How To Replace Front Axle Shaft 2007-16 GMC Acadia
Вставка
- Опубліковано 23 сер 2024
- Buy Now!
New CV Axle Shaft from 1AAuto.com 1aau.to/ib/1AAC...
A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications. This video shows you how to install one in your 2007-2016 GMC Acadia.
• Check here for more videos on the 2007-16 GMC Acadia: • GMC Acadia 2007-16 1st...
This process should be similar on the following vehicles:
2007 GMC Acadia
2008 GMC Acadia
2009 GMC Acadia
2010 GMC Acadia
2011 GMC Acadia
2012 GMC Acadia
2013 GMC Acadia
2014 GMC Acadia
2015 GMC Acadia
2016 GMC Acadia
Tools you will need:
• Pocket Screwdriver
• Pry Bar 1aau.to/oa/1AXA...
• 10mm Socket 1aau.to/oa/1AXA...
• 22mm Socket 1aau.to/oa/1AXA...
• 24mm Socket
• 34mm Socket 1aau.to/oa/1AAS...
• Air Compressor
• Dead Blow Hammer 1aau.to/oa/1AXA...
• 1/2 Inch Air Impact Gun 1aau.to/oa/1AXA...
• Ratchet 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• Gloves 1aau.to/oa/1AXS...
• Safety Glasses 1aau.to/oa/1AXA...
• Center Punch 1aau.to/oa/1AXA...
• Drain Pan 1aau.to/oa/1AXA...
• Sledge Hammer 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
GMC Acadia 2007-16 1st Generation: • GMC Acadia 2007-16 1st...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Excellent video. To the point. No extra nonsense. Thanks buddy!
Great video I like how you skipped the unnecessary parts like taking the wheel off and got down to the meat of how to change the axle
Thanks for the video. Surprisingly, not that complicated of a job.
Good video. Thanks. Do I need to get an alignment afterwards?
No
Why not show or mention drip pan and replacing fluid?
Looks like you sheered off one of the bolts holding on the steer knuckle, didn’t mention that: was that due to too much torque at 144lb?
What to do when the hub is completely fueled to the axle? I have soaked it in pb blaster for 3 days. Tried gear puller, sledge hammer. Axle won’t come out of the hub.
Should the cv on transmission side have about a 3 inch gap or should there be less of a gap. Havent changed anything yet but there heavy vibration during medium and heavy throttle but quits when throttle is reset and barely pressed (doesnt matter the speed) i suspect its a cv axle pulled out some and slipping. Thank you
Thank you
Good video. Thanks.
Any idea how much transmission fluid is needed to replace what comes out when you pull the driver side?
Did you ever find out? I'm getting ready to do the Sam's thing and wondered how much uid is lost
Where exactly am i suppose to pry on axle to pop it off
how do you remove the square end off the CV axle to replace the square piece?
how do you remivevthe square piece off of the CV axel
I tightened my wheel axle nut to 150ft lbs
Hi - just did tie rods, lower control arms, struts and sway bar links with alignment last weekend but still have vibration and click on turns on passenger side. I don’t want to lose my brand new alignment- rather drop the control arm is possible- anyone try it that way?
I order the CVs from you guys as well.
Great video... I'll try this tomorrow. I believe it will save me a lot of time & money. Thank you very much!!!
Why my gmc acadia 2011 averytime when i turn the Sterling wheel the front sleep and make noise
Then you need to grease or change your CV Axle Assembly
He didn’t even get dirty lol
👍👍
No help because you don’t show exactly where we’re prying out the axle
pry on the backside of the cv; it's a big can. if you can't figure that out, you should probably call a mechanic.
You should see a big brown can looking piece at the end of the cv. I stuck a prybar close to where I thought it was from under the car then looked to see if I could see the the tip of the pry bar behind that brown can and then it popped of real easy once I was back under the car in the front.
Where is the seal??????
✅️
Thank you