Follow these simple 1,134 steps to replace your fuser! Half the time I couldn't tell what I I was looking at in the video. I finally realized that the upper right was the orientation of the printer, but I had many things that just didn't match so it was still a pain. Absolutely the WORST printer to ever work on! I've had to recommend to all my clients to switch printers after MANY MANY complaints about the cost to service it. Whoever thought this design was OK, and the idiot who approved it should immediately be demoted to servicing this printer a minimum wage! Even worse when you fire it back up and you get some generic "Internal Communication Error" and have no idea which of the 150 parts you messed with that it could be! The one I just finished I'm pretty sure the cable to the scanner is messed up, I didn't get the hinge in all the way (while I give you props for the top to tape down the scanner, there was no mention about getting that tab to fit in there just right) and when I went to look at it, it sprung open and flew off the back and was hanging by the cables. Way to ruin a $900 printer!
Most manufacturers have it so fuser just pulls out without having to strip machines down. Why has hp made it so awkward to change a consumable part? These bits do need replacing from time to time.
Just went through this... pure pain and suffering, just to remove a 0.5x0.5 inch piece of paper that got stuck and jammed printer whenever printing on two sides...
Hola Mónica, ¡gracias por ponerse en contacto con el soporte global de redes sociales de HP! Entiendo que necesitas comprar el rodillo dúplex. Haré todo lo posible para ayudarte. Utilice el navegador de piezas HP para identificar la pieza: partsurfer.hp.com/search.aspx Y pídalo a través de la tienda de piezas de HP: bit.ly/3nKMYrs Binu_HP Soporte técnico de redes sociales
TENGO UNA IMPRESORA IGUAL, PERO A LA HORA DE IMPRIMIR, DE UN LADO ME MARCA MAS TENUE LAS IMPRESIONES QUE DEL OTRO, AUNQ MIS CARTUCHOS ESTEN LLENOS, ALGUIEN ME PODRA AYUDAR CON ESTA IMPRESORA MFP M477 fnw............ ayudaaaaaaaaaaaaaaaaaaaaaaaaaa
+GENE SIMMONS thanks for reaching out. The support here is in English only. If you could post back in English, I'd be glad to help? If in case you need support in your language, I'd recommend you refer our localized channel link: ua-cam.com/users/HPSupport
@@HPSupport I HAVE THE SAME PRINTER, BUT AT TIME TO PRINT, ON ONE SIDE IT MARKS ME MORE I HAVE THE PRINTS THAN ON THE OTHER, EVEN MY CARTRIDGES ARE FULL, SOMEONE WILL BE ABLE TO HELP ME WITH THIS PRINTER MFP M477 fnw ......... ... helpaaaaaaaaaaaaaaaaaaaaaaaa
Hi Aureure, thanks for contacting HP Global Social Media Support! I am here to help! What seems to be the issue? Are you facing any technical issues with your HP printer? May I know the printer you are using? Let me know! Binu_HP Social Media Tech Support
Follow these simple 1,134 steps to replace your fuser!
Half the time I couldn't tell what I I was looking at in the video. I finally realized that the upper right was the orientation of the printer, but I had many things that just didn't match so it was still a pain.
Absolutely the WORST printer to ever work on! I've had to recommend to all my clients to switch printers after MANY MANY complaints about the cost to service it. Whoever thought this design was OK, and the idiot who approved it should immediately be demoted to servicing this printer a minimum wage!
Even worse when you fire it back up and you get some generic "Internal Communication Error" and have no idea which of the 150 parts you messed with that it could be! The one I just finished I'm pretty sure the cable to the scanner is messed up, I didn't get the hinge in all the way (while I give you props for the top to tape down the scanner, there was no mention about getting that tab to fit in there just right) and when I went to look at it, it sprung open and flew off the back and was hanging by the cables. Way to ruin a $900 printer!
Most manufacturers have it so fuser just pulls out without having to strip machines down. Why has hp made it so awkward to change a consumable part? These bits do need replacing from time to time.
Just went through this... pure pain and suffering, just to remove a 0.5x0.5 inch piece of paper that got stuck and jammed printer whenever printing on two sides...
alguien tendrá el numero de parte del rodillo del duplex
Hola Mónica, ¡gracias por ponerse en contacto con el soporte global de redes sociales de HP!
Entiendo que necesitas comprar el rodillo dúplex.
Haré todo lo posible para ayudarte.
Utilice el navegador de piezas HP para identificar la pieza: partsurfer.hp.com/search.aspx
Y pídalo a través de la tienda de piezas de HP: bit.ly/3nKMYrs
Binu_HP Soporte técnico de redes sociales
TENGO UNA IMPRESORA IGUAL, PERO A LA HORA DE IMPRIMIR, DE UN LADO ME MARCA MAS TENUE LAS IMPRESIONES QUE DEL OTRO, AUNQ MIS CARTUCHOS ESTEN LLENOS, ALGUIEN ME PODRA AYUDAR CON ESTA IMPRESORA MFP M477 fnw............
ayudaaaaaaaaaaaaaaaaaaaaaaaaaa
+GENE SIMMONS thanks for reaching out. The support here is in English only. If you could post back in English, I'd be glad to help? If in case you need support in your language, I'd recommend you refer our localized channel link: ua-cam.com/users/HPSupport
@@HPSupport I HAVE THE SAME PRINTER, BUT AT TIME TO PRINT, ON ONE SIDE IT MARKS ME MORE I HAVE THE PRINTS THAN ON THE OTHER, EVEN MY CARTRIDGES ARE FULL, SOMEONE WILL BE ABLE TO HELP ME WITH THIS PRINTER MFP M477 fnw ......... ...
helpaaaaaaaaaaaaaaaaaaaaaaaa
your fuser is a mess....
Hi Aureure, thanks for contacting HP Global Social Media Support!
I am here to help!
What seems to be the issue? Are you facing any technical issues with your HP printer?
May I know the printer you are using?
Let me know!
Binu_HP Social Media Tech Support