2015-2017 Ford F-150/ 2017+ Ford Raptor Transmission Cooler Installation Guide by Mishimoto
Вставка
- Опубліковано 28 сер 2024
- Mishimoto 2015-2017 Ford F-150 / 2017+ Ford Raptor Transmission Cooler: www.mishimoto....
Engineering: www.mishimoto.c...
Facebook: www.mishimoto.c...
Twitter: www.mishimoto.c...
Instagram: www.mishimoto.c...
•Direct fit for all 2015-2017 Ford F-150
•Repositionable design fits both V8 and V6 models
•Tube-and-fin construction for maximum cooling and flow
•184% increase in fluid capacity over stock cooler
•Increases core volume by 105%
•Increases tube surface area by 212% and fin surface area by 132%
•Retains stock hoses for quick and easy installation
•Patent pending
•Mishimoto Lifetime Warranty
Disclaimer
• Please dispose of any liquids properly.
• Allow vehicle to cool completely prior to attempting installation.
• Mishimoto Performance (MP) is not responsible for any vehicle
damage or personal injury due to installation errors, misuse,
or removal of MP products.
• MP always suggests that a trained professional install all
MP products.
• Do not run the engine or drive the vehicle while overheating.
Serious damage may occur.
• Raise vehicle only on jack stands or on a vehicle lift.
Nice walk through , Thank you
Any plans to make a Gen3 raptor bracket for 2021~2023.
Not at this time but stay tuned!
What tool did you use to remove those plastic body clips?
A combination of MMTL-PCPL (Mishimoto Panel Clip Pliers) and MMTL-TRM-11 (Mishimoto Trim Removal Tool Set). Thanks!
How much should I expect to add in fluid for a 2016 5.0 f150 6r80
0.4 Quarts
@@mishimoto directly in the cooler before install?
You can add fluid through the normal process after installation. You do not need to add this to the cooler before installation.
@@mishimoto could it be added to the trans cooler itself though? Long story short previous owner made it not possible through top of trans. Would it be fine adding through trans cooler line or adding to cooler before install?
Yep, but it is suggested to find a way to check the levels.
Does this fit a 2018?
This will fit the following applications:
2015-2017 Ford F-150 w/ 6R80 Transmission
2018+ Ford F-150 w/ 3.3L V6
2017+ Ford F-150 Raptor w/ 3.5L EcoBoost V6
@mishimoto so nothing for the 10R80? I just purchased your intercooler kit and wanted more products. The all aluminum radiator is next.
How much cooler will this transmision cooler be? I tow a full size bass boat I've see temps up to 212 degrees.
There are many variables to consider so we aren't able to provide you with an exact number with your unique situation. However, we would invite you to check out the Engineering blog posts listed within the "Engineering" section on the product page. Thanks!
www.mishimoto.com/engineering/2019/03/ford-f-150-transmission-cooler-2015-2017-rd-pt3/
The transmission fluid/transmissions is these trucks are designed to have 195-200 degrees be the normal operating temperature, so if 212 is the max you are seeing that isn't bad, I occasionally see 210 with my truck empty.
Do you need to drain transmission fluid before changing the transmission cooler?
THe transmission does not need to be drained. The oily fluid that should be lost is what might have been in the lines when removing the old cooler.
Sounds good. Didn't know if there was any residual fluid or if the whole system was full. Thanks for the reply.
so do I need to add any transmission fluid??
@@UAE111 Good question, we need an answer!
Do we need to add transmission fluid?