It's nice to see a precise sled without the usual base plate supporting the workpiece. For small table saws, every mm of usable blade depth is valuable!
What an awesome job and a beautiful sled. The only thing I could say is (being a retired woodworker and professional table saw operator for over 40 years ) when cutting wood on a table saw use constant motion while pushing the wood piece past the saw blade. Been telling this to trainees for years. I noticed you scar the wood as you stop and it can be plainly seen on the wood pieces you cut. I only say this to make you a better woodworker and show the public an even better you. I intend to make one of these designs when I open my shop. It's a really good design. Thanks for sharing.
Thank you for sharing this wonderful idea and excellent video. I admire your workmanship and presentation. I hope that you and your loved ones keep well in this current health crisis. Best wishes from Australia.
Um projeto muito bem elaborado e feito com carinho e muita precisão. Uma ideia a ser adotada por quem padece com o excesso de peso de uma guia para realizar cortes em sua mesa de serra circular. Só reluto no emprego daquelas duas guias paralelas, de pinnus, pois sendo uma madeira macia, não demorará a sofrer desgaste dentro dos canais da mesa que o acomodam, caso o ritmo de trabalho seja intenso. Quanto ao resto, só elogios. Parabéns!
Just a suggestion, wouldn't it be easier to glue up the two rabbeted boards then cut the bolt slot? I liked the method how you squared the unit to the blade. Excellent quality workmanship and attention to detail. The pointer is a nice touch. Thanks for sharing. Looking forward to your next video.
You can also use a t-slot router bit which will cut the channel in one shot, so you don't have to perform multiple cuts. Those have saved a lot of time for me.
Yes, if you have a router table and T-slot bit, not everyone does. What he shows you here is basically is how to build this without a router table so in essence he’s showing people two different ways simultaneously. (Assuming, like you, knowledge of what a T-slot bit does) I, too, admire is attention to detail and creativity. I only wish I had his patience instead of my usual practice of going a hundred miles an hour and trying to build everything in one day!
Excellent sled, video and work. I'm confused about one thing, when you attached the rule tape to the top, why did you go with this positioning vice zeroing it at the blade?
Saudações do Brasil amigo. Seu trabalho é lindo, limpo e impecável . Conquistou-me como inscrito e seguidor. Vou tentar seguir seu exemplo. Muita paz, saúde e felicidade. Obrigado.
It's funny I should see this today. I have been trying to come up in my mind a way to set the fence angle accurately without all the trial and error. My idea was to cut a 1" board on the right side using the miter slot and bouncing the square off it, LOL. The difference is that I plan to make a split sled where the left side or right side can be used independently or together as one sled. I see I saw this video in the past, so maybe that's where my mind picked it up. I have a lot of creative ideas, but I mostly get them from parts of many different sources over the years. I just sort them out to make one good idea from them. Thanks for the video. I needed this one today.
Espero que se entienda lo que quiero decir...usted y muchos de ustedes hermanos del otro lado del mundo oriental poseen un nivel de alto desarrollo de los ingeniería aplicada, con un grado de simpleza y practicidad, una visión más amplia y un nivel de detalles sorprendente que no logro ver por este otro lado del mundo occidental. Siempre encuentro estas características al ver videos relacionados al bricolaje y creo que lo he comentado con otras personas y muchos dicen que son una raza superior y usted confirma lo que le comento. Si existiera la posibilidad de volver a nacer... desearía estar desde el otro lado para confirmar mi observación. Muy agradecido por su trabajo y experiencia saludos cordiales 🖐️ desde Chile 🇨🇱
Cómo puede ser?? Todos sus trabajos ,por muy pequeños o grandes que sean tienen un magnífico resultado final , gracias por compartir tanta creatividad y conocimientos , un saludo cordial y por supuesto un gran like desde Narón , Galicia (España) 😜🤓🤣
Increible trabajo, valoro su creatividad, al principio no suponía utilidad y al final vi que es tremendamente útil, felicidades, su like y desde luego me suscribo, saludos desde el Puerto de Veracruz, México.
Наверное, было-бы более технологично, если склеить две массивные детали и уже затем осуществить пропил зазора под болт. 1:15 А сама идея мне очень понравилась. Спасибо.
Al levantar las piezas recién pegadas se pueden desalinear. Mejor dejarlas sobre la mesa y usar morsetas. O poner clavitos provisorios. O al menos espolvorear sal en la unión.
Pretty nice work, but there are much easier ways to accomplish the same thing. Waaa...y too many little parts. Really hard to keep from making an unacceptable cumulative error.
WHAT AN AWESOME BUILD!! Something else I've been meaning to make for a while but, I'm glad I waited...you have given me some great ideas. I really like the RED LINE on the clear acrylic...I may use my own blood for that...
Sorry about my belated reply. I fell in love with my job. Very busy with thinking over and over about next videos and preparing parts which I'm not accustomed to. There are so many strange hardware, bits and parts. Those are what I break through. Thanks buddy.
No worries about the slower replies. As your channel grows, you'll have less time to reply to these things and maybe eventually not have time to reply to any of them at all. I can certainly see that you are very diligent to reply as much as you can and you have not missed one yet. Pretty amazing actually. I'm sure it will make your subscribers very loyal to you and your content.
![drill press table with a fence & 2 vices in 1 / sliding dovetail rail [woodworking]](http://i.ytimg.com/vi/v3WF4_XrquI/mqdefault.jpg)
It's nice to see a precise sled without the usual base plate supporting the workpiece. For small table saws, every mm of usable blade depth is valuable!
Thanks for watching sir.
What an awesome job and a beautiful sled. The only thing I could say is (being a retired woodworker and professional table saw operator for over 40 years ) when cutting wood on a table saw use constant motion while pushing the wood piece past the saw blade. Been telling this to trainees for years. I noticed you scar the wood as you stop and it can be plainly seen on the wood pieces you cut. I only say this to make you a better woodworker and show the public an even better you. I intend to make one of these designs when I open my shop. It's a really good design.
Thanks for sharing.
Это великолепно... Обязательно сделаю себе такие салазки 👍
Thank you for sharing this wonderful idea and excellent video. I admire your workmanship and presentation. I hope that you and your loved ones keep well in this current health crisis. Best wishes from Australia.
Thanks for your kindness.
Please stay safe with your family sir.
👍
Obrigado por essa excelente ferramenta meu amigo por esse excelente trabalho que DEUS te abençoe e te guarde
Great cross cut build!... I need to make one like that.
Beautiful work I always enjoy your content it’s very relaxing to watch too
Um projeto muito bem elaborado e feito com carinho e muita precisão. Uma ideia a ser adotada por quem padece com o excesso de peso de uma guia para realizar cortes em sua mesa de serra circular. Só reluto no emprego daquelas duas guias paralelas, de pinnus, pois sendo uma madeira macia, não demorará a sofrer desgaste dentro dos canais da mesa que o acomodam, caso o ritmo de trabalho seja intenso. Quanto ao resto, só elogios. Parabéns!
Thanks for watching sir.
Oktober pp oleh karena itu saya tidak 9
I didnt understand how the scale would work... what was it registered to? Otherwise an excellent cross cut sled and on my to do list now :)
Excelente projeto é uma bela ferramenta parabéns, obrigado por compartilhar seus conhecimentos ...saudações aqui do brasil.
Cool, this is a great tool for tech carpenter! Wood cutting work will be convenient and fast, highly accurate.
best cross cut sled on utube!!!
Another Basic Craftsmans Shop Project. Excellent 👍
Thanks again sir.
👍
ОТ ВЕЛИКОГО до простого- один шаг! Спасибо за идею! завтра с утра устремлюсь к станку!
😀👍КЛАСС!
Thanks for watching sir.
I really enjoy your projects and how you make your videos. Thanks for doing this.
Excellent job! I'm going to do this myself.
Grande precisione, grande maestria e soprattutto una esecuzione con grande eleganza.
Claudio Lorusso
Just a suggestion, wouldn't it be easier to glue up the two rabbeted boards then cut the bolt slot? I liked the method how you squared the unit to the blade. Excellent quality workmanship and attention to detail. The pointer is a nice touch. Thanks for sharing. Looking forward to your next video.
Thanks for watching sir.
You can also use a t-slot router bit which will cut the channel in one shot, so you don't have to perform multiple cuts. Those have saved a lot of time for me.
Yes, if you have a router table and T-slot bit, not everyone does. What he shows you here is basically is how to build this without a router table so in essence he’s showing people two different ways simultaneously. (Assuming, like you, knowledge of what a T-slot bit does) I, too, admire is attention to detail and creativity. I only wish I had his patience instead of my usual practice of going a hundred miles an hour and trying to build everything in one day!
@@Erik_The_Viking I use table saw to cut a line first to remove some material for t-slot router bit go through easier.👍💪💖
@@206Seaman I make t-slots without a router table as it's easier to use an edge guide for more control.
You might credit John Heisz with this design a year earlier.
Japan 1- 0 USA
very nice...you are very good in woodworking ,I really enjoy watching your vedeos thank you and God Bless!!!
As always, well conceived, built and recorded. A jig well worth the time and effort to build. Cheers!
C. ㅍ ㅎ ㅕ. 하지만
Бриллиантовые руки золотая голова!
Excellent sled, video and work. I'm confused about one thing, when you attached the rule tape to the top, why did you go with this positioning vice zeroing it at the blade?
Show de bola companheiro!
That was wonderfully satisfying
Saudações do Brasil amigo. Seu trabalho é lindo, limpo e impecável . Conquistou-me como inscrito e seguidor. Vou tentar seguir seu exemplo. Muita paz, saúde e felicidade. Obrigado.
14:10 I wonder if those bolts provide enough thread engagement to hold the plastic :)
Show, show..., ficou excelente, belíssimo dispositivo, facilita e muito o dia dia no trabalho! PARABÉNS mesmo
Abraço aqui do Brasil 🇧🇷
Thanks for watching sir.
👍
It's funny I should see this today. I have been trying to come up in my mind a way to set the fence angle accurately without all the trial and error. My idea was to cut a 1" board on the right side using the miter slot and bouncing the square off it, LOL. The difference is that I plan to make a split sled where the left side or right side can be used independently or together as one sled.
I see I saw this video in the past, so maybe that's where my mind picked it up. I have a lot of creative ideas, but I mostly get them from parts of many different sources over the years. I just sort them out to make one good idea from them.
Thanks for the video. I needed this one today.
Thanks for watching sir.
Credit should go to John Heisz for his design.
VERY well done and great idea. Also great camera and editing. Thank you!
Thanks for watching sir.
👍
thank you very much for your creations they are very interesting and beautiful
Perfect job. Thanks for sharing the video.
Very well done. Great precision and craftmanship. I really liked the clamp you were using at the beginning. That looks very useful.
Simple but very effective and we’ll layer out take care 😀👍
Thanks for watching sir.
👍
Hello nice job! Have you link of your powermatic saw ? I have gts 10xc, and can i know why you have changed ? Ty very much 👍
Ottimo lavoro e sicuramente molto pratica visto la manegevolezza. Saluti e complimenti
Exellent, just a minor remark: I would have bought a measure from right to left, so it is easer to read from where you are standing.
Excellent ! Good idea and a nice job ! 👌 👍 👍
Greetings from Austria 🙋♂️ Leo.
Thanks for watching sir.
Greetings from Korea.
Espero que se entienda lo que quiero decir...usted y muchos de ustedes hermanos del otro lado del mundo oriental poseen un nivel de alto desarrollo de los ingeniería aplicada, con un grado de simpleza y practicidad, una visión más amplia y un nivel de detalles sorprendente que no logro ver por este otro lado del mundo occidental. Siempre encuentro estas características al ver videos relacionados al bricolaje y creo que lo he comentado con otras personas y muchos dicen que son una raza superior y usted confirma lo que le comento. Si existiera la posibilidad de volver a nacer... desearía estar desde el otro lado para confirmar mi observación. Muy agradecido por su trabajo y experiencia saludos cordiales 🖐️ desde Chile 🇨🇱
Thanks for watching sir.
Perfect! I'm making it
Excellent work, my friend. Really well done! 😊
Stay safe there with your family! 🖖😊
Thanks for watching sir.
Special thanks for your kind concern.
Please stay safe with your family too.
So clean, so precise, so smart.
Thanks for watching sir.
Very nicely done. Clever design, nicely explained. Thumbs up to crush a troll.
Thanks for watching sir.
Te felicito , con tu permiso me hare uno ogual , gracias por compartir
Cómo puede ser?? Todos sus trabajos ,por muy pequeños o grandes que sean tienen un magnífico resultado final , gracias por compartir tanta creatividad y conocimientos , un saludo cordial y por supuesto un gran like desde Narón , Galicia (España) 😜🤓🤣
Thanks for watching sir.
👍👍👍
Beautiful, excelent job, congratulations.
Thanks for watching sir.
👍
Muhteşem. Harika bir çalışma, ellerine sağlık. Türkiye den sevgiler.
Salah satu chanal favoritku. Bebeberapa Vidio aku dowload dan kali ini, saya mohon izin untuk mendowloanya
Tout simplement : "MAGNIFIQUE"...
Congratulations from Brazil! Excellent idea! A very good tool!
Thanks for watching sir.
Valeu meu amigo show de bola muito bacana o projeto do gabarito muito boa à demonstração
where is the tape measure measuring from, saw blade? It appears way off, but all in all simple but a great idea.
It measure from the saw blade.
Thanks for watching sir.
Looks like it isn't
As with your tenoning jig I made for myself I will be making one of these as well. Nicely done sir!
Thanks for watching sir.
Спасибо ! Круто !
Thanks for watching sir.
excelente trabajo, saludos desde Tabasco, México
superbe réalisation. j'adore tes tutoriels, merci pour tous tes partages.
Thanks for watching sir.
Parabéns pelo excelente projeto!
Thanks for watching sir.
👍
Little..but ..special ! Like it ,Greetings again from us 🌷🌷🌷
Thanks for watching sir.
Increible trabajo, valoro su creatividad, al principio no suponía utilidad y al final vi que es tremendamente útil, felicidades, su like y desde luego me suscribo, saludos desde el Puerto de Veracruz, México.
다른것을 계획하구 계시군요. 과연 다음에 어떤 작품이 나올지 궁금해 지내요...
당분간 제 공방에 필요한 지그들을 만들어볼 생각입니다.항상 고맙습니다.
👍👍👍
Great Woodworking Skills. Love Your Jigs
Thanks for watching sir.
Excelente trabajo. Es una idea fantastica Saludos desde Bolivia
Thanks for watching sir.
Greetings from Korea.
Hasil kreativ yang baik,,🙏👍❤️
Hi. Very interesting video.
Malaysia going for lockdown again, begining 1st June to 14th June.
Sorry to hear that. Please stay safe and be healthy with your family. I hope everything will be OK as before. Thanks for watching sir.
👍
Nice build J! Do you have any plans or dimensions?
Sorry I don't have any plans for both this and others. I make with hand sketchs. Thanks for watching.
👍👍
muito bom mesmo pena que nao tem as medidas cos componentes sena eu poderia tentar fazer uma parecida
Very nice sled and excellent video. Well done.
Thanks for watching sir.
Beautiful 👏
Good job ! 👍🏼
Thanks for watching sir.
прелестно. результат и сам процесс. почти медитация.
Thanks for watching sir.
👍😀
Really, really nice!!! …… As usual !!!
merci pour tous tes partages.
Thanks for watching sir.
Excellent👏👏👍 Norbert ( France )
Thanks for watching sir.
prachtig en betere beveiliging spouw mes achter de zaag
Наверное, было-бы более технологично, если склеить две массивные детали и уже затем осуществить пропил зазора под болт. 1:15
А сама идея мне очень понравилась.
Спасибо.
Parabéns pelo seu projeto ficou muito bom 🇧🇷🤝💯
Thanks for watching sir.
👍
Good job Sir
Thanks for watching sir.
Nice build
Thanks for watching sir.
Отлично! Удачи!
Thanks for watching sir.
Complimenti bellissimo lavoro
Thanks for watching sir.
Use the material like what is used for plastic cutting boards. It will no expand and slides like silk.
Beautiful work! Subscribed.
Thanks for watching and new subscription.
Al levantar las piezas recién pegadas se pueden desalinear. Mejor dejarlas sobre la mesa y usar morsetas. O poner clavitos provisorios. O al menos espolvorear sal en la unión.
정말 멋진 지그입니다. 만들어서 사용해야겠습니다. 무슨 나무인지 궁금합니다. 고무 나무인가요?
저는 영상을 위해 고무나무를 썼지만, 변형이 있습니다. 합판 사용을 추천합니다. 변형이 적지요.
감사합니다.
Good 👌👍👏
Thanks for watching sir.
Hi,
Did you use Hardwood for this project 🤔 ?
I used plywood and rubber tree panel.
Thanks for watching sir.
👍
I cant believe you still have fingures left.
Sorry. I'll be careful sir.
Thanks for watching.
Ive always struggled with the depth of cut on my smaller tablesaw with a crosscut sled.. it never occured to me to leave out the base like that..!
Thanks for watching sir.
Tão bem trabalhado, um excelente vídeo... Brasil, mais um inscrito 👍👍👍
Thanks for watching sir.
Boa noite
Trabalho de mestre
Pretty nice work, but there are much easier ways to accomplish the same thing. Waaa...y too many little parts. Really hard to keep from making an unacceptable cumulative error.
WHAT AN AWESOME BUILD!! Something else I've been meaning to make for a while but, I'm glad I waited...you have given me some great ideas. I really like the RED LINE on the clear acrylic...I may use my own blood for that...
Sorry about my belated reply.
I fell in love with my job. Very busy with thinking over and over about next videos and preparing parts which I'm not accustomed to. There are so many strange hardware, bits and parts. Those are what I break through.
Thanks buddy.
No worries about the slower replies. As your channel grows, you'll have less time to reply to these things and maybe eventually not have time to reply to any of them at all. I can certainly see that you are very diligent to reply as much as you can and you have not missed one yet. Pretty amazing actually. I'm sure it will make your subscribers very loyal to you and your content.
We are recovering from the virus. The sun will shin brightly tomorrow as before.
Take good care.
👍
That table saw seems extremely powerful. Even more so than a sawstop
Yes it is powerful.
Thanks for watching sir.
Gostei. Vou fazer um deste pra substitui o meu, já muito estragado pelo uso.
E massa viu eu quero aprender a fazer.
mm, cm ????? Pako?
Excelente realmente es buen video gracias
wonderful
👍 классно!
very good idea.
Thanks for watching sir.