Great video - did the trick for me on the rear door trim. Just have to remember to leave the inside rubber seal dangling untill the trim is in place and then hold glass and squeeze the rubber down between window and new trim. Thanks Vlad!
I had a bent pillar and top moulding in the rear window of my 2010 VW Jetta caused by an accident with the previous owner. The bent pillar allowed air to whistle through at high speeds. While it has performed as a good commuter car, it really wasn't worth it to put a lot of money into it. With the help of your video, I was able to remove the pillar and trim and found that the steel flange holding the trim at the top of the door was bent. This caused the trim piece to bend downwards and create the open hole. All I needed to do was straighten out the top flange with a few taps of a hammer, then reshape the pillar and put everything back together again following your instructions. It cost me nothing! I wouldn't have attempted it had I not seen your video! You have saved me time and money! Thank you, Vlad!
Merci pour ta vidéo grâce à j'ai pu faire le nécessaire pour les plaquettes de frein de ma voiture et éviter de sortir les sous sous 😅. Si jamais tu as d'autres vidéo ! Je prends 😊
I was unable to get the side wheather stripping back in and had to cut the lower portion off to get the window closed. Now I need to take it to a shop and have them replace the seal.
On my mkv Jetta had to remove the inside front door panel and the window inside sweep moulding. I have a picture but don't know how to share it on here?
Mk5 Jetta is similar, rear door panel is easy, but front panel is a bear to get the rubber back in there. Have to take the inside door panel off. Is there a easier way?
Leave the bottom trim off and insert the rubber on an angle to miss the window regulator mechanism below. Don’t be fooled thinking the window up/down will help. Or, using any type of lubricant.
Great video - did the trick for me on the rear door trim. Just have to remember to leave the inside rubber seal dangling untill the trim is in place and then hold glass and squeeze the rubber down between window and new trim. Thanks Vlad!
You welcome Robin! Appreciate it! ^_^
I had a bent pillar and top moulding in the rear window of my 2010 VW Jetta caused by an accident with the previous owner. The bent pillar allowed air to whistle through at high speeds. While it has performed as a good commuter car, it really wasn't worth it to put a lot of money into it. With the help of your video, I was able to remove the pillar and trim and found that the steel flange holding the trim at the top of the door was bent. This caused the trim piece to bend downwards and create the open hole. All I needed to do was straighten out the top flange with a few taps of a hammer, then reshape the pillar and put everything back together again following your instructions. It cost me nothing! I wouldn't have attempted it had I not seen your video! You have saved me time and money! Thank you, Vlad!
Excellent, great video demonstration.
Merci pour ta vidéo grâce à j'ai pu faire le nécessaire pour les plaquettes de frein de ma voiture et éviter de sortir les sous sous 😅.
Si jamais tu as d'autres vidéo ! Je prends 😊
Thanks for uploading! I've been looking for this everywhere! 🙂
As clear as it gets - thanks for posting!
Great video! sliding the glass channel rubber back is a bit of a fiddle, when you come to put everything back!
Haven't seen a detailed video on this topic so I decide to make my own one! Hope it will be helpful!
Have you got one putting it back?
3 years on and it’s helped me immensely👌😎
Muchísimas gracias tu video me sirvió un montón.
saved me so much time ! i thought they where stuck on !
man you saved me some money :)
You made my day! thanks :)
You welcome :)
Great video. Thanks for taking the time to show this.
Do you have a video of you putting it back together again?
Thank you soooo much
Thanks 👍
Thanks!
You Fkin legend thank you.
You welcome dude! )))
I was unable to get the side wheather stripping back in and had to cut the lower portion off to get the window closed. Now I need to take it to a shop and have them replace the seal.
Off to but some new trim to replace rusty existing. Ta very much for methodology
On my mkv Jetta had to remove the inside front door panel and the window inside sweep moulding. I have a picture but don't know how to share it on here?
Mk5 Jetta is similar, rear door panel is easy, but front panel is a bear to get the rubber back in there. Have to take the inside door panel off. Is there a easier way?
Thanks. Is it the same on the MK5 3 door?
Can we have a video on how to put a new one in after removing the old one please? Anyone know where to buy a replacement? Cheers!
Any idea where I can find this piece for a Tiguan 5N from 2015?
now how you put it back lol
Au ceva cod pe ele :D sau stii codul lor?
Where i can buy that piece??
How in the heck were the screws that easy for you?! I stripped 2 then gave up for the day
Did you try WD-40?
Jessica H I think I might have to use it once u put everything together
Same for 2007 Vw Jetta????
can someone please tell me how to build the seal back ? i can't haha
Thanks, but I can't get the rubber bands back in... Now what?
Leave the bottom trim off and insert the rubber on an angle to miss the window regulator mechanism below. Don’t be fooled thinking the window up/down will help. Or, using any type of lubricant.
Just try to guide them with a thin metal stick (the way I have done it).
multam
Cu placere :)