Will this display work with my new electric Schwinn bike I bought from Walmart EC One cruiser bike. The one that it came with is not a screen it's just the LED one that has power in the power systems
Hi, thank you for the video, I have a question about the unit I have just installed, I set P10=2 so I can use throttle and peddle assist however peddle assist does not work (yet ?)and when I change the assist level it changes the amount of throttle I get, i.e. assist set to 1 and I don't get much power on full throttle, assist set to 5 and I get full throttle, is this correct ? I only want the peddle assist to have 5 setting not the throttle..
I have 36 volt/500 watt bike with S866 controller. Which are the P settings necessary to enable both Pedal Assist (1,2,3) along with Throttle assist? Thank You.
Hi, I have a new ebike since 2 weeks ago and would like to learn more about settings on the S866, in order to get the maximum from the bike. Can you tell me where to find a user manual for the S866? It's mounted on a HITWAY 26" 250W bike. Thank you very much!
Hi I have s866 display but every single time when I on my bike they asking me about code and the Bettrey sign is blink I can’t se how much my Bettrey is remaining
Hola amigo. ¿Has podido quitar el límite de velocidad de tu bicicleta? Yo también tengo una Hitway, y modico el código P08, lo pongo a 100, pero mi bicicleta sigue sin pasar de 25 km/h. ¿Has podido quitar el límite de velocidad? Un saludo.
Witam mam pytanie wymieniłem teraz sterownik na nowy s866 wraz z wyświetlaczem. Niby wszystko ok ale mam problem. Podczas pedałowania prędkość na wyświetlaczu pokazuje prawidłowo ale jak przestanę pedałować jadę na manetce prędkość spada do zera co może być przyczyną miał ktoś problem taki, i 2 rzecz po zaśnięciu wyświetlacza po paru minutach kasują mi się km przejechane i od zera rusza. Dziekuje
How do you show the speed on the display with a geared motor when the motor is not powered and the bike is rolling, I assume it has something to do with the white wire from the hub and the white wire to the display, do I just connect them together?
Hi. My bike have a motor on the back wheel and lights don't turn. I had a monitor key- disp before with this bike and the light was working. What should I do to be able to turn on the light on S866 ? Can I do it by setting the display or need too charge the cables?
@TomKuc-yz5ls light function works with positive terminal of battery , nagative goes directly from controller to light So if you dont have enough info for display you can directly give positive terminal of battery to the light via any switch or something without changing anything on display . If you have enough knowledge of display than there are 2 wires in display for light one is coming from controller and when you keep pressing light button that power is going to the another wire which turns of light. If you find both these wires, You just short them and light will work. Make sure the issue is not in LED light it self , before doing all this.
Thank you brother... it's a nice video... I installed a 48v 500w hub motor set on my 28" city bike... I set the p07 setting to 0001, then the km timer stopped working... I did some research and it shows the number of magnets in the motor, if it is not entered correctly. I learned that the km and distance would not be correct... Then, in the technical specifications of the engine, the magnet size was written as 27x2.3/27x3, so I entered the value 81 for testing purposes... The km meter started to work, but I did not know if it showed the speed and distance correctly... Can you help me on this issue? What should be the p07 value for my engine?
You need to check maximum by Google map or any GPS app , than try with few different input for magnets until you get actual closure to actual that you need to note down somewhere for future reference
Great video. I have the S866 display & I'm getting a 52v battery but I can't get 52v setting. I know it has it but display doesn't show it. How do I get 52v added to P03 settings?
Use 48v setting, it will undervolt a little to start, but that is better than overvolt, plus 52 is the nominal and it will be lower than that real fast under use.
52 is Nominal or full charge?? If 48v (13S)lithium ion battery is there, it have full charge voltage (upper cutoff) 54.4V And Discharge Voltage is 44V (Lower cutoff ) So your settings will be suitable for 48V if 52V is full charge voltage. (Battery options available in display are 24,36,48,60) No options in between them.
Hello, I have recently bought a BK15 Hitway and for some reason I have lost power from the motor to the battery but the digital gauge isn’t indicating there is a motor failure can you help with this please P.s my battery is fully charged too so there is no fault with this.
HELP! I have two of these displays ... and I can't get past any function after pO-8. No p2, etc. How do I access other functions? same thing on both displays so I know I'm doing something wrong.
Thanks, Great info! i have a question, my bike is 2 weeks old( ado20f) , it shuts off while riding (battery still full, 5 stripes ) . Then it wont turn on. Thought battery but tried another one from other same bike, still same problem. it happens now every time when i drive around distance of 25 km after fully charged. After charging it works again, is this maybe some kind of setting? it seems like it shuts off when it goes from battery 5 stripes to 4 stripes. Hope somebody can help solve this mystery.
It seems like battery indicator is not calibrated or faulty. If your battery is 250Kwh 25km backup is maximum it gives. But if your battery is designed for higher kilometres then there is some issue in cutoff voltage either in battery or in controller
Hi, I have just brought a bezior m3 bike, unfortunately whilst in settings the e10 code appeared, now the bike is dead. What could have caused this? Kind regards David Nicholas
Hello sir, i have a question regarding the LED turn on/off function. which wires( yellow+Black?) i need to use to connect headlamp? Also will the wires show voltage change when "long press the + button". the reason I ask is because the controller i have always has 41v (battery voltage) on the yellow and black wire, they dont change voltage. is there some setting i need to change. please help.
Maybe i can help, 41v is a 36v system, a healthy battery often sits at around 37-42v fully charged, so dont worry about that and for your headlights, they need to be connected to your controller wires, it will be a 2 pin, hopefully your kit has it and it fits, otherwise solder or join them and test the light.
Hi, I have a Hitway BK11 with an S866 display without an accelerometer. I've tried everything to change the speed in the P08 settings to 35 km/h, but the speed doesn't exceed 25 km/h. Why is that? Is it possible that the new 2023 displays have been calibrated and it's not possible to change the parameters? Or is there a way to do it?
Same problem with BK15. For sure Hitway changed something. It seems impossible with the display. Usually with a lot of bikes you just open the controller and disconnect 2 cables. I didn't check because recently I saw several videos about people who did it with a Hitway and it didn't work. Could you please tell here if you found?
@@baroul59 I did it, you need to pull both brake levers for 10 seconds and turn on the display while keeping the brake levers pulled. After 10 seconds, access the P8 settings and change it to 100; my bike reaches a maximum speed of 32 km/h.
@@matteo3676After 10 seconds, we release the brakes and enter P8 or continue to hold it. Do we count these 10 seconds from turning on the display with the brakes pressed, or from pressing the brakes and turning on the display? I have Hitway BK27.
Szia, csatolnad légyszives az összes menu pontot a magyarázatot a 21 menüről, vagy a táblázatot róla? Fotóval is jo akár. Ide nekem válaszként. Köszönöm Hi, could you please attach all the menu points, the explanation of the 21 menu, or the table about it? Even with a photo. Here as an answer for me. Thanks
i dont have any paddle assist sensor but if i use plus button itll increase the speed???!!! why is that? and if you let the vehicle to get some speed like 30km/h then if i let go the throttle the scooter suddenly jerks backward ... !!! why its happening Mr?
hello my friend, my mileage is up to 8 kilometers on the display. while the bike goes faster...what would I do? Do you happen to have an answer to my question?
hi, Even if I press the + and - buttons, "- - - -" appears and I cannot proceed to the settings. Please tell me the password. There was a problem with the display, so I replaced it with a new s866 and couldn't proceed. In the previous s866, you could proceed to the settings. The bike is ado a26s
@@InfiniteLaboratory , I am trying to experiment with Hero Lectro. 36 volts, 250 watt motor and controller. And the button remote has no display, with just 4 leds and three buttons. But the button remote has the waterproof green plug. So I thought about experimenting with the s886. So, thats what I am asking, You Have it, but where? Which website? Which number?
hello, when i press both the + and - button, i dont see the mode settings.. i only the letter C with 0000..what can i do to enter the settings..pls help
I have this display. It doesn't show me all the parameters. It only shows a few of them. Can you tell me how make all the parameters available, Thank you 👍
@@nikelliott9564 hey. I asked and such. My reply is it's the controller. It's simply not interested in being anything different than what it is. It seems to be that to make this cool bike do more. Is a no go. I cracked my brain. It's simply the controller is a block. It's a great bike. And ya . It's kinda limited without a controller swap
Read other comments, 99% people are finding it more useful than the manuals provided by company it self. I am sorry for those 1% people who don't understand my language or my way of explanation. Sincere apologies.
Read other comments, 99% people are finding it more useful than the manuals provided by company it self. I am sorry for those 1% people who don't understand my language or my way of explanation. Sincere apologies.
If there is a speed signal Comming out from motor and controller, but it is not being used in your LED display, then changing to an LCD display will definitely work.
@@InfiniteLaboratory I replaced the S810 display with the S860. It turned on and I was able to change the parameters but when I used the throttle, the wheel moved half way around then stopped.
Thanx a lot my friend best info
Most welcome
Made a lot more sense than trying to decipher the Manual that some manufacturers send with this display 🙂
Thanks for appreciating our efforts
Will this display work with my new electric Schwinn bike I bought from Walmart EC One cruiser bike. The one that it came with is not a screen it's just the LED one that has power in the power systems
Hi, thank you for the video, I have a question about the unit I have just installed, I set P10=2 so I can use throttle and peddle assist however peddle assist does not work (yet ?)and when I change the assist level it changes the amount of throttle I get, i.e. assist set to 1 and I don't get much power on full throttle, assist set to 5 and I get full throttle, is this correct ? I only want the peddle assist to have 5 setting not the throttle..
great tutorial! thank you
Our Pleasure
Hi, should the peddle assist level (1-5)setting also change the throttle power ?
Thanks for your explanation sir.
I have 36 volt/500 watt bike with S866 controller. Which are the P settings necessary to enable both Pedal Assist (1,2,3) along with Throttle assist?
Thank You.
P10 and you indicate:0002 (if you wrote 0000 you have to push only, if you wrote 0001 booster only)
what's p19 do thanks@@baroul59
When you start the display, you can shortly see 100% next to the battery. Is there anyway to enable this battery percentage view??
No sir
Hi, I have a new ebike since 2 weeks ago and would like to learn more about settings on the S866, in order to get the maximum from the bike. Can you tell me where to find a user manual for the S866? It's mounted on a HITWAY 26" 250W bike. Thank you very much!
Hi I have s866 display but every single time when I on my bike they asking me about code and the Bettrey sign is blink I can’t se how much my Bettrey is remaining
Hola amigo.
¿Has podido quitar el límite de velocidad de tu bicicleta? Yo también tengo una Hitway, y modico el código P08, lo pongo a 100, pero mi bicicleta sigue sin pasar de 25 km/h.
¿Has podido quitar el límite de velocidad? Un saludo.
Mail us your inquiry on infinitelaboratory@gmail.com
Please which controller do you recommend for Himo Z20. I tried the S866 but it does not seam to work. Thanks
As per protocol it works
Thanks will this display work on any 48v e bike ?
yes till 60v
Hello, have you any information from s869 display? i cant find any, my bike comes with that display
Hi. When I hold down the minus button it goes into P mode. And the wheel moves on its own. But only to 6km/h. Is there a way to increase it
P04 on 10 isn't 10 seconds, it's 10 minutes. Just looking out.
Witam mam pytanie wymieniłem teraz sterownik na nowy s866 wraz z wyświetlaczem. Niby wszystko ok ale mam problem. Podczas pedałowania prędkość na wyświetlaczu pokazuje prawidłowo ale jak przestanę pedałować jadę na manetce prędkość spada do zera co może być przyczyną miał ktoś problem taki, i 2 rzecz po zaśnięciu wyświetlacza po paru minutach kasują mi się km przejechane i od zera rusza. Dziekuje
How do you show the speed on the display with a geared motor when the motor is not powered and the bike is rolling, I assume it has something to do with the white wire from the hub and the white wire to the display, do I just connect them together?
Yes, You can try that way
Hi. My bike have a motor on the back wheel and lights don't turn.
I had a monitor key- disp before with this bike and the light was working. What should I do to be able to turn on the light on S866 ? Can I do it by setting the display or need too charge the cables?
@TomKuc-yz5ls light function works with positive terminal of battery , nagative goes directly from controller to light
So if you dont have enough info for display you can directly give positive terminal of battery to the light via any switch or something without changing anything on display .
If you have enough knowledge of display than there are 2 wires in display for light one is coming from controller and when you keep pressing light button that power is going to the another wire which turns of light. If you find both these wires,
You just short them and light will work.
Make sure the issue is not in LED light it self , before doing all this.
Thank you brother... it's a nice video... I installed a 48v 500w hub motor set on my 28" city bike... I set the p07 setting to 0001, then the km timer stopped working... I did some research and it shows the number of magnets in the motor, if it is not entered correctly. I learned that the km and distance would not be correct... Then, in the technical specifications of the engine, the magnet size was written as 27x2.3/27x3, so I entered the value 81 for testing purposes... The km meter started to work, but I did not know if it showed the speed and distance correctly... Can you help me on this issue? What should be the p07 value for my engine?
You need to check maximum by Google map or any GPS app , than try with few different input for magnets until you get actual closure to actual that you need to note down somewhere for future reference
Great video. I have the S866 display & I'm getting a 52v battery but I can't get 52v setting. I know it has it but display doesn't show it. How do I get 52v added to P03 settings?
Use 48v setting, it will undervolt a little to start, but that is better than overvolt, plus 52 is the nominal and it will be lower than that real fast under use.
52 is Nominal or full charge??
If 48v (13S)lithium ion battery is there, it have full charge voltage (upper cutoff) 54.4V
And Discharge Voltage is 44V (Lower cutoff )
So your settings will be suitable for 48V if 52V is full charge voltage.
(Battery options available in display are 24,36,48,60)
No options in between them.
❤ thank you bro
Welcome 😊
how do you get into "communication state" to ge tot p09?
Hello, I have recently bought a BK15 Hitway and for some reason I have lost power from the motor to the battery but the digital gauge isn’t indicating there is a motor failure can you help with this please
P.s my battery is fully charged too so there is no fault with this.
It may possible there is some other issue but the program is not able to find it.
can I convert an ebike with a 810 controller to an S866?
Thanks for sharing this, PDF please
Hi thanks for this video
My bike pass not working no error show(display settings p10 set pass+throttle)
Some issue in magnet plate or sensor
HELP!
I have two of these displays ... and I can't get past any function after pO-8.
No p2, etc.
How do I access other functions?
same thing on both displays so I know I'm doing something wrong.
It has the s866 display unit and its 48v regards David Nicholas
Why do I only have access to 3 perimeters on my display. I have a 500w 48v fat tire ebike
THANK U.
You're welcome!
Thanks, Great info! i have a question, my bike is 2 weeks old( ado20f) , it shuts off while riding (battery still full, 5 stripes ) . Then it wont turn on. Thought battery but tried another one from other same bike, still same problem. it happens now every time when i drive around distance of 25 km after fully charged. After charging it works again, is this maybe some kind of setting? it seems like it shuts off when it goes from battery 5 stripes to 4 stripes. Hope somebody can help solve this mystery.
It seems like battery indicator is not calibrated or faulty. If your battery is 250Kwh 25km backup is maximum it gives.
But if your battery is designed for higher kilometres then there is some issue in cutoff voltage either in battery or in controller
My battery level doesn't shows correct in speedometer what settings or parameters should i change sir.
Hi, I have just brought a bezior m3 bike, unfortunately whilst in settings the e10 code appeared, now the bike is dead. What could have caused this? Kind regards David Nicholas
me too 🤮
E10 is communication error of display and controller, may be because of wrong connection or loose connection, or failure in any of them.
Hello sir, i have a question regarding the LED turn on/off function. which wires( yellow+Black?) i need to use to connect headlamp? Also will the wires show voltage change when "long press the + button". the reason I ask is because the controller i have always has 41v (battery voltage) on the yellow and black wire, they dont change voltage. is there some setting i need to change. please help.
Maybe i can help, 41v is a 36v system, a healthy battery often sits at around 37-42v fully charged, so dont worry about that and for your headlights, they need to be connected to your controller wires, it will be a 2 pin, hopefully your kit has it and it fits, otherwise solder or join them and test the light.
Hi, I have a Hitway BK11 with an S866 display without an accelerometer. I've tried everything to change the speed in the P08 settings to 35 km/h, but the speed doesn't exceed 25 km/h. Why is that? Is it possible that the new 2023 displays have been calibrated and it's not possible to change the parameters? Or is there a way to do it?
you tried setting P08 to 100? and the wheel size, magnet qty and gear:v input correct?
Same problem with BK15. For sure Hitway changed something. It seems impossible with the display. Usually with a lot of bikes you just open the controller and disconnect 2 cables. I didn't check because recently I saw several videos about people who did it with a Hitway and it didn't work. Could you please tell here if you found?
@@baroul59 I did it, you need to pull both brake levers for 10 seconds and turn on the display while keeping the brake levers pulled. After 10 seconds, access the P8 settings and change it to 100; my bike reaches a maximum speed of 32 km/h.
Perfect thanks! I saw the short vid about it. Are you sure you can delete it, I mean no problem to go back to 25km/h in case of control?
@@matteo3676
@@matteo3676After 10 seconds, we release the brakes and enter P8 or continue to hold it. Do we count these 10 seconds from turning on the display with the brakes pressed, or from pressing the brakes and turning on the display? I have Hitway BK27.
Szia, csatolnad légyszives az összes menu pontot a magyarázatot a 21 menüről, vagy a táblázatot róla? Fotóval is jo akár. Ide nekem válaszként. Köszönöm
Hi, could you please attach all the menu points, the explanation of the 21 menu, or the table about it? Even with a photo. Here as an answer for me. Thanks
You can mail your inquiry on infinitelaboratory@gmail.com
i dont have any paddle assist sensor but if i use plus button itll increase the speed???!!! why is that? and if you let the vehicle to get some speed like 30km/h then if i let go the throttle the scooter suddenly jerks backward ... !!! why its happening Mr?
It may have some other issues related to controller
Hello , how do i know how many magnets i am afraid i set messed with the wrong one , will it break now?
Magnets on sensor can be checked from plate.
hello, do you know how to change the speed limit with s869 lcd display?
Yes.
You can mail your questions to infinitelaboratory@gmail.com
@@InfiniteLaboratory have done it , waiting for answer :)
Sorry how it's possible show percentages battery? Thanks.
No sir
where is the link for the manual thanks
Van you help please.me display go to 8 and it's the same as yours nr 9 .10.11 ..........i Cant come in that program.pleace help
My paddle assist stopes late after paddling is stopped and starts a bit late when starting to paddle is there an adjustment in the settings
In other words even when paddling is stopped the motor has power take a bit longer for the motor to stop working
May be due to some issues in controller or lagging of signals
hello my friend, my mileage is up to 8 kilometers on the display. while the bike goes faster...what would I do? Do you happen to have an answer to my question?
You may have entered wrong wheel diameter
Hello, how to change gear speeds at S866? For example 1-10km 2-15km 3-20km 4-30km 5- full speed? Any tips please?
On PAS mode, or on throttle mode???
@@InfiniteLaboratory both
can u also tell where to get this manuel please S866 for hitway bike Name BK8M , i did write the company but waiting thank you
hi,
Even if I press the + and - buttons, "- - - -" appears and I cannot proceed to the settings. Please tell me the password. There was a problem with the display, so I replaced it with a new s866 and couldn't proceed. In the previous s866, you could proceed to the settings. The bike is ado a26s
Infinite where are you please guide me quick
Do you have this controller only? Can you give me link? Cannot find your shop anywhere.
We have this controller and display both items
@@InfiniteLaboratory , I am trying to experiment with Hero Lectro. 36 volts, 250 watt motor and controller. And the button remote has no display, with just 4 leds and three buttons. But the button remote has the waterproof green plug. So I thought about experimenting with the s886.
So, thats what I am asking, You Have it, but where? Which website? Which number?
I have a metakoo cybertrack 100 and cant get my bike to run the motor
You need to contact local repair shop first. If they can't help you can try yourself
How to set a passcode to restrict access to S866 menu options?
hello, when i press both the + and - button, i dont see the mode settings.. i only the letter C with 0000..what can i do to enter the settings..pls help
C 0000 IS ALSO A SETTING MODE.
You need to check specifications sheet and parameter settings manual
I have this display.
It doesn't show me all the parameters.
It only shows a few of them.
Can you tell me how make all the parameters available,
Thank you 👍
Did you ever find out how to unlock all off the p1-20 settings ? I believe mines the same.as yours and skips several settings
@@nikelliott9564 hey. I asked and such.
My reply is it's the controller. It's simply not interested in being anything different than what it is.
It seems to be that to make this cool bike do more. Is a no go.
I cracked my brain.
It's simply the controller is a block.
It's a great bike. And ya . It's kinda limited without a controller swap
How to reset p3c and s866 display to clear fault
Hai
Where is pdf of this specification...
Pls share pdf file
Plz solution error -e10
I have hit way bk9 cycle brother display show error brother how to solve any one know pls contact me
What error?
Hello please solve my issue anyone
What issues sir?
He reads from the paper, but he doesn't explain anything. I still have no idea what most of the settings are.
Sorry if you find it difficult to understand.
Will explain more details in next videos
Read other comments, 99% people are finding it more useful than the manuals provided by company it self.
I am sorry for those 1% people who don't understand my language or my way of explanation.
Sincere apologies.
This is giving me a headache ... delete video and set yourself up so your not having such a hard time pressing buttons and searching for shit 🤣😖
Read other comments, 99% people are finding it more useful than the manuals provided by company it self.
I am sorry for those 1% people who don't understand my language or my way of explanation.
Sincere apologies.
can I convert an ebike with an 810 controller to an S866?
If there is a speed signal Comming out from motor and controller, but it is not being used in your LED display, then changing to an LCD display will definitely work.
@@InfiniteLaboratory I replaced the S810 display with the S860. It turned on and I was able to change the parameters but when I used the throttle, the wheel moved half way around then stopped.
@@InfiniteLaboratory I changed the S810 controller on the Gotrax Endura 350 watt motor with the S860
@@caprice240k may be some parameters were wrong in that case