Hi Dean. I have a 2 Audi Allroads with same suspension setup. 55 plate(C5) and 60 plate(C6). These have self levelling suspension so if one corner drops the car compensates by dropping the others. Lift the car to maximum height and put it into jacking mode via the MMI. This will disable self levelling and if you have a leaking airbag, only the faulty corner should drop. As posted earlier, it would also be advisable to replace the air compressor relay with an upgraded version. Good luck👍
Dean, this is why you have 87k subscribers, because they want to see cars like these being bought and repaired. It's why I look forward to every video you put out. I'm sure it will be worth the cost and effort to get this car back on song.
TPI for suspension leaks. The orange, purple air lines rub on the chassis and get pin hole leaks. TPI give a part number for new air lines and connection, then you have to re-route the lines away from the chassis.
This car is my daily driver. I too had to change the compressor: I first cheaped out on the refurb kits (to no avail), followed by the 200 quid compressor (repackaged China) from a UK ebay seller, which only lasted me 4 months. I then bought the original OEM WABCO for around 400 euro from Germany. That one is working great, fingers crossed:). I also changed the valve block (just because I wanted to) and two strut valves. Luckily, my bags are not leaking, but I have a guy who can replace the rubber sleeves for 80 euro a pop (no need to buy a new strut). It is also important to change the plastic height sensor linkages because they seize over time; one UK ebay seller sells adjustable linkages made out of metal. Mine were super seized. And, don't forget to change the compressor relay; it comes with the new compressor.
I had this exact same fault with my Q7. Turned out I had a slight leak in one of my front airbags which made the compressor overwork blowing the fuse. I had the fuse replaced and ran it but ended up frying the compressor a few weeks later. Had 2 new front bags and a compressor fitted,problem solved. I have a brand new air block for the back of the compressor sat in my garage that wasn’t fitted. If you need it you can have it for the price of postage and a couple of pints😁
I've got a 4.2 one of these and believe me that pump has had it, you cant hear mine even when you know it's running. There are also holding valves at the top of each air bag the maintain the level and they deteriorate over time.
Thanks Dean, loved this video I have a 2007 Q7 so no doubt will have suspension issues. I have changed the relay under the dash as a precaution but wasn’t aware of the 2nd by the battery. Looking forward to part 2
Transformation was very satisfying 😁 breaks my heart to see how badly some people treat their cars 😩 Good job Dean, keep on working thru the issues. Love these videos!
I've been working at a body shop for a bit now and extra tips I learned was if you're painting the door, it's better to take off the mirror and belt molding (the trim at the bottom of the window) for a better paint job in the end. The mirror can get in the way, and if you're unlucky, the clear coat could stick in that gap between the door and the belt molding.
Look, each bag has 2 o rings. Get the o Rings, the inner bumpstop and some silicone grease. Get it apart and just replace it. You might only need that work done. I think you need the upper air valve new too.
youve had a right result Dean..for sure this is a keeper,,the outside is cosmetic no problem for a man of your means,,have a good weekend Dean looking forward to the finish on this one,👌👌👍
Remove the Vindis sticker off the back, will improve the value :D Always wound me up how they continued to put those on long after most dealers gave up!
What a bargain. I have a 2012 Q7 had it 4 years and its been a brilliant car. I also have the air suspension and its been good as gold. One thing i will say is the compressor on yours is really loud compared to mine, which i dont really hear atall. Give that thing a nice remap! It makes a world of difference and is actually rapid at just over 300bhp and 630 nm of torque
Hi Dean, a fuse never blows for no reason. The compressor has an NTC sensor (overheat) which inhibits relay coil to shut of power. If the relay is welded shut (on) the NTC ecu control does not work, it then runs the pump forever, vents the overpressure air and burns the compressor out. It will be caused ultimately by a combination of leaks adding to increased demand on pump duty. Recently I found leaks around the joints on the front strut top aluminium housings (porus) that was the leaks and the demand. Clue was the car (cayenne-same as q7) was down on its nose in the morning. For what its worth, monitor pressure vs temp vs demand call from the ecu to determine a lazy compressor - it will be at this age, so a decent replacement around 350 quid, easy to fit plus new relay. You need however to fix the leaks. Get so soapy water in a spray bottle, with system pressurised, spray every joint, pipes, tops of air springs etc. Leaks will blow bubbles Dean - cheap and easy. Then fix the leaks...
Really impressed with your whole skills, and tenacity. I do not like complicated modern cars. Morris Marina, built out of stainless steel would be my number one choice, but I am nearly 70 yrs. Peace be unto you.
Hi Dean, I really enjoy your video's and it also served as learnings in one or another way. What happed to the Q7 is there another Video number 3 on it ?
I had the exact same symptoms, suspension bottomed out and lights on the dash. It was just the massive 40A fuse. No independents wanted to know because they couldn't diagnose the air system. A month wait for Audi to look at it forced me to Google, and found an obscure american website with one reference to that fuse. Cost me a couple of quid to fix and had years of happy motoring aftwerwards. Felt like I'd won the world cup after looking at the potential costs.
As everyone said pump is unusually loud and poss pinholes in pipes/bags valves. Good luck love the cheap flip vids also. Great variety on the channel. Excellent work as usual dean. Was looking for a 4.2 petrol v8 FSI Q7 but are rare as hens teeth lately. You did super well for a grand but it’s poverty spec no Xenons no colour mfd or colour mmi to name a few lacking options or likes of Xenons, pan roof etc etc. at least it’s an sline that’s a biggie!
I had a 2007 3.0 diesel. That orange fuse would blow maybe twice a year. You can just squeeze your hand in under seat to replace it (no need to undo any bolts) Moved it on eventually when the boot motor and infotainment started to play up. It was nice when newish, but those electric gremlins sure do come thick and fast as it ages.
I would buy this car in a heartbeat, no questions asked. It is a good buy in my opinion. The interior looks great ! I wish I could find a car like this for a 1000 euro. Good luck on fixing the air suspension.
I reckon your Audi is a score. I had Air Suspension problems on my Mercedes and the stealership wanted over $10k when I first took it to them. I fixed it all myself using aftermarket parts for a few hundred dollars! Cheers Drew
Great buy looks nice I know some attention brings it back to life I own a Q7 2009 currently at the shop as it has a leak on the valve head cover ordered a aluminum one as I will keep it running. Has 185,000 miles and still drives Amazing.
Dean, a common fault on q7 is connection to air bag from air pipe. With time it corrodes and leaks air. One of the solutions is to take a copper washer and replace it in that connection.
Audi drive beautifully. However it can be a nightmare under the hood. Changing the timing chain can be a monster job. On a older one that has yet to show any problems, I would change the timing chain tensioner and cross my fingers. You can always drop the oil pan to see if chunks of the timing chain guides are there and of course look for any glitter or chunks.
Wife had the exact same issue with hers - thankfully fixed under warranty. Further cemented my love of older uncomplicated cars but hey... the Audi's nice while it works lol
Audi and VW never seen to reduce the price of parts. Things that were super expensive options in 2007 (like air suspension) still carry the same crazy prices, even though China now makes the part for 1\10 of the price.
If you had to keep a part in stock for 17 years what return would you want on your investment? The chinese knockoff will last to the end of your driveway, but it's cheap.
@@einfelder8262 I get what you're saying about the quality, obviously it's not going to be OEM, but a lot of the recent Chinese products have got way better. £3k vs £120, the quality gap isn't going to be anywhere near that order of magnitude
@@ianmontgomery7534 If Audi or any other OEM orders a product to be made to their spec, the Chinese factory will make a batch that way, have it passed by quality control while nodding heads in assurance, and then make the next ones with massive reduction in quality. They do this by using, for example, cheap alloy made from recycled heads or other aluminium stuff, complete with all impurities, rather than a specified high grade alloy. I have seen a "steel" caravan suspension A arm that broke and couldn't be welded because it was made from cheap cast iron...... So, knockoff or "OEM" spec, Chinese stuff can be trusted to be junk.
SAME air pump issue on my 2006 Q7 - I solved it all for £190 with Labour when Audi quoted £3,500 thieves! MMI unit now blown, and the tailgate sounds like a machine gun. Can’t sell it coz of tax and emissions and fuel consumption is now double what it used to be - breaking for Spares (Newcastle)
That's a great point about fuel consumption doubling with age on secondhand cars. Which goes to show most people in the secondhand market on a budget are better off getting something economical to begin with. Not some gas guzzling speed racer job they can just about afford.
When the pump is that noisy it basically Knackered, the new one will be a lot quieter, that said you likely have a leak in one of the air shocks, you need to replace or you will wear out the new pump in short order. I had this issue on an X5, ended up whipping out the bags and put in springs.
It's a nice car and given your abilities and willingness to use ebay/pattern parts, it's an easy choice, fix it and ditch the pickup! Good luck and keep posting the great videos.
Hi Dean. Not a car for me. But saying that. I think your on the right track with a repair. Also plenty of suggestion in other comments, on where to go next. See you in the next one. 👍👍
Its the self leveling valve moudule. Common fault as it is a service item always neglected. They get corroded over time and leak air. The item cannot be refurbished as it is sealed. You have to replace it. The pump has over heated because its not meant to come on that often and it should not run more than 2 minutes otherwise it will overheat.
If the blown fuse has blobby ends to the break it’s an overload, if it has clean ends to the break it’s a short circuit. The mats you can wet vac and put carpet dye in the wet vac water to stain them back to grey.
Typical air suspension fault is due to oxidation build up on the connectors .. had a similar fault on a w205 c class , merc as usual recommended by replacing the compressor without checking.. long story short cleaned out the oxidation build up and sealing jt better than factory.. never had a problem since
The original compressor on my CLS jammed on, which overheated it and resulted in it melting the power connector. It still worked after this but it got progressively worse. If you've ordered a new compressor you should probably still fit it
On the land rover ones there’s a big rubber o-ring seal that goes we used soapy water in a spray bottle. Aftermarket bag kits aren’t to dear if worst comes to worst.
Was in a scrappers yesterday plenty of recent-ish Audi's - no Q models oddly - appalled to see doors left wide open to the weather, presumably by customers, and leather interiors getting moldy. I must have looked obsessive, I closed over 20 doors. Quite a few had Bose sound systems in them complete with door cards, cheap upgrade if you like your music - simple plug n play surely?
It’s got to be excellent value for money as you could part it out and get your initial outlay back and then some, though as I like the Q7 SUV I hope you will continue and find the leak(s), have it mot’d and use it as your daily still 👌🏼
Had the same problem with a merc w205, fuse blown quite a while back replaced it along with the pump because it was seized. After a few months the car came back because it was losing rear hight, replaced both rear airbags and did solved it, it was a tiny leak that wasn't always showing up
I clicked on this video wondering if you'd mention towing capacity, and you did! I've been on the hunt looking for a vehicle with space enough to carry Tools + 4 Wheels (and fitted tyres), as well as have weight left over to tow up to 2T at least.
The left rear air strut is bad and makes them all leak . I had a allroad and the corner that leaned was the bag that leaked . I got them at airnot industries and they come with lifetime warrenty . I love these q7 s ❤️
I had a ABS ECU failure on an A6 2.5 V6. Audi said 1500 for the part and probably same again for the labour. Did a bit of googling and found a place in the UK that reconditioned the ABS ECU , £52 GBP and a video to show you how to fit it in 45 mins. bba-reman was the name of the crowd who reconditioned it.
Replaced two rear bellows on 5 series touring for just £80 the pair, decent quality off Ebay, BMW wanted in excess of £2,000 for exactly the same job. And it only took me 3hrs. Oh and that was 18 months with no issues since. Lesson learnt.
I see you found out that Audi pile on a huge mark-up! Many years ago I worked for a systems supplier to Audi and one day an unhappy member of the general public (owning a C5 A6) managed to find the contact details for my employer and phoned up to try to find out if Audi were ripping him off for some component / system that we manufactured. The receptionist put the call through to me and....yes, I had to tell him (strictly off the record, of course...) that Audi were quoting him approximately seven times the price of what my employer would charge Audi to supply said item. The gentleman's next question was - would it be possible for him to acquire it directly from my employer...? I had to tell him that car manufacturers make their profits by screwing their suppliers in the first instance and then screwing their customers for any spare parts in the second instance. If it had been up to me, I would have given him contact details for our sales division and suggested that they open up a little sideline to bypass Audi on spare parts, but sadly that was far above my pay grade! How I (do not) miss the automotive industry....
Hi dean car looks cheap as for your presentation you are very good clear and knowledgeable,don’t try to fit everything into one video keep the audience captivated Suggest you check out mat Armstrong and Chris slix I will enjoy all you’re videos I would like to see more rebuilds etc even up grades and car trips with mrs and kids keeping it real
May have been mentioned in previous comments however maybe try a smoke generating machine doo dad (used for vacuum leaks etc) to find the leak(s). Just a thought 😁🤔
So Audi, having proper diagnostics failed to see the fuse was blown?? WTF , that's scandalous there is no way they missed that fault and just wanted to charge £££.
Wrong. Audi knew the fuse was blown, they knew the pump sounded like an asbestos lung, and they knew all 4 airbags and lines needed replacing and they are required to give their work a sensible warranty, along the lines that the air system would be trouble free for xxxx thousand miles or 1 year. I don't know the UK consumer laws but would be surprised if a dealer could charge to fix something and have it fail a month later without the consumer being protected.
Always start the engine when You refeeling struds. From the lowest position when its goes to one of the levels. Never start kopmressor again. Let him cool down. With vcds on live data You can see temp of the kompressor.
Going through a similar issue myself. Bmw f11 2012, rear compressor for the airbags, new one off ebay 2 years ago now rusting from the inside out. Now have to buy a genuine one. Steer clear of the ebay rubbish. If it seems too good to be true, it probably is. Sellers don't reply when there's an issue with the item..
Vehicles with the steering wheel on the right, and some making their way to where I live as reconditioned units - I'm subscribing to this channel. --Petaling Jaya, Malaysia
These VAG prices are getting ridiculous. I just got quoted £180 from TPS for a rear wheel hub and bearing assembly. I ended up buying a good quality pattern item for £50!!
Older big SUV's may sound tempting for the price but they can be a total money pit. I bought a 2003 X5 3.0D Sport cheap a few years back. Ended up needing an automatic gearbox and a turbo. Not to mention the last owner had snapped all 6 glowplugs when they attempted removal...
Hi Dean. I have a 2 Audi Allroads with same suspension setup. 55 plate(C5) and 60 plate(C6). These have self levelling suspension so if one corner drops the car compensates by dropping the others. Lift the car to maximum height and put it into jacking mode via the MMI. This will disable self levelling and if you have a leaking airbag, only the faulty corner should drop. As posted earlier, it would also be advisable to replace the air compressor relay with an upgraded version.
Good luck👍
Thanks bud! Great tip 👍🏽👍🏽
@@SavingSalvage also check valve block and residual pressure valves had this on our old q7
@@SavingSalvage lol the black thumbs up
How is your experience with the c6? I planned buying one but the extra costs turned me off. How much you spend on upkeep per year and much you use it?
Jack pot
Dean, this is why you have 87k subscribers, because they want to see cars like these being bought and repaired. It's why I look forward to every video you put out. I'm sure it will be worth the cost and effort to get this car back on song.
0p
TPI for suspension leaks. The orange, purple air lines rub on the chassis and get pin hole leaks. TPI give a part number for new air lines and connection, then you have to re-route the lines away from the chassis.
This car is my daily driver.
I too had to change the compressor: I first cheaped out on the refurb kits (to no avail), followed by the 200 quid compressor (repackaged China) from a UK ebay seller, which only lasted me 4 months. I then bought the original OEM WABCO for around 400 euro from Germany. That one is working great, fingers crossed:). I also changed the valve block (just because I wanted to) and two strut valves. Luckily, my bags are not leaking, but I have a guy who can replace the rubber sleeves for 80 euro a pop (no need to buy a new strut). It is also important to change the plastic height sensor linkages because they seize over time; one UK ebay seller sells adjustable linkages made out of metal. Mine were super seized.
And, don't forget to change the compressor relay; it comes with the new compressor.
I had this exact same fault with my Q7.
Turned out I had a slight leak in one of my front airbags which made the compressor overwork blowing the fuse.
I had the fuse replaced and ran it but ended up frying the compressor a few weeks later.
Had 2 new front bags and a compressor fitted,problem solved.
I have a brand new air block for the back of the compressor sat in my garage that wasn’t fitted. If you need it you can have it for the price of postage and a couple of pints😁
Nice
@@VioletGiraffe I know exactly how fuses work. My ‘overworked’ compressor was probably the cause of the blown fuse which is what the garage said
@@B1ddy( I know exactly how fuses work ) You don t :)))) So if you left the electric cooker on for 1 week on , the fuses blow ! THAT IS OVERWORK ! LOL
I've got a 4.2 one of these and believe me that pump has had it, you cant hear mine even when you know it's running.
There are also holding valves at the top of each air bag the maintain the level and they deteriorate over time.
I thought that pump sounded a bit noisy
Also very slow to pump up the system
Damn Germans can nothing ever be simple on these cars
I've always been in love with these vag big suvs, q7, touareg, cayenne they are so cheap.. But the bills that come with it usually it's scary
In the meantime the guy who sold you the car is kicking himself screaming "A flipping fuse"
Tbf if he never tried a fuse then he's a dope 🤷 hahah
More like the audi tech needs to check the basics
@@shaunfry3202 to be fair they probably did which is why it's more than just the fuse
Finish the vid before commenting, bozo
@@slimeprivilege I had, it was a thought about the initial finding bozo
The tank of fuel is almost more than you paid for the car.
so true!!!😅
The fuel could have gone bad while it stays unused
@@SapphireEngineering Mix with fresh. Diesel dont mind it
only thing wrong is it’s a bit dirty
@@gimek92 might as well mix with peanut oil😂 still works
The car starts and drives and you bought it for 1000,man this is a win theres no way you can make a loss on this.
Thanks Dean, loved this video I have a 2007 Q7 so no doubt will have suspension issues. I have changed the relay under the dash as a precaution but wasn’t aware of the 2nd by the battery. Looking forward to part 2
Transformation was very satisfying 😁 breaks my heart to see how badly some people treat their cars 😩 Good job Dean, keep on working thru the issues. Love these videos!
I've been working at a body shop for a bit now and extra tips I learned was if you're painting the door, it's better to take off the mirror and belt molding (the trim at the bottom of the window) for a better paint job in the end. The mirror can get in the way, and if you're unlucky, the clear coat could stick in that gap between the door and the belt molding.
Great car. I want a 2010-ish Q7, but without air suspension - that seems to be one of the biggest problems with this model.
Low mileage on the odometer, could be a cheap and comfy towing bus 💪🏻
Look, each bag has 2 o rings. Get the o Rings, the inner bumpstop and some silicone grease. Get it apart and just replace it. You might only need that work done. I think you need the upper air valve new too.
youve had a right result Dean..for sure this is a keeper,,the outside is cosmetic no problem for a man of your means,,have a good weekend Dean looking forward to the finish on this one,👌👌👍
Really appreciate your diagnostics and description of the problems and how you went about fixing it.
Remove the Vindis sticker off the back, will improve the value :D Always wound me up how they continued to put those on long after most dealers gave up!
What a bargain. I have a 2012 Q7 had it 4 years and its been a brilliant car. I also have the air suspension and its been good as gold. One thing i will say is the compressor on yours is really loud compared to mine, which i dont really hear atall. Give that thing a nice remap! It makes a world of difference and is actually rapid at just over 300bhp and 630 nm of torque
Make sure you drain the plug because water will get in the ecu.. a blow it. It happened to me 🤦♂️👍
Hi Dean, a fuse never blows for no reason. The compressor has an NTC sensor (overheat) which inhibits relay coil to shut of power. If the relay is welded shut (on) the NTC ecu control does not work, it then runs the pump forever, vents the overpressure air and burns the compressor out. It will be caused ultimately by a combination of leaks adding to increased demand on pump duty.
Recently I found leaks around the joints on the front strut top aluminium housings (porus) that was the leaks and the demand. Clue was the car (cayenne-same as q7) was down on its nose in the morning. For what its worth, monitor pressure vs temp vs demand call from the ecu to determine a lazy compressor - it will be at this age, so a decent replacement around 350 quid, easy to fit plus new relay. You need however to fix the leaks. Get so soapy water in a spray bottle, with system pressurised, spray every joint, pipes, tops of air springs etc. Leaks will blow bubbles Dean - cheap and easy. Then fix the leaks...
Just found you on the Tubes, great video and great production. Thank you!
Nice for a grand, always fancied one of these but got scared off by the hype of how complicated they are, so looking forward to this series 👍
New to the Chanel but I like you’re no nonsense approach and will continue watching
Really impressed with your whole skills, and tenacity. I do not like complicated modern cars. Morris Marina, built out of stainless steel would be my number one choice, but I am nearly 70 yrs. Peace be unto you.
What an absolute bargain for £1k, was expecting it to have very high mileage. But only 68k is very low. Can't wait for the next video dean 👌👍
Hi Dean, I really enjoy your video's and it also served as learnings in one or another way. What happed to the Q7 is there another Video number 3 on it ?
I had the exact same symptoms, suspension bottomed out and lights on the dash. It was just the massive 40A fuse. No independents wanted to know because they couldn't diagnose the air system. A month wait for Audi to look at it forced me to Google, and found an obscure american website with one reference to that fuse. Cost me a couple of quid to fix and had years of happy motoring aftwerwards.
Felt like I'd won the world cup after looking at the potential costs.
As everyone said pump is unusually loud and poss pinholes in pipes/bags valves. Good luck love the cheap flip vids also. Great variety on the channel. Excellent work as usual dean. Was looking for a 4.2 petrol v8 FSI Q7 but are rare as hens teeth lately. You did super well for a grand but it’s poverty spec no Xenons no colour mfd or colour mmi to name a few lacking options or likes of Xenons, pan roof etc etc. at least it’s an sline that’s a biggie!
I had a 2007 3.0 diesel. That orange fuse would blow maybe twice a year. You can just squeeze your hand in under seat to replace it (no need to undo any bolts)
Moved it on eventually when the boot motor and infotainment started to play up. It was nice when newish, but those electric gremlins sure do come thick and fast as it ages.
I would buy this car in a heartbeat, no questions asked. It is a good buy in my opinion. The interior looks great ! I wish I could find a car like this for a 1000 euro. Good luck on fixing the air suspension.
I reckon your Audi is a score. I had Air Suspension problems on my Mercedes and the stealership wanted over $10k when I first took it to them. I fixed it all myself using aftermarket parts for a few hundred dollars! Cheers Drew
Replace the rear airbags I got cheap ones off eBay £200 they worked a treat
Looking forward to the next part, believe you have great value and a good car in the long run! 👍
Love it when these deals come along!
I was hoping that you wasn't going to wash it yet Dean, I'd love to clean something like that. The before and after shots would be awesome 👌🏼
Great buy looks nice I know some attention brings it back to life I own a Q7 2009 currently at the shop as it has a leak on the valve head cover ordered a aluminum one as I will keep it running. Has 185,000 miles and still drives Amazing.
Great vid Dean, can't wait for part two!
Dean, a common fault on q7 is connection to air bag from air pipe. With time it corrodes and leaks air. One of the solutions is to take a copper washer and replace it in that connection.
New to your channel and very impressed on first visit Hope you get a good fix without to much expense
Great video, what a result getting it useable with just a fuse!
Audi drive beautifully. However it can be a nightmare under the hood. Changing the timing chain can be a monster job. On a older one that has yet to show any problems, I would change the timing chain tensioner and cross my fingers. You can always drop the oil pan to see if chunks of the timing chain guides are there and of course look for any glitter or chunks.
Wife had the exact same issue with hers - thankfully fixed under warranty. Further cemented my love of older uncomplicated cars but hey... the Audi's nice while it works lol
Audi and VW never seen to reduce the price of parts. Things that were super expensive options in 2007 (like air suspension) still carry the same crazy prices, even though China now makes the part for 1\10 of the price.
If you had to keep a part in stock for 17 years what return would you want on your investment? The chinese knockoff will last to the end of your driveway, but it's cheap.
@@einfelder8262 I get what you're saying about the quality, obviously it's not going to be OEM, but a lot of the recent Chinese products have got way better.
£3k vs £120, the quality gap isn't going to be anywhere near that order of magnitude
@@MattyEngland We in Australia actively avoid chinese stuff as much as possible, due to them waging trade war against us.
@@einfelder8262 Are they knock offs or ones made for the Audis that are made in China?
@@ianmontgomery7534 If Audi or any other OEM orders a product to be made to their spec, the Chinese factory will make a batch that way, have it passed by quality control while nodding heads in assurance, and then make the next ones with massive reduction in quality. They do this by using, for example, cheap alloy made from recycled heads or other aluminium stuff, complete with all impurities, rather than a specified high grade alloy. I have seen a "steel" caravan suspension A arm that broke and couldn't be welded because it was made from cheap cast iron...... So, knockoff or "OEM" spec, Chinese stuff can be trusted to be junk.
Just stumbled on to your site. Great video, thanks.
Full tank of fuel a bit suspect. Hopefully no faulty fuel pumps
SAME air pump issue on my 2006 Q7 - I solved it all for £190 with Labour when Audi quoted £3,500 thieves! MMI unit now blown, and the tailgate sounds like a machine gun. Can’t sell it coz of tax and emissions and fuel consumption is now double what it used to be - breaking for Spares (Newcastle)
That's a great point about fuel consumption doubling with age on secondhand cars. Which goes to show most people in the secondhand market on a budget are better off getting something economical to begin with. Not some gas guzzling speed racer job they can just about afford.
When the pump is that noisy it basically
Knackered, the new one will be a lot quieter, that said you likely have a leak in one of the air shocks, you need to replace or you will wear out the new pump in short order. I had this issue on an X5, ended up whipping out the bags and put in springs.
It's a nice car and given your abilities and willingness to use ebay/pattern parts, it's an easy choice, fix it and ditch the pickup! Good luck and keep posting the great videos.
Hi Dean. Not a car for me. But saying that. I think your on the right track with a repair. Also plenty of suggestion in other comments, on where to go next. See you in the next one. 👍👍
Its the self leveling valve moudule. Common fault as it is a service item always neglected. They get corroded over time and leak air. The item cannot be refurbished as it is sealed. You have to replace it. The pump has over heated because its not meant to come on that often and it should not run more than 2 minutes otherwise it will overheat.
Whats wrong? The steering wheel on the wrong side.
Do an air suspension delete... There are kits for around £1k
If the blown fuse has blobby ends to the break it’s an overload, if it has clean ends to the break it’s a short circuit. The mats you can wet vac and put carpet dye in the wet vac water to stain them back to grey.
Typical air suspension fault is due to oxidation build up on the connectors .. had a similar fault on a w205 c class , merc as usual recommended by replacing the compressor without checking.. long story short cleaned out the oxidation build up and sealing jt better than factory.. never had a problem since
Love you're honestly regarding the door. We've all been there 🙂
The original compressor on my CLS jammed on, which overheated it and resulted in it melting the power connector. It still worked after this but it got progressively worse. If you've ordered a new compressor you should probably still fit it
On the land rover ones there’s a big rubber o-ring seal that goes we used soapy water in a spray bottle.
Aftermarket bag kits aren’t to dear if worst comes to worst.
Was in a scrappers yesterday plenty of recent-ish Audi's - no Q models oddly - appalled to see doors left wide open to the weather, presumably by customers, and leather interiors getting moldy. I must have looked obsessive, I closed over 20 doors. Quite a few had Bose sound systems in them complete with door cards, cheap upgrade if you like your music - simple plug n play surely?
It’s got to be excellent value for money as you could part it out and get your initial outlay back and then some, though as I like the Q7 SUV I hope you will continue and find the leak(s), have it mot’d and use it as your daily still 👌🏼
Always entertaining...
Thanks for sharing...
Just swap it out for conventional springs and shocks save yourself and everyone else the hassle! Good luck bud
Had the same problem with a merc w205, fuse blown quite a while back replaced it along with the pump because it was seized. After a few months the car came back because it was losing rear hight, replaced both rear airbags and did solved it, it was a tiny leak that wasn't always showing up
Another good one again. Looking forward to the next video.👍
I clicked on this video wondering if you'd mention towing capacity, and you did!
I've been on the hunt looking for a vehicle with space enough to carry Tools + 4 Wheels (and fitted tyres), as well as have weight left over to tow up to 2T at least.
The left rear air strut is bad and makes them all leak . I had a allroad and the corner that leaned was the bag that leaked . I got them at airnot industries and they come with lifetime warrenty . I love these q7 s ❤️
Common fault on these is an intermittent sticking relay, which is probably why the fuse blew. Located under the drivers side dash.
The compressor piston is normally the culprit, £30 rebuild kit and easy diy for fix 👍🏼
I had a ABS ECU failure on an A6 2.5 V6. Audi said 1500 for the part and probably same again for the labour. Did a bit of googling and found a place in the UK that reconditioned the ABS ECU , £52 GBP and a video to show you how to fit it in 45 mins.
bba-reman was the name of the crowd who reconditioned it.
Looks a good one for a grand ,about time your luck changed get the soapy suds out you’ll soon find it good luck lad 👍👨🏻🏭
Dean you got a bargain it might be the pump letting by 👍🏻
Wow impressed 👍 you have a car 🚗 that starts …. Thats a change dean 👍
Replaced two rear bellows on 5 series touring for just £80 the pair, decent quality off Ebay, BMW wanted in excess of £2,000 for exactly the same job. And it only took me 3hrs. Oh and that was 18 months with no issues since. Lesson learnt.
Wow a whole tank of fuel !! Thats got to be £150 off the price right there!
Perfect for parking as close to the supermarket entrance as possible. Clear coat it to preserve that 'weathered' look.
Dean what is the diagnosis tool you are using
Great Video, Can i ask what your diagnostic machine is please
👀looks like it's might be a cheapish one for you fella✌️😎👍 buzzing
I see you found out that Audi pile on a huge mark-up! Many years ago I worked for a systems supplier to Audi and one day an unhappy member of the general public (owning a C5 A6) managed to find the contact details for my employer and phoned up to try to find out if Audi were ripping him off for some component / system that we manufactured. The receptionist put the call through to me and....yes, I had to tell him (strictly off the record, of course...) that Audi were quoting him approximately seven times the price of what my employer would charge Audi to supply said item. The gentleman's next question was - would it be possible for him to acquire it directly from my employer...? I had to tell him that car manufacturers make their profits by screwing their suppliers in the first instance and then screwing their customers for any spare parts in the second instance. If it had been up to me, I would have given him contact details for our sales division and suggested that they open up a little sideline to bypass Audi on spare parts, but sadly that was far above my pay grade!
How I (do not) miss the automotive industry....
Really enjoy Your videos. Im a audi lover. And shows a few already
@13:00 was screaming 'close the doors and boot', you got there though in the end.
Do a height calibration for the suspension.
good evening... a question... what pressure must the compressor generate to be able to lift the car?
Hi dean car looks cheap as for your presentation you are very good clear and knowledgeable,don’t try to fit everything into one video keep the audience captivated
Suggest you check out mat Armstrong and Chris slix
I will enjoy all you’re videos I would like to see more rebuilds etc even up grades and car trips with mrs and kids keeping it real
What an absolute steal! Good effort 👌
May have been mentioned in previous comments however maybe try a smoke generating machine doo dad (used for vacuum leaks etc) to find the leak(s). Just a thought 😁🤔
Hi there, may I ask approximately how much you pay for your unit and where you found it? I've searching high and low for one for quite some time now
So Audi, having proper diagnostics failed to see the fuse was blown?? WTF , that's scandalous there is no way they missed that fault and just wanted to charge £££.
Wrong. Audi knew the fuse was blown, they knew the pump sounded like an asbestos lung, and they knew all 4 airbags and lines needed replacing and they are required to give their work a sensible warranty, along the lines that the air system would be trouble free for xxxx thousand miles or 1 year. I don't know the UK consumer laws but would be surprised if a dealer could charge to fix something and have it fail a month later without the consumer being protected.
@@einfelder8262 better to keep your mouth shut and look an idiot, than to open it and remove all doubt
@@einfelder8262you get warranty with repairs depending on the company performing the works
That's very cheap and a great car to fix would love to see you get some good performance out of it
Always start the engine when You refeeling struds. From the lowest position when its goes to one of the levels. Never start kopmressor again. Let him cool down. With vcds on live data You can see temp of the kompressor.
Going through a similar issue myself. Bmw f11 2012, rear compressor for the airbags, new one off ebay 2 years ago now rusting from the inside out. Now have to buy a genuine one. Steer clear of the ebay rubbish. If it seems too good to be true, it probably is. Sellers don't reply when there's an issue with the item..
What fantastic result!
Vehicles with the steering wheel on the right, and some making their way to where I live as reconditioned units - I'm subscribing to this channel.
--Petaling Jaya, Malaysia
These VAG prices are getting ridiculous. I just got quoted £180 from TPS for a rear wheel hub and bearing assembly. I ended up buying a good quality pattern item for £50!!
Older big SUV's may sound tempting for the price but they can be a total money pit. I bought a 2003 X5 3.0D Sport cheap a few years back. Ended up needing an automatic gearbox and a turbo. Not to mention the last owner had snapped all 6 glowplugs when they attempted removal...
I saw one of these a few days after watching your video, it was down on the driver's side, front and rear, must have been interesting to drive 😬
I like that you used a turbo nozzle on your pressure washer, normally used to clean patios to clean the Audi up.
It was just as bad as a patio 😂
@@SavingSalvage haha 😆
Hi mate...Sweet..Just get it back on the road...
got a similarly priced compressor for my CLS. Worked normally and looked identical to the original