💰Thanks to k-racingshop.com/ for sponsoring this video, use the code RED15 to get a discount on Rotax Max products! Tutorial on how to get the maximum discount: ua-cam.com/video/LoNKb7UQ5Pk/v-deo.html ✅ Join the Discord server: discord.gg/dE2SCedWdv 📸 Follow me on Instagram: instagram.com/bramossewaarde/ 🎵 Follow me on TikTok: www.tiktok.com/@bramossewaarde
Noticed your rear axle bearings are facing the same way. In my opinion they should be opposite, that means both pointing either inwards or outwards. Otherwise there will be small difference in stiffness on the right/left side 😊
I thought the same but thats how they come from the otk factory so i assume they know more than me. Plus i think the one bearing on the engine side is turned the other way to account for the extra weight of the engine on that side
They may lock up or spin roughly. I got dirty water into my spindle while driving and didnt clean it up and it completly locked the bearing. Get some wd-40 in there!
Hey red be careful with the exhaust mount. We ran it in my team and did a test where we found out that the opposite of what you were saying about the mount. Because your exhaust is mounted with rubber bushings and the right mount isn't permanent mounted on (only with springs) it gives it the flexibility to the point where the kart isn't stiffened by the mount. This mount you put on is directly clamping the two pipes on the chassis and therefore increasing the stiffness of the chassis. You can run a test and see for yourself how it works.
Bro that new exhaust bracket is going to stiffen the rear even more as you are clamping to tubes together. The original otk way is best plus you have the rubber bushes on the exhaust. New system is deffo a no 👎 Also little tip…spray dasty all over the radiator and jet wash it, will look like new after
13:03 I need to say this on Spanish Buenas niños y niñas hoy les tengo una sorpresa. WD40 hoy patrocina este video siempre y cuando encuentre al menos 20 usos para el WD40 donde intentaremos reconstruir una moto y si participas en el concurso de restauración de motos anual de WD40 podrías ser el ganador de nada más y nada menos que 5000 pavinis así que empecemos de una vez Y DENTRO INTRO!!! --- Majes en Motos
please stop using wd40 ;-) it is to loosen corrosion, not for greasing whatsoever. WD40 can harm you plastic parts. Get a multioil from a proper brand. Keep up your content :-)
💰Thanks to k-racingshop.com/ for sponsoring this video, use the code RED15 to get a discount on Rotax Max products! Tutorial on how to get the maximum discount: ua-cam.com/video/LoNKb7UQ5Pk/v-deo.html
✅ Join the Discord server: discord.gg/dE2SCedWdv
📸 Follow me on Instagram: instagram.com/bramossewaarde/
🎵 Follow me on TikTok: www.tiktok.com/@bramossewaarde
I hate when I use up to 8 hours on cleaning my kart, then just throws it in the dirt first practice heat. I did that last week :)
8 hours? You gotta be the shiniest mofo out there
first time I've seen the carb needle protector. pretty cool.
They're really nice
i've had experiences where that fuel filter was generating air bubbles in the fuel line and the engine was cutting power
Oh I've never had that. Fuel filters are mandatory anyways
wish i had my own kart but maybe in the future
Muy bueno el video! Que diferencia hay a la
Vista para distinguir si un chasis otk es año 2022 o 2023?
Great video again 😉👍🏻🏁
Why you don’t blow air with the air gun to dry it ?
Noticed your rear axle bearings are facing the same way. In my opinion they should be opposite, that means both pointing either inwards or outwards. Otherwise there will be small difference in stiffness on the right/left side 😊
tuning, if you know what you do
I thought the same but thats how they come from the otk factory so i assume they know more than me.
Plus i think the one bearing on the engine side is turned the other way to account for the extra weight of the engine on that side
Good job young man,good job ✌️☕️☕️
is it safe to spray the battery like that too?
The battery was not on the kart, but it should be as you can also drive in the wet
When I did it my mag parts got a wierd white film on it I don’t know why
Question what happens if I get water in the front spindle bearings while cleaning
They may lock up or spin roughly. I got dirty water into my spindle while driving and didnt clean it up and it completly locked the bearing. Get some wd-40 in there!
@@sixtenallingersandgren6674 ok thanks
Yeah it's pretty harmless. Just make sure to put some WD40 on there often
Good vidéo thanks for your tips 😀
Hello from France🇫🇷 il love your UA-cam Chanel 😃😁
Hello, thanks!
What’s Your training program?
Karting... That's literally it lol
Hi Red!
I am going to check out this week's race. Are you alright if I come to say hi? :)
Of course man, feel free to do so!
Hey red be careful with the exhaust mount. We ran it in my team and did a test where we found out that the opposite of what you were saying about the mount. Because your exhaust is mounted with rubber bushings and the right mount isn't permanent mounted on (only with springs) it gives it the flexibility to the point where the kart isn't stiffened by the mount. This mount you put on is directly clamping the two pipes on the chassis and therefore increasing the stiffness of the chassis. You can run a test and see for yourself how it works.
You could solve it with loosing the nuts a bit from one of the mount at the slotted hole
Bro that new exhaust bracket is going to stiffen the rear even more as you are clamping to tubes together. The original otk way is best plus you have the rubber bushes on the exhaust. New system is deffo a no 👎
Also little tip…spray dasty all over the radiator and jet wash it, will look like new after
Hello, how does the bar-type device work for the exhaust pipe, where did you buy it?
The ln kart has arrived
It has :)
13:03 I need to say this on Spanish
Buenas niños y niñas hoy les tengo una sorpresa.
WD40 hoy patrocina este video siempre y cuando encuentre al menos 20 usos para el WD40
donde intentaremos reconstruir una moto
y si participas en el concurso de restauración de motos anual de WD40
podrías ser el ganador de nada más y nada menos que 5000 pavinis
así que empecemos de una vez Y DENTRO INTRO!!!
---
Majes en Motos
please stop using wd40 ;-) it is to loosen corrosion, not for greasing whatsoever. WD40 can harm you plastic parts. Get a multioil from a proper brand. Keep up your content :-)
Good video
Are you going to the gym bro, you’re getting big like schwarzenegger😂
Nope that's all karting mate
And whats your job?
I work for my dad, and UA-cam :)
@@RedExions omg you answered me i drive gokart and your my idol