Excellent video. I’ll will try this on my mini Victor oxygen Regulator that just started leaking through the housing weep hole. Thank you for posting this!!
This has nothing to do with this video,sorry, I have a question about venting, My water heater vent is 14 inches wide, will that cause back drafting? My water heater is Bradford white 50 gallon, 3.5 years old, the plumber did not change the vent when he installed the water heater.
the size of the vent pipe is dependent upon how many BTU's per hour the water heater can use and how the vent pipe is run and the length of the vent pipe. The diameter of the water heater is not the correct info to figure that out. But you can start this process by looking at the at the data plate on the water heat to figure out the BTU capacity of the appliance. then you can see what size vent pipe was run and figure out the length of the vent pipe. I do have water heater venting videos on my channel. please check them out.
@@KenTraining f js 40,000btu an hour gas furnace, Gas pressure manifold 4,0(Inwc) Inlet supply supply max 14 0 (Inwc) Inlet Supply Min 5,0 (Inwc) Closet Installation Minimum Clearences 4.front 0 left 12 top, 0 back 0 right 6 vent connector. Category I natural draft ANSI Z21.10'1-2014/CSA 4-1-2014 Pressure: Test 300 psi, Working 150 psi Does not comply w/Juristdiction Having 10ng/
I took several pictures of the vents in attic where it is connected to gas vents and also to. from water heater in closet to the ceiling, but I have forgo tent how to send pictures.
Excellent video. I’ll will try this on my mini Victor oxygen Regulator that just started leaking through the housing weep hole. Thank you for posting this!!
Amazon does not have that kit. Been looking all over. I’ve got the same set up cutskill by Victor.
Very good tutorial, thank you for sharing your outstanding skills. question is it the same kit for acetylene regulater rebuild?
I don't know, I did not do the acetylene regulator...
This has nothing to do with this video,sorry, I have a question about venting, My water heater vent is 14 inches wide, will that cause back drafting? My water heater is Bradford white 50 gallon, 3.5 years old, the plumber did not change the vent when he installed the water heater.
the size of the vent pipe is dependent upon how many BTU's per hour the water heater can use and how the vent pipe is run and the length of the vent pipe. The diameter of the water heater is not the correct info to figure that out. But you can start this process by looking at the at the data plate on the water heat to figure out the BTU capacity of the appliance. then you can see what size vent pipe was run and figure out the length of the vent pipe. I do have water heater venting videos on my channel. please check them out.
@@KenTraining f js 40,000btu an hour gas furnace, Gas pressure manifold 4,0(Inwc)
Inlet supply supply max 14 0 (Inwc)
Inlet Supply Min 5,0 (Inwc)
Closet Installation Minimum Clearences 4.front 0 left 12 top, 0 back 0 right 6 vent connector.
Category I natural draft ANSI Z21.10'1-2014/CSA 4-1-2014
Pressure: Test 300 psi, Working 150 psi Does not comply w/Juristdiction
Having 10ng/
J NOx ReGS
I took several pictures of the vents in attic where it is connected to gas vents and also to. from water heater in closet to the ceiling, but I have forgo tent how to send pictures.
@@yana-tm1ph you can send me a private message with your email address here kentraining.wixsite.com/kentraining/contact
DO you have tutorial to open regulator victor ess4-125-992 oxygen
Sorry, I do not have that video.
$58 currently 🫣