با سلام همکار گرامی اگر شما IDS رو انجام داده باشی میتونی بعداز سند بلاست Bio base تمام سطح رو با اسید فسفریک اچ کنی و نیاز به اچ انتخابی نیست ضمنا شما وقتی ماده باندینگ رو کیور می کنی مانع نشست انله میشه از همه مهمتر اینکه آماده سازی انله رو نشون ندادی امیدوارم در ویدیوی بعدی این موارد رو رعایت کنی
very nice video. Thank you for sharing! After you try on the restoration, do you need to red etch the inside of the onlay restoration again? Is that red etch you used on the tooth also? Will the teflon tape add thickness to the interproximal leading to a gap? would you recommend to put a wedge?
It is more helpful if you list some reasons as to why you reached this conclusion. Bad relative to what? Bad according to which criteria? I can't know if I agree with you unless you are more specific, and perhaps you perceived something I did not. To me, this brief demonstration lacks a lot of information I would need to make a sweeping judgement, but I do see enough to at least see some room for improvement.
great point. for some reason the telio got stuck in there and it was super hard to remove. and probably too much resin cement was used and it flowed all over the place. and now i probably would have sandblasted. out of curiosity - what are some of things that you think could be improved shushant? i'm always interested in learning ;)
@@dentinaltubechannel8821 I think that it is better not to cure the adhesive layer , because you change the prosthetic field and this will leave a crack between the overlay and the preparation, i would put the adhesive , than the cement (you can use heated composite resin) and the final step would be to cure.. You can read about immediate dentin sealing. The idea is Pascal Magne's i think this will be easier to understand than my explaination.
@@drberrydds1 I respect your opinion. My protocol is first etch , bond , cement and than cure. I find this logical and enough to do my indirect restorations like that.
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
با سلام
همکار گرامی اگر شما IDS رو انجام داده باشی میتونی بعداز سند بلاست Bio base تمام سطح رو با اسید فسفریک اچ کنی و نیاز به اچ انتخابی نیست
ضمنا شما وقتی ماده باندینگ رو کیور می کنی مانع نشست انله میشه
از همه مهمتر اینکه آماده سازی انله رو نشون ندادی
امیدوارم در ویدیوی بعدی این موارد رو رعایت کنی
very nice video. Thank you for sharing!
After you try on the restoration, do you need to red etch the inside of the onlay restoration again?
Is that red etch you used on the tooth also?
Will the teflon tape add thickness to the interproximal leading to a gap? would you recommend to put a wedge?
I think the red stuff was a fit checker. to make sure all of the intaglio is in contact with prep surface.
What's up with the cracks at the base of that tooth?
looks good!
What is the temporary material used between visits?
Temp it
👍
Which material is used for bonding?
horrible la incrustacion cero anatomia
👏👏👏👏👏👏
Bad result
I agree
It is more helpful if you list some reasons as to why you reached this conclusion. Bad relative to what? Bad according to which criteria? I can't know if I agree with you unless you are more specific, and perhaps you perceived something I did not. To me, this brief demonstration lacks a lot of information I would need to make a sweeping judgement, but I do see enough to at least see some room for improvement.
What material did you use as provisional restoration?
Ivoclar's Telio CS Onlay
Dentinaltube Channel in frensh pliiiiiz
lousy work..no dexterity, improper protocol
great point. for some reason the telio got stuck in there and it was super hard to remove. and probably too much resin cement was used and it flowed all over the place. and now i probably would have sandblasted. out of curiosity - what are some of things that you think could be improved shushant? i'm always interested in learning ;)
@@dentinaltubechannel8821 I think that it is better not to cure the adhesive layer , because you change the prosthetic field and this will leave a crack between the overlay and the preparation, i would put the adhesive , than the cement (you can use heated composite resin) and the final step would be to cure.. You can read about immediate dentin sealing. The idea is Pascal Magne's i think this will be easier to understand than my explaination.
@@dentinaltubechannel8821 LOL. No he says nothing....Keep it up !
@@drberrydds1 I respect your opinion. My protocol is first etch , bond , cement and than cure. I find this logical and enough to do my indirect restorations like that.
Is better to erase this video, is not right.