Please note that the UART for DJI RC2 depends on the FC BETAFPV has delivered. The older ones use UART6, but the newer ones are using UART5 instead. I have both, so I definitely know...
Oh God, Thank You so much, you save my time , I've been trying to connect dji rc2 for past 2 days and it connects but it won't response in the receiver in betaflight app
I have tried this several times, step-by-step, following along and it does not work. My controller is still not successfully sending commands to my drone. I can't even get it to show response in Betaflight. I've updated everything to the latest firmware, activated my O3 air unit, and the pairing process seems to work at face value. The controller connects and I have a video feed in my goggles, but nothing seems to happen when I attempt to send controller inputs. Any ideas?
This one works for me: DJI Googles 2 Settings->Control->Protocol - Standard Betaflight - Ports - UART5 Betaflight - Receiver - SBUS Betaflight - Modes ARM - AUX4
Thanks for a wonderful video. The only confusing thing is that mine would only connect with Uart 5. everything functions except after I arm it the prop don’t spin unless yaw. I spent hours trying to correct it and will switch to a different radio but is disappointing because I bought the 03 unit to use with my Dji p2rc
I picked SBUS as this video says, and I believe I did everything - my remote can start recording videos but I can't fly, as it says it's in low power mode in my Goggles 2. Any idea? Sorry to bother you but I've been trying this for a few months by now and I'm getting close little by little, I think this may be the last question I have for Pavo Pico... After SBUS the stick movements don't show up at the "Receiver" section of my Betaflight either. Thank you in advance, your video is great.
Hello so i bought a Cinelog35 v2 and i can't get the dji fpv remote to connect, i bought the ELRS 2.4 with GPS, I got the Jumper Tlite ELRS and wasn't able to get that to pair with it, so I got the FPV dji drone remote and no I still can't seem to get it to pair with it. Any thoughts?
when I go to the receiver section I only see USB VPC, UART 1 and UART2, I have correctly connected the DJI Remote 2 to the drone and also the DJI Goggle V2 but the DJI Remote 2 is not detected by betaflight
Hi, thx for your great video! I got one question, how do you get the telemetry data into the OSD for the Googles V2 with the Pavo Pico 2-3S FC? Thank you😊
Hard to tell, but if you have already DJI RC2, you may use this one. If you have to buy a new one, Radiomaster with ELRS is a cheap but good choice. Others prefer TBS controller, much more expensive. Decide BEFORE buying the drone!
Hello, I have a pavo 20 and a picó, with a pocket elrs radiomaster, and even though the drone and the radio are linked, it does not give responses either in betaflight or in the drone, it does not arm, it does nothing, however it shows telemetry connection with the drone :(
Hey I have axisfliying o3 unit system. There is tbs crossfire receiver. I remove it . But Betaflight can't see remote controller in receiver screen ? What am I miss ? fc card is Axisflying Argus F7. am I choice wrong uarn ?
@@dailydronejourneyuart @@dailydronejourney. Uart1 open reboot close after control receiver. After other all uart tried. Not stick move in the receiver page
my lite 3pro radio controler doesnt come with Express ERLS, do i have to update or something? please new drone just arrived pavo pico and beta lite3 pro
I am connected with DJI controller 2. How do I arm. I have not been able to get my controller to control the drone in Betaflight. As you can see I am new at this. What am I missing.
@@MrTechcat which button modes ? I have tried several and they are not working ... :S when I have selected one of them always the mode turns in red color and it is labed: DISARMED. I do not know if that is good or bad configurantion.
BetaFPV Pavo Pico Whoop - bit.ly/3KSYhcW
BetaFPV LiteRadio 3 Pro - bit.ly/3S0H82b
Please note that the UART for DJI RC2 depends on the FC BETAFPV has delivered. The older ones use UART6, but the newer ones are using UART5 instead. I have both, so I definitely know...
You save my day! 🙏🏻
How can you tell? Just trial and error or is there a way to visually check?
Oh God, Thank You so much, you save my time , I've been trying to connect dji rc2 for past 2 days and it connects but it won't response in the receiver in betaflight app
@@SunriseWaterMedia The PCB from the second batch (UART5) is labeled F4 2-3S 20A AIO instead of F4 1-2S 12A AIO (for UART6)
Thanks!!😅
I just got the Pavo Pico! Got motivated to use it watching your video!
The only thing missing is setting up Modes in Betaflight because the defaults wont work with RC2, but otherwise pretty helpful!
Pavo20 just delivered today can’t wait to fly it vs the Avata!
I have tried this several times, step-by-step, following along and it does not work. My controller is still not successfully sending commands to my drone. I can't even get it to show response in Betaflight. I've updated everything to the latest firmware, activated my O3 air unit, and the pairing process seems to work at face value. The controller connects and I have a video feed in my goggles, but nothing seems to happen when I attempt to send controller inputs. Any ideas?
this is my current problem. Hopefully there's a fix because I am going nuts right now LOL. Pavo 20 is connected with my RC2 and Goggles V2
@@citronbullsame problem. Did U solved this?
Same
The same here. I am on 4.4 firmware. Should I try 4.5 or lower version?
This one works for me:
DJI Googles 2
Settings->Control->Protocol - Standard
Betaflight - Ports - UART5
Betaflight - Receiver - SBUS
Betaflight - Modes ARM - AUX4
This video answers my question! thank you
Dude. You are the man.
THANK YOU VERY MUCHHHH!! if you have a pavo20, use UART5 instead of 6 in the Ports under the RX serial. That saved me!!
how do you know ?
how do you know UART6 is using for DJI O3 in 2:26 minute ?
Thanks for a wonderful video. The only confusing thing is that mine would only connect with Uart 5. everything functions except after I arm it the prop don’t spin unless yaw. I spent hours trying to correct it and will switch to a different radio but is disappointing because I bought the 03 unit to use with my Dji p2rc
BROTHER I CAN DO THE SAME IF MY DRONE IS WITH TBS, I WANT TO CONNECT IT WITH THE DJI 2 CONTROLLER, I HAVE UNIT 03 INCLUDED HELP
I picked SBUS as this video says, and I believe I did everything - my remote can start recording videos but I can't fly, as it says it's in low power mode in my Goggles 2. Any idea? Sorry to bother you but I've been trying this for a few months by now and I'm getting close little by little, I think this may be the last question I have for Pavo Pico... After SBUS the stick movements don't show up at the "Receiver" section of my Betaflight either. Thank you in advance, your video is great.
Hello so i bought a Cinelog35 v2 and i can't get the dji fpv remote to connect, i bought the ELRS 2.4 with GPS, I got the Jumper Tlite ELRS and wasn't able to get that to pair with it, so I got the FPV dji drone remote and no I still can't seem to get it to pair with it. Any thoughts?
Did you ever get this situated?
when I go to the receiver section I only see USB VPC, UART 1 and UART2, I have correctly connected the DJI Remote 2 to the drone and also the DJI Goggle V2 but the DJI Remote 2 is not detected by betaflight
do we must, to desolder elrs in FC?
when configuring the dji remote does it have to be on, plugged in....? because i'm unable to get it functional at all
Hi, thx for your great video! I got one question, how do you get the telemetry data into the OSD for the Googles V2 with the Pavo Pico 2-3S FC? Thank you😊
Bro quick question, which versión of all I have to buy to able to bind it to dji controller? I can see pnp, ielr2.4 or tbs but not sure 😢
both pnp and elrs will work
Hello! Please tell me, if I buy the version with TBS, will I not be able to connect my DJI RC2?
It must be so awesome to have good eyesight, I would never see the screen on the beta fpv transmitter
But are you still able to send out the drone without good eyesight ?
Do you have to change back and forth from SBUS and CROSSFIRE when you change radios?
Yes, and don't forget to change UART port too.
Thank you. @@MrTechcat
Can i use dji radio to link the pavo pico 25 v2 this way? Thanks
Which remote control is better?
I like LiteRadio 3 Pro. Nice gimbals, buttons and more features.
Hard to tell, but if you have already DJI RC2, you may use this one. If you have to buy a new one, Radiomaster with ELRS is a cheap but good choice. Others prefer TBS controller, much more expensive. Decide BEFORE buying the drone!
Sorry, what's the difference between the ELRS and the TBS in the Betafpv website?
For other quads how can we determine which uart is for the dji remote controller 2? Thank you
same question.. do you have find the answer ?
Hello, I have a pavo 20 and a picó, with a pocket elrs radiomaster, and even though the drone and the radio are linked, it does not give responses either in betaflight or in the drone, it does not arm, it does nothing, however it shows telemetry connection with the drone :(
Pavo is not the same as Pico. I got my new Pico 20 works exactly the same and was able to switch to the DJI radio. :)
Does the dji controller + O3 combination not cause problems with Rxloss?? I've been crashing with RXLOSS errors, please help if you know how.
You need to unlock your DJI goggles, if you are flying in EU. As stock range totally sucks. I have videos how to unlock on my channel.
Before switching from ELRS to DJI RC2, did you deactivate ELRS as indicated by betafpv? I tried that and I still have the same problem.
same question.. do you have find the answer ?
hi, can someone tells me , how to bind literadio 3 pro with pavo pico.
nice video. make me connect my nazgul.. Thanks.
Hey I have axisfliying o3 unit system. There is tbs crossfire receiver. I remove it . But Betaflight can't see remote controller in receiver screen ? What am I miss ? fc card is Axisflying Argus F7. am I choice wrong uarn ?
do you have try any UART Port ?
@@dailydronejourneyuart @@dailydronejourney. Uart1 open reboot close after control receiver. After other all uart tried. Not stick move in the receiver page
@@mebzorf hi, i did.. and successfull
my lite 3pro radio controler doesnt come with Express ERLS, do i have to update or something? please new drone just arrived pavo pico and beta lite3 pro
It comes out of the box, if you bought ExpressLRS version..
and if you bought CC2500 version, that does not support ExpressLRS.
Hello!
what glasses do you use?
hello, With the dji RC2 and goggles integra withc rx should i get the expressLRS2 or TBS
elrs2
@@MrTechcatinteresting, but why exactly?
Are you able to fly in DJI's 'normal, sport, manual' mode on the Pavo Pico?
Just manual and auto level, as the drone does not have GPS.
You can add a GPS module to the PICO, so did I, but this does nothing to the fly modes...
I am connected with DJI controller 2. How do I arm. I have not been able to get my controller to control the drone in Betaflight. As you can see I am new at this. What am I missing.
you need to set your remote switches in Modes tab too.
@@MrTechcathey tech cat. Can you elaborate on how you set modes
My motors will not arm with the DJI remote 2?
you need to change button modes
@@MrTechcat which button modes ? I have tried several and they are not working ... :S when I have selected one of them always the mode turns in red color and it is labed: DISARMED. I do not know if that is good or bad configurantion.
Can I use dji controller remote 2 on my cetus x??
nope, only drones with DJI o3
Ok ok ty bro
why do pilots choose ELRS and TBS over DJI O3 for range, the VTX of O3 is the king of distance , in HD
Which remote control is better?