AFAIK: 1. the voltage setting allows you to correct the voltage reported by wheel. E.g. if you measure with your voltometer and find out that your euc is reporting 0.1V more then you can adjust it here. 2. The calibration is useful if for some reason your wheel isn’t flat horizontally when standing still and turned in different directions. Then you enter the calibration, level changes to 1, you place the wheel to “stand perfectly straight”, enter again, level changes to 2 and after a moment the calibration is done.
Hello I have a question, you said not to mess with calibration on the euc but I accidentally did it and now my euc is tilting forward each turn I do. Do you know a way to fix it or I am stuck with it 😅
you'll need to recalerbrate it. go back to the calibration 0, and press it once and it would no longer balance, so you can tilt the EUC around to what you consider leveled and then press the button again and it'll say something like "calibration 1, 2 " and then the wheel will start balancing again. Just do this until you feel satified with the calibration
If you have an extremely accurate voltmeter you can measure the true battery voltage and then check it up against the read out and adjust it if necessary. Otherwise don't mess with it.
Any settings to disable the rear taillight? Sometimes we want to be the literal “unseen ninja in the night” without resorting to removing the device altogether. 😂
Yes but as time went on I learned to control it! I also bought pedal drops that made it a lot easier to ride without wobbles. I’ll post a video soon so stay subscribed!
Yes, keep your back straight and get your ass way behind the wheel and also try to carve a little bit. Keep practicing and you will soon find a braking method where you will have zero wobbles. Also be careful at speed because you can get them there too. Always be turning a little bit. The higher the tire pressure of the more likely you will wobble at speed. You are most prone to it after and acceleration and when you let up and relax a little bit. Also be careful of wobbles when going downhill at speed.
Go to the os tilt back and set the percentage to 70% or higher. Also set the speed till tilt back to a higher number. This video shows me going over all these settings
I have a question mine will only free spin maybe 60 to 62 miles an hour on a full battery and it’s making this weird noise like this running while sitting still is that normal?
Yes that's normal. It is peculiar though. It almost sounds like oil moving around in the suspension. I have a lot of miles on mine and I hear that noise also but it's nothing to worry about.
And as always ppl do, you forgot to show advanced menu settings - enter menu settings, then keep pressing button and enter advanced menu settings. Those what you show, is pretty standard for leaperkim
How can you post a video saying all settings and what the mean, and not know what high speed mode does, ? Don't get me wrong it's not a bad video,.. but how about LYNX and what some settings mean...😂
A settings import/export function would have been useful..
so helpful !! thank you Brian !! 👍
Thanks for the tutorial! 🙏
Thanks just got my ride. Very helpfull.
Thank you so much for this Great job💪🏻🙏🏻😉
AFAIK:
1. the voltage setting allows you to correct the voltage reported by wheel. E.g. if you measure with your voltometer and find out that your euc is reporting 0.1V more then you can adjust it here.
2. The calibration is useful if for some reason your wheel isn’t flat horizontally when standing still and turned in different directions. Then you enter the calibration, level changes to 1, you place the wheel to “stand perfectly straight”, enter again, level changes to 2 and after a moment the calibration is done.
Don't even need to measure with a multimeter, can just check the BMS reported value and then match the display setting to that
Can you do an updated one of this going through all the settings ?
Do you still have these settings or have you changed them if so what are your new settings? Whats the highest safe pwm?
I'm terrified of this wheel😂 the power is insane.
i dont think youre supposed to ride these wheels at limit. the power is a safety margin
Thanks again you are the man
Just trying my best to great quality content! :-)
@@brianonwheels keep it up
Hello I have a question, you said not to mess with calibration on the euc but I accidentally did it and now my euc is tilting forward each turn I do. Do you know a way to fix it or I am stuck with it 😅
you'll need to recalerbrate it. go back to the calibration 0, and press it once and it would no longer balance, so you can tilt the EUC around to what you consider leveled and then press the button again and it'll say something like "calibration 1, 2 " and then the wheel will start balancing again. Just do this until you feel satified with the calibration
lol the info i wanted you dont want to touch it :) about voltage setting, it is hard to find info on leaperkim device
right? I was interested in the voltage settings. i bet you if you went lower voltage you could get much better range.
If you have an extremely accurate voltmeter you can measure the true battery voltage and then check it up against the read out and adjust it if necessary. Otherwise don't mess with it.
Any settings to disable the rear taillight? Sometimes we want to be the literal “unseen ninja in the night” without resorting to removing the device altogether. 😂
Just short press the power button
Thx for the vídeo 👌🏼😉
nice video, thank you!
What settings do you use and why?
Angle point is comming with 40 degree as a default, I didnt change it.Should be 45 or 40 is enough for street ride?
55 is what everyone is suggesting or the wheel will spin out of control
Do you have problems with it wobbling or feeling unstable when you try to break
Yes but as time went on I learned to control it! I also bought pedal drops that made it a lot easier to ride without wobbles. I’ll post a video soon so stay subscribed!
@@brianonwheels ok
Yes, I found that bending my knees a heap to basically get in the seating position behind the wheel helps 👍🏽
Yes, keep your back straight and get your ass way behind the wheel and also try to carve a little bit. Keep practicing and you will soon find a braking method where you will have zero wobbles. Also be careful at speed because you can get them there too. Always be turning a little bit. The higher the tire pressure of the more likely you will wobble at speed. You are most prone to it after and acceleration and when you let up and relax a little bit. Also be careful of wobbles when going downhill at speed.
@@Riceman-o1p thanks
I bought very recently a lynx but I can't go faster than 25km/h. I got the tiltback from 25km/h. Can you help me on that.
Go to the os tilt back and set the percentage to 70% or higher. Also set the speed till tilt back to a higher number. This video shows me going over all these settings
If your power button gets squeaky or gets caught up E wheels will send you a whole new cover. However I solved it with graphite powder.
Can u give us a hint how to do it with graphite powder?
I have a question mine will only free spin maybe 60 to 62 miles an hour on a full battery and it’s making this weird noise like this running while sitting still is that normal?
Yes that's normal. It is peculiar though. It almost sounds like oil moving around in the suspension. I have a lot of miles on mine and I hear that noise also but it's nothing to worry about.
And as always ppl do, you forgot to show advanced menu settings - enter menu settings, then keep pressing button and enter advanced menu settings. Those what you show, is pretty standard for leaperkim
Well get busy and make us a video showing us what the advanced settings can do. I am waiting
@@boblatkey7160 thats what we all need to know, but no one knows. That is point for the toppic - all settings
What are healthy battery cell numbers.
That question is too vague. Please elaborate.
4.2 V/cell @ 100% SOC. 3.2 is about dead.
I use the app for settings.
Thanks. Can I change all that in the mobile application?
some but not all of the settings can be changed in the moblie application
Yes you can, but it depends on what app you're using.
@@familytvbox5218which app do you perfer?
Mine has Er 0bt what does that mean?
there are hiden settings ...do you know to acces them?
👀
Enter the first menu and then long press the same button and that will get you into advanced menu.
How can you post a video saying all settings and what the mean, and not know what high speed mode does, ? Don't get me wrong it's not a bad video,.. but how about LYNX and what some settings mean...😂