Ygmfmh- Under normal conditions we would use water and suggest it to all of our customers. This particular customer asked for a dry demonstration. If you stand up wind its not too bad, but would not recommend running like this for a long time. I have posted a link in the "about" section to a video of one of our hammer mills running wet and you will see there is no dust. It makes a great slurry to run directly on to a shaker table or down a sluice box! Thanks for the comment.
I am car mechanic, I have good suggestion for you If you wanna extended life of diesel or gasoline engine in such dusty working environment add two stage air cleaner that you can find on farm tractor first is dry separator with glass mushroom syclon and second is wet (oil) cleaner, Also its better you connect 3-4 inch flexible hose (like vacuum cleaner hose) and connect two stage air filter 2-3 yards away from engine, and you need to clean it each week,or 100 hours,
Would it be possible to construct one machine like this for breaking down not only pistons but engine heads, intake manifolds, parts of the block.. I need a way of recycling and breaking down aluminium to a 8-6 mesh powder before seperation and melting. =)
More important is the pulverized rock is being slug into the screen rather than armor hence the screen will prematurely wear to failure. Only a combo wet/dry hammer mill is a must. Dont forget armor wear plates unless you want the body to fail early.
Great product! However how did you break down or crush the initial stone sizes of approximately 150mm down to the 13 mm partical size that was crushed in this video?
+Richard Vincent Thanks for the question. We used a jaw crusher. You can see a video of one of our jaw crushers here: ua-cam.com/video/0bSmO9N25Yk/v-deo.html Also please check out our website for more details: www.mbmmllc.com/
Hi Bryan, If you can send me an email at MBMMLLC@gmail.com I can send you a full price list and info sheet on all our equipment and hammer mills. The 50 mesh minus was the smallest screen I had at the time of the test. There is a lot of material that is smaller than 50 mesh, too. Fine cooking flour is between 100 and 200 mesh for comparison. Thanks for posting.
Hello Cayajo- Please send us an email at MBMMLLC@gmail.com and we can discuss the details of getting you a machine shipped to Peru. I have a past customer / importer in Ecuador who may be able to handle all the shipping for you on the machine. Thanks, Jason
Very impressive, although some other impressions are also hard to miss: That this is not an environmentally friendly method with regards to it producing dust as a final product AND as loads of fine particles in the air, and that it is not quite wise of the dudes operating the mill to not wear breathing protection..
Ygmfmh-
Under normal conditions we would use water and suggest it to all of our customers. This particular customer asked for a dry demonstration. If you stand up wind its not too bad, but would not recommend running like this for a long time. I have posted a link in the "about" section to a video of one of our hammer mills running wet and you will see there is no dust. It makes a great slurry to run directly on to a shaker table or down a sluice box!
Thanks for the comment.
Glad you published this particular comment.... I WAS going to mention some severe lung problems in the future if not wearing a mask...
I am car mechanic,
I have good suggestion for you
If you wanna extended life of diesel or gasoline engine in such dusty working environment add two stage air cleaner that you can find on farm tractor first is dry separator with glass mushroom syclon and second is wet (oil) cleaner,
Also its better you connect 3-4 inch flexible hose (like vacuum cleaner hose) and connect two stage air filter 2-3 yards away from engine, and you need to clean it each week,or 100 hours,
Great! Thanks!
Thanks!
Would it be possible to construct one machine like this for breaking down not only pistons but engine heads, intake manifolds, parts of the block.. I need a way of recycling and breaking down aluminium to a 8-6 mesh powder before seperation and melting. =)
How long do your hammers last. What material are they made from?
This is great! How often to change the beaters?
Sir is it possible to crush clam shell with this mill.if not could you suggest for any mill
Gracias por mostrarnos su diseño . Es una excelente maquina. Solo veo una deficiencia en el diseño y es la cantidad de polvo que va directo al motor.
Thank you for your comment and for watching our videos!
HOW much would like to purchase
Is it spinning counter clockwise? Most I've seen spin clockwise and it creates a vacuum so no dust in your face it pumps it out the bottom
More important is the pulverized rock is being slug into the screen rather than armor hence the screen will prematurely wear to failure. Only a combo wet/dry hammer mill is a must. Dont forget armor wear plates unless you want the body to fail early.
From which country is this machine can it be delivered in india
Cuáles son las dimensiones del molino? Cuántas toneladas la hora puede triturar ?
Great product! However how did you break down or crush the initial stone sizes of approximately 150mm down to the 13 mm partical size that was crushed in this video?
+Richard Vincent Thanks for the question. We used a jaw crusher. You can see a video of one of our jaw crushers here: ua-cam.com/video/0bSmO9N25Yk/v-deo.html Also please check out our website for more details: www.mbmmllc.com/
@@mbmmllc chào ngài tôi quan tâm sản phẩm này của ngài , tôi muốn đặt hàng bên ngài làm thế nào để liên lạc với ngài
Magkanp pph yaan sir
Good Day ! Please Do you can inform to me where I can get one of this and his cost? Thank you very much
Hola, que precio tiene este equipo puesto puerto Santo Tomas de Castilla Guatemala..
Nostros los fabricamos en Guatemala
Can it be used to grind sea salt??
Good. Could you give me the price of Engine powed hammer mill?.
I bet you sell lots of these. Great product
Good job price this machine
How Mach the price of thet machine?
Hello
I want to know if we can grind the sand to obtain a very fine powder, and if you can make it to obtain a small quantity 50 to 100 kg.
Thank you for your comment and for watching our videos!
wondering what to do with dust throw away sell may be .????
Fine sand dust material is it usable for any thing ????
Thank you in advance
dust is worth nothing
Were i can get it
Do we have a price on this little beast?
Please email us at info@mbmmllc.com for more information on pricing and specifications.
Price and how can we buy
What is the avg cost on this machine. Same setup? Is the -50 mesh equivalent to fine flour?
Hi Bryan,
If you can send me an email at MBMMLLC@gmail.com I can send you a full price list and info sheet on all our equipment and hammer mills.
The 50 mesh minus was the smallest screen I had at the time of the test. There is a lot of material that is smaller than 50 mesh, too. Fine cooking flour is between 100 and 200 mesh for comparison.
Thanks for posting.
how much cost ?
Hola, como lo tamizan para los distinos granos ???
Our mills are designed for rocks
How much mesh it could make in hour sir...
Plz share Ur mobile number...
For pricing, please send us an email at Info@mbmmllc.com or call 360-595-4445 You can also visit our website here: mbmmllc.com/
Exelente trabajo se puede acer con material humedo y en viar los planos de esa maquina
Thank you for your comment and for watching our videos!
this is exactly what im looking for!!! same size, same power, same use. International shipping? I want to export it to Mexico. Price? thx.
For pricing, please send us an email at Info@mbmmllc.com or call 360-595-4445 You can also visit our website here: mbmmllc.com/
what capacity can that handle per hour
depending on the screen 200 kgs - 1 ton
depending on the screen 200 kgs - 1 ton
Perfect
super demo :)
bagaimana caranya agar saya dapat membeli alat tersebut?
If you can send me an email at MBMMLLC@gmail.com I can send you a full price list and info sheet on all our equipment and hammer mills.
Tienes un representante en Perú, necesito uno
Hello Cayajo-
Please send us an email at MBMMLLC@gmail.com and we can discuss the details of getting you a machine shipped to Peru. I have a past customer / importer in Ecuador who may be able to handle all the shipping for you on the machine.
Thanks,
Jason
lola necesito un equipo diesel y meza bivratoria quisiera mandarte muestras demineral para que las molieras y me informaras que equipo es el indicado
Whate is praise
اخي اين اجدك مثل هذه
For pricing and specifications please fill out our contact submission form here: www.mbmmllc.com/contact/
Mama mia perfeto
كم سعرها
Very impressive, although some other impressions are also hard to miss: That this is not an environmentally friendly method with regards to it producing dust as a final product AND as loads of fine particles in the air, and that it is not quite wise of the dudes operating the mill to not wear breathing protection..
beli alat ya di mana saya butuh 1 unit
@kai zhao saya juga butuh 1 unit.
For pricing, please send us an email at Info@mbmmllc.com or call 360-595-4445 You can also visit our website here: mbmmllc.com/
👍👍
Boleh juga
Supper
Silicosis.
dusting
Supar msand
Want to bay
Sand & Agreeget two item
Cuantobeme
❤️