If I saw your container correctly, that top is flimsy and the type of thread is not designed for pressure if anything vacuum.
In my opinion, it's not a terrible design flaw as "HHO" is known to self detonate at relatively modest pressures. Venting seems safer than some possible alternatives.
With HHO Generators (electrolysis ) expect high amperage draws. Also if you use only a automotive type battery charger you must have a filtration in parallel with the HHO gen. Large electrolytic capacitor or just simply have a lead acid battery hooked up in parallel with the hho. Pulsating dc does not work well with hho gens.
well done bravo.keep trying.it will worth the effort.be very careful with the presure of the gas.heating is the same,plain water,more volts to test just copy/paste diesel/gas injector .t coonector,1/2pipe,internal rod,ppr cap for t.Good for induction heating,ionic(liquid rezistor),dielectric heating(+ and gnd),tap waterelectrolisis +50/-50V,tapwater heating alternate current (galvanized cast iron pipe,ssteel 304/316 only).goog ack
it's exploded. so it is very dangerous to store oxygen and any flammable gas in the same place. If you are going to store it in the same place, you should use a flashback arrestor. thanks for your video.
this is what happened to people who think its that easy to build, there are lots of factors to consider when building am effecient, safe and reliable hho generator.
I think that is critical because when I tried this the jar exploded with a very loud and deafening bang! I created a flash back arrester with steel wool and copper pipe tubing but it seems there is not enough pressure for the gas to come out and burn! I am not sure what else I could do!
Do a series of tests for different jars, cans, lids, different leads. Do one series of tests at atmospheric pressure, and one series of tests vacuum if you are trying to show how to make from junk items and only some purchased items. I still have the questions about the so-called dry versus wet. Off the top it seemed a wet version is better for ease construction no less than proof of concept although as you know from the common materials aren't sufficient for high stress situations. A small stable bench or sedintary situation the common jars and lids will work. Otherwise you have to step up to steel junk and do some metal fabrications. I speak from some vaporiser construction both on auto and generator but the temperatures, vibrations, conditions exposed to in use, and corrosion problems will require improvements in reactor vessel for either fuel choice. So was the metal from a muffler heat shield or? Scrap yard or purchase. I wish I had even one person to work with me out here I would be so much further and they would have seen some of the shit being done and sickness developing from the building materials toxicity, plus had a chance to relocate by now and get some of my money back out the hides of this damned thriving murderous city. Send in a clean-up crew.
No Cha Cha Cha. Came, You Saw, You Conquered. Wham-Bam Thank You Maam. Ay Ya YAY!!! reminds me how my father taught me jewelry now I'm Goldsmith/Master Jeweler. yes at first I was traumatized LOL watched Stupified in Awe.... EXPLODED LMAO STOP IT YOU'RE KILLING ME... this is HHO Frankenstein Style. love the clear tap fix LMAO. 329 thumbs down are those who don't get it, need their hands to be held every step of the way. i Like, OLE!
Silent movie. I thought we had better technology than that. Keep discovering. You haven't even began to get where lots of people are with hydrogen production yet
my chlorate cell produces more hydrogen than that XD though it does have 65 amps at 5v running through it!! i did test it with a needle hooked up the the gas outlet with a flashback arrestor and yea byproduct is a nice hydrogen torch!! it had no oxygen because that all was being consumed in the cell to convert the salt into NaClO3 then KClO3 by the potassium donor in sol.
Sinubok ako gumawa din nyan kinabit ko sa motor bike ko umandar saglit lang din nag produce uli ako ng fumes sa pangalawang subok pumasok ang apoy sa hose galing sa intake pumotok naman hininto ko na ang pag gawa o imbento jejeje balik nlang ako sa gasolina...kung itotoloy ko baka ako na ang masabugan.. jejeje
Thanks for the reply. I only got so far myself and know I am being blocked by spirit/ghost forces around me some mex, some nypd, some welfare recipients, some medical, some other. If you could sit in my thoughts and we reviewed my memory you could see some of the assaults on me to discredit and defame/ mischaracterise me. If strong you could see the live shit they do to me to make me fail. Then worse, you would realize we live in a kaste that is reverse and tangent engineered why we don't get to build what even our ancestors had paid for and is all off the shelf technology. I know it sounds tuff to believe, but you might be one of the lucky allowed ones and need to come and open the door for us to get back into ourselves. Try a vacuum version to see what the actual parameter changes are for disassociation. Run a series of tests to see which common available electrolytes, metals, plastics, jars, lids, gaskets to get an assortment for people with different material access with low dollar.
You probably couldn't cut the can there was not enough pressure coming from the micro torch... I just wish someone would make a DIY PVC pressure tank with a reinforced steel cage on the outside of the structure to keep it from expanding of course the nozzle itself would have to be much tougher to withstand a good amount of pressure
You'll need two containers connected by a tube so that the electrolyte can pass between them, and then you can collect oxygen or hydrogen from each container
Please don't try to pressurize the Hydrogen/Oxygen mix that is released as it can detonate explosively at 2-3+ atmospheres of pressure (even lower). You most certainly can pressurize hydrogen gas. In a direct current generator, Oxygen is released at the anode (Negative terminal), Hydrogen at the Cathode (Positive terminal). Capturing the Hydrogen alone will allow you to somewhat "Safely" store/pressurize it. If you're planning on going about it, or anyone else is reading your question wondering the same, educate yourself on the dangers first. Again, don't pressurize "HHO" from a homemade generator. I'd also advise against the use of glass if you're just starting out. Rapidly expanding things that are flammable and can self detonate + a sealed glass container that doesn't expand much can make you and those around you quite dead. Like your Uncle's prison cell mate, glass shards can be neat, just not when they're inside of you.
If it's truly Brown's gas, HHO, then it's stable if you vent off the H2 gas. This is because Brown's gas is heavier than air, HOHOHOHOHOHO, a 6 pair hexagonal chain. It's different than either hydrogen or oxygen. It liquifies at -178 C not -183C like Oxygen and much less for hydrogen. Anyway, I'm not sure the pressure. It's in the video linked below but a good ways into it. It's a great video but if you're short on time, look for the part where a guy holds a test tube of fluid. ua-cam.com/video/pa2sjMN8sMc/v-deo.html Good luck to everyone. Be safe but dare to break the so called "laws" of thermodynamics. And physics. And chemistry. But yeah, best not to fool with pressurizing THIS gas. This is a quick and dirty setup, but that's good. It's good to make the point. And, That's tin, not Al. Aluminum likes to react and make AlHO. I'm not sure this would. But that's why he uses tin or one guy said to try stainless. I thought I'd buy perforated metal and agitate the plates. Resonant frequencies??? If someone has read Meyer's patents or his wifes, I think it's in there, but if you know, please tell.
Make your car a hydrogen hi-brid Hho Technology will surprise you! Hho is a mind blowing technology . Cool engine running prolonging engine life and engine oil life with less engine maintainess required🚦 Engine life changer device improve engine performance and increase fuel burning efficiency like a new car!!! 100% fuel will burn in the engine No un burn fuel wastage . Engine will Consume less fuel. Hho system works on petrol, deisel, cng, lpg and lng types gases. Engine runs lighter smoother reducing carbon emissions significantly . Boost engine power and torque . Hho gas reduced engine noice & vibration An efficient hho car kit lower the engine temperature more then 100 degree F. To prevent heat build-up. Hho kits restore better fuel economy. Hho system is very easy and simple to install. Hho solves the engine heating problems automatically!!!. Cleaner engine running. Reducing engine noise due to the faster fuel burning. Hho car kits works nicely requires no modifications in the car engine. No side effects on car engine. Engine start quickly your car battery will charge quickly car AC works better& safe your car battery. make your car a low cost hy-brid. Use a low amps. Hho car kit will work better. You can easily transfer hho kit from one car to another one. Hho kits requires no any modifications in the engine. For more information about this useful technology keep watching hho zafar videos. Or call 03082266179 zafar karachi.
matthew igbinoba it's called electrolysis electrical current past through the water separating oxygen and hydrogen. It's not a chemical reaction , baking soda works just as well
Wyłączamy milczenie. / Włączamy myślenie. Wiedza warta rozdawania. Autorom podziękowania ślę serdeczne. Budzimy iskierki WIEDZY w sobie by je rozdawać.. Sprawdzaj, doświadczaj. Polecam .. ignorancją wspieramy system.. .podaj dalej. My Jesteś MY Zmianą.
Every single test blew up so far. Even with no real reserve in the second jar. I a. Thinking that one negative plate and 9 positives might reduce the oxygen levels. Or it needs to be pressurized with a spark arrestor. I could use it as is in a vehicle though. An old one. New ones would detect oxygen level with sensor and have no improvement. It would run good on only hydrogen supplement.
Уважаемый ваша сборка не верна. Контактные пластины между парой разной полятности должна составлять зазор не более 1,2 мм,а промедутность между парами составляет 8 - 10 мм.Изменяя значение в расстоянии,приводит к совершению ошибочных доводов. просмотрите мои видео сюжеты,где я предоставляю информацию для интересующихся людей,и ещё реактор собирают емкостной формы.С ув.Wold.
Well the good news is YOU'RE too INCOMPETENT to make anything too dangerous, you only present a danger in one way, every once in a while - you'll scare the crap out of your dog/cat.
I deeply respect all the HHO community , these people are AMAZING , they are the ones who will change the fossil fuel paradigm ..........GREAT JOB Wood'n Tech
Wow thank you for the encouragement!
Legendary comment and thanks bro:)
I've also made one alike HHO generator. And because I haven't a powerful transformer,I can only electrolyse water at a electricity of 4.4 ampere, that can only make HHO gases at 0.8ml per second, about 6.5 Joule per second(W), not even match 1/4 of a candle(which has the power of about 30W as I learned).
So I collect HHO gases in a balloon, and with a syringe needle in different diameter(I rubbed down the pinpoint, and winded it with some metal wire to help cooling down) , I could make various power of HHO gas-jet. Actually with a syringe needle of 1.0mm diameter(about 20ml HHO gases per second, 160W), I've got a 8cm long yellow gas-jet, which can readily cut the aluminum Coca-Cola bottle in few seconds. Yet with a 0.4mm diameter syringe needle which can achieve a 1cm long gas-jet(2ml HHO per second, 16W), although the temperature is high enough(it can melt a steel needle of 0.6mm diameter), but it can't melt the aluminum Coca-Cola bottle because of it's quick heat transfer.
To make a 20ml per second HHO gas directly, it would need an amp of 100, that's not realistic at all.(Unless I separate those plate poles in many cells, and make a series circuit, than I may achieve it without a tremendous amp,and with a higher voltage in replace.This would be a lot of DIY works and take lots of space.
I've experienced a explosion too. That happened in the 8cm gas-get experiment, when I was trying to extinguish the flame in water(which succeed readily with smaller gas-jet, and it also works with the 8cm gas-jet when the balloon was still full of gases, but it took seconds of time). It's because of low gas flow rate(the fire transfer rate of HHO is 10m/s, as I've learned. So I think It's better to keep the gas flow rate more than 20m/s for safety,) when the balloon became small and I stopped squeezing the balloon. That didn't hurt me, luckily, but I've got tinnitus for several minute.
I'm a Chinese. In writing so much, I'm sharing my experiences(in stead of making video), and, haha, practicing English too!
Thank you for reading. I'm going to use my 8cm HHO gas-jet to melt glass bottle with sodium carbonate in it, and see if I can make sodium silicate. Bye-bye!
Ever see a grown man naked?
Do you have some book reference?
Stanley meyer use a super conductor
@@marysuetells9173 could you explain in a little more detail?
Great vid! nice to see your thumb recovered
Haha thanks
you my friend are a Genius, thanks for the vid
HAHAHAHAHA You're Picture, Priceless. i Like, OLE!
I think I cried a little over the electrode making part, but apart from that nice job! I'm actually making a dry cell for my school project and the idea of using the console power brick wasn't bad at all, I might actually adapt my design to run on that
Super idea, but little danger construction.
Yes it was to dangerous, I built a safer version after that
It is realy home made generator. Congratulation. your wife enjoy it ha ha ha. Tank you. Ana
My first thought is strictly the pressure from both gasses. If I saw your container correctly, that top is flimsy and the type of thread is not designed for pressure if anything vacuum.
You are totally right, I am working on a better version that can withstand higher pressures.
In my opinion, it's not a terrible design flaw as "HHO" is known to self detonate at relatively modest pressures. Venting seems safer than some possible alternatives.
Really enjoy how this video is sped up !!
Thanks my friend, you're really an engineer!
Good luck !
Thanks, soon enough I will officially be an engineer :-)
With HHO Generators (electrolysis ) expect high amperage draws. Also if you use only a automotive type battery charger you must have a filtration in parallel with the HHO gen. Large electrolytic capacitor or just simply have a lead acid battery hooked up in parallel with the hho. Pulsating dc does not work well with hho gens.
Explain what you are using and for what purpose
well done bravo.keep trying.it will worth the effort.be very careful with the presure of the gas.heating is the same,plain water,more volts to test just copy/paste diesel/gas injector .t coonector,1/2pipe,internal rod,ppr cap for t.Good for induction heating,ionic(liquid rezistor),dielectric heating(+ and gnd),tap waterelectrolisis +50/-50V,tapwater heating alternate current (galvanized cast iron pipe,ssteel 304/316 only).goog ack
Great video.
I think I would have liked your video If you explained what you were doing
Hand pointed "gimme your job"
I know a guy called Nathan he used to drill like that now people call him Nathumb...
it's exploded. so it is very dangerous to store oxygen and any flammable gas in the same place. If you are going to store it in the same place, you should use a flashback arrestor. thanks for your video.
I bet the holes in your plates would help alot
this is what happened to people who think its that easy to build, there are lots of factors to consider when building am effecient, safe and reliable hho generator.
Simple and good idea to make easily good job brother
Why not doubled the negative plate since it produces double hydrogen?
jajajajajajaja comenzó con las manos buenas y se reventó una
juas juas juas fiatta
What happened to your left thumb between 1:30 and 1:36?
Your comment made me LMAO because I was wondering the same thing!
Very observant:-]
Where did he put the flashback arrestor ?
Hahaha! You need a flash back arrester.
I think that is critical because when I tried this the jar exploded with a very loud and deafening bang! I created a flash back arrester with steel wool and copper pipe tubing but it seems there is not enough pressure for the gas to come out and burn! I am not sure what else I could do!
heeeey, thats pretty good! i've tried multiple times to produce hho with a mason jar and modified lid... i keep getting leaks though:/
Gas always keep on leaking through holes which we can't see if we want to.
Do a series of tests for different jars, cans, lids, different leads. Do one series of tests at atmospheric pressure, and one series of tests vacuum if you are trying to show how to make from junk items and only some purchased items.
I still have the questions about the so-called dry versus wet. Off the top it seemed a wet version is better for ease construction no less than proof of concept although as you know from the common materials aren't sufficient for high stress situations. A small stable bench or sedintary situation the common jars and lids will work. Otherwise you have to step up to steel junk and do some metal fabrications. I speak from some vaporiser construction both on auto and generator but the temperatures, vibrations, conditions exposed to in use, and corrosion problems will require improvements in reactor vessel for either fuel choice.
So was the metal from a muffler heat shield or? Scrap yard or purchase. I wish I had even one person to work with me out here I would be so much further and they would have seen some of the shit being done and sickness developing from the building materials toxicity, plus had a chance to relocate by now and get some of my money back out the hides of this damned thriving murderous city. Send in a clean-up crew.
La chapa de los tambores de las lavadoras contiene plata también.
what is the metal you used as rods ? aluminium? steel?
You should have sanded the electrodes so that they are having a even bigger surface.
But overall a really good video and idea
+Max Bambusman thank you :-)
No Cha Cha Cha. Came, You Saw, You Conquered. Wham-Bam Thank You Maam. Ay Ya YAY!!! reminds me how my father taught me jewelry now I'm Goldsmith/Master Jeweler. yes at first I was traumatized LOL watched Stupified in Awe.... EXPLODED LMAO STOP IT YOU'RE KILLING ME...
this is HHO Frankenstein Style. love the clear tap fix LMAO. 329 thumbs down are those who don't get it, need their hands to be held every step of the way. i Like, OLE!
question is. how quickly do your plates break down from the HHO generation?
Heat themred hot, put them in lye. They should turn black, be protected from breaking and be conductive.
You better lay off the coffee.
Lol I like to imagine this guy doesnt speed his video up
Silent movie. I thought we had better technology than that. Keep discovering. You haven't even began to get where lots of people are with hydrogen production yet
Can i use metal screws to hold the plates
Build it bigger for more gas.
Yes ideally!
Is there a file to be worked on from the materials and how to use?
my chlorate cell produces more hydrogen than that XD
though it does have 65 amps at 5v running through it!!
i did test it with a needle hooked up the the gas outlet with a flashback arrestor and yea byproduct is a nice hydrogen torch!!
it had no oxygen because that all was being consumed in the cell to convert the salt into NaClO3 then KClO3 by the potassium donor in sol.
Heyy man can we have a convo plss.. I'm making a project and I think ur chlorate cell can help me..
Gotta be extra careful with storage!
Sinubok ako gumawa din nyan kinabit ko sa motor bike ko umandar saglit lang din nag produce uli ako ng fumes sa pangalawang subok pumasok ang apoy sa hose galing sa intake pumotok naman hininto ko na ang pag gawa o imbento jejeje balik nlang ako sa gasolina...kung itotoloy ko baka ako na ang masabugan.. jejeje
Thanks for the reply. I only got so far myself and know I am being blocked by spirit/ghost forces around me some mex, some nypd, some welfare recipients, some medical, some other. If you could sit in my thoughts and we reviewed my memory you could see some of the assaults on me to discredit and defame/ mischaracterise me. If strong you could see the live shit they do to me to make me fail. Then worse, you would realize we live in a kaste that is reverse and tangent engineered why we don't get to build what even our ancestors had paid for and is all off the shelf technology. I know it sounds tuff to believe, but you might be one of the lucky allowed ones and need to come and open the door for us to get back into ourselves. Try a vacuum version to see what the actual parameter changes are for disassociation. Run a series of tests to see which common available electrolytes, metals, plastics, jars, lids, gaskets to get an assortment for people with different material access with low dollar.
Oh that's nice. Now put in a car already 💁♂️
You probably couldn't cut the can there was not enough pressure coming from the micro torch... I just wish someone would make a DIY PVC pressure tank with a reinforced steel cage on the outside of the structure to keep it from expanding of course the nozzle itself would have to be much tougher to withstand a good amount of pressure
Don't pressurize the gas from an "HHO" generator, it can self detonate.
Great, how do I make one that collects hydrogen and oxygen separately?
You'll need two containers connected by a tube so that the electrolyte can pass between them, and then you can collect oxygen or hydrogen from each container
Can we connect this to any 2 wheeler.please explain.
how can you collect and store the gas safely afterwards?
+corgidog quirke yeah that's an actual problem since you can't pressurise hydrogen
Please don't try to pressurize the Hydrogen/Oxygen mix that is released as it can detonate explosively at 2-3+ atmospheres of pressure (even lower). You most certainly can pressurize hydrogen gas. In a direct current generator, Oxygen is released at the anode (Negative terminal), Hydrogen at the Cathode (Positive terminal). Capturing the Hydrogen alone will allow you to somewhat "Safely" store/pressurize it. If you're planning on going about it, or anyone else is reading your question wondering the same, educate yourself on the dangers first.
Again, don't pressurize "HHO" from a homemade generator. I'd also advise against the use of glass if you're just starting out. Rapidly expanding things that are flammable and can self detonate + a sealed glass container that doesn't expand much can make you and those around you quite dead. Like your Uncle's prison cell mate, glass shards can be neat, just not when they're inside of you.
If it's truly Brown's gas, HHO, then it's stable if you vent off the H2 gas. This is because Brown's gas is heavier than air, HOHOHOHOHOHO, a 6 pair hexagonal chain. It's different than either hydrogen or oxygen. It liquifies at -178 C not -183C like Oxygen and much less for hydrogen.
Anyway, I'm not sure the pressure. It's in the video linked below but a good ways into it. It's a great video but if you're short on time, look for the part where a guy holds a test tube of fluid. ua-cam.com/video/pa2sjMN8sMc/v-deo.html
Good luck to everyone. Be safe but dare to break the so called "laws" of thermodynamics. And physics. And chemistry.
But yeah, best not to fool with pressurizing THIS gas. This is a quick and dirty setup, but that's good. It's good to make the point.
And, That's tin, not Al. Aluminum likes to react and make AlHO. I'm not sure this would. But that's why he uses tin or one guy said to try stainless. I thought I'd buy perforated metal and agitate the plates. Resonant frequencies??? If someone has read Meyer's patents or his wifes, I think it's in there, but if you know, please tell.
Can you tell me why it's explode?
The flame came back up the tube and set fire to the generator
Make your car a hydrogen hi-brid Hho Technology will surprise you! Hho is a mind blowing technology . Cool engine running prolonging engine life and engine oil life with less engine maintainess required🚦
Engine life changer device improve engine performance and increase fuel burning efficiency like a new car!!! 100% fuel will burn in the engine No un
burn fuel wastage . Engine will Consume less fuel. Hho system works on petrol, deisel, cng, lpg and lng types gases.
Engine runs lighter smoother reducing carbon emissions significantly . Boost engine power and torque . Hho gas reduced engine noice & vibration
An efficient hho car kit lower the engine temperature more then 100 degree F. To prevent heat build-up. Hho kits restore better fuel economy. Hho system is very easy and simple to install. Hho solves the engine heating problems automatically!!!.
Cleaner engine running. Reducing engine noise due to the faster fuel burning. Hho car kits works nicely requires no modifications in the car engine. No side effects on car engine.
Engine start quickly your car battery will charge quickly car AC works better& safe your car battery. make your car a low cost hy-brid. Use a low amps. Hho car kit will work better. You can easily transfer hho kit from one car to another one. Hho kits requires no any modifications in the engine. For more information about this useful technology keep watching hho zafar videos. Or call 03082266179 zafar karachi.
Is it a time lapse or is he actually goin this fast??
The footage is sped up
Un prof m'avait appris que la lame de scie on la paye d'un bout à l'autre. Donc l'utiliser sur toute sa longueur.
are these Fighting Words, Partner ????? or Compliments, Grrrr..... OLE!
Pravasi nice lohitha
What mixture did you use for the liquid
nice idea
That's true .very good 101%
Taasss.... loco. are you crazy
Why all this hard and elaborate task simply to produce hydrogen by chemical reaction!!!!!!!
matthew igbinoba it's called electrolysis electrical current past through the water separating oxygen and hydrogen. It's not a chemical reaction , baking soda works just as well
Motorbike runs on water | HHO | hydrogen gas generator | without petrol | with proof
#Raselhomemadecreator
lol... if you whant more more more gaz ... use only a stainless steel, not a aluminium , and a distilled water ( for no mineral ! )
Man you can mix sodium carbonate because can make CO2 its too risky
HHO is water . The name is H!
Hi, there. I never understood a word of that, next time in plain English please. Nice vid.
Greate job .......keep doing that
Wyłączamy milczenie. / Włączamy myślenie. Wiedza warta rozdawania. Autorom podziękowania ślę serdeczne. Budzimy iskierki WIEDZY w sobie by je rozdawać.. Sprawdzaj, doświadczaj. Polecam .. ignorancją wspieramy system.. .podaj dalej. My Jesteś MY Zmianą.
Nozzle was too small, thats why it kept breaking
Every single test blew up so far. Even with no real reserve in the second jar. I a. Thinking that one negative plate and 9 positives might reduce the oxygen levels. Or it needs to be pressurized with a spark arrestor. I could use it as is in a vehicle though. An old one. New ones would detect oxygen level with sensor and have no improvement. It would run good on only hydrogen supplement.
quote "every single test blew up so far" at least he didn't throw in the towel. OLE!
you planning on making of these? be careful about using stainless steel as electrodes. it leaches hexavalent chromium ions
Steel plate where u got?
narvekar1 its a jar from washing machine its a prochrome-stainless steel ! Btw you can you couple spoons
It isnt flash back arrestor its just a bubbler
The bubbles are meant to separate the gas flow in small portions to arrest the flashback
Уважаемый ваша сборка не верна. Контактные пластины между парой разной полятности должна составлять зазор не более 1,2 мм,а промедутность между парами составляет 8 - 10 мм.Изменяя значение в расстоянии,приводит к совершению ошибочных доводов. просмотрите мои видео сюжеты,где я предоставляю информацию для интересующихся людей,и ещё реактор собирают емкостной формы.С ув.Wold.
Please I need HHO Gas burners for cooking
Wtf hydrogen ain't for cooking use natural gas or propane or something
Your geometrical'cell IS so Bad the ohmical résistance IS great
does anyone know why this darn system doesn't add some comments although I pressed send? it stalls on my email accounts also.
flashback arrestor :)
I had one but it didn't work properly.
How did the flashback get to the cell since it looked like you had 2 flashback arrestors?
Awesome
Thanks
Did you dabble into any of the alleged health gain claims or regeneration whereby you built anything and ran a series of valid tests? 347-794-4124
stainless steel releases toxic hexavalent chromium
No cristaux soude. Yes sel= Sal
What a fuck!? 16 amp that to draw on tree??????
You don't understand.
@@JeanDeBailliencourt that you has to say me?
@@JeanDeBailliencourt Да сам ты Олень!
where can i get sodium carbonate Crystals?
+ikbal toor in the house cleaning section of any shop
Materials list?
I think thats a power problem
nice
cuidado con el retroceso de la llama
لم نتعرف علي المواد المستخدمه اما العمليه فهي جيده ونسبة الخطوره كم لماذا لا تتكلم
Waht is powder nam
Baking soda can be used
Les Canettes de coca ne sont pas en alu .
es muy pequeño el hoyo de la aguja menso.
simon, pero se avento
ur thumbs up man
bro use flash back arrester
Very sloppy work man
Show de bola beautiful Love
could i use aliminum plates insted of stainless steel
+watsupp Btiches sure
no, i've tried it and it didn't work
watsupp Btiches If you use aluminium you need way more amp so not efficiënt at all
copper sheets, stainless steel scourng pads, stainless steel utensils The World is Your Oyster Carpe Diem. OLE!
Hay problema de poco voltaje y malas conexiones.
eso es lo de menos
lol 😁 love that video
Its not aluminum .. Its tin
+DEEPAK DILIP no its aluminium
+DEEPAK DILIP no its aluminium
+DEEPAK DILIP no its aluminium
+DEEPAK DILIP no its aluminium
Yes but from what did you get this piece of metal from you cut with the snips?
It exploded
hi
Pardzo fajne
Well the good news is YOU'RE too INCOMPETENT to make anything too dangerous,
you only present a danger in one way, every once in a while - you'll scare the crap out of your dog/cat.
😯