You wired the relay output side wrong. You show mains nutrual and hot going to the relay out side that is not correct wiring. The SSR input side is correct and the thermo couple is correct.
While you're correct, it shouldn't matter with AC. It may cause issues if it's the pseudo-AC you get from inverters, but with mains it won't make a difference.
تبارك الله عليك اخويا ، و المغاربة اللي تيهضرو بالانجليزية و شرحو بالانجليزية ، مثال بسيط و مشجع بالتفيق اخويا ، و لكن الاجليزية عندك كازوية هههههه تبرك الله عليك برو ،😍😍
Bravo et merci pour ton travail . STP Possible avec ce REX C100 , de faire des paliers d'arrêt de chauffe avant d'atteindre des hautes temperatures ? , Merci de tes réponses
Normally PID parameters are default, but you can set the action frequency to control the PID action speed to realize the more precise temperature control, and for the output we recommend the SSR instead of the contactor.
Hello, if you want to set the cooling mode or just want the thermocouple to detect temperaturer below zero? 1. You can set the cooling mode. 2. If you want to detect subzero, you can replace the thermocouple with PT100, it can detect the temperature range from -200℃~400℃，just need to set the controller input into PT100, then it will work.
Anyone see these behave strangely with the PV value jumping all over as soon as the SSR starts cycling? I’ve tried several thermocouples and two different c100 controllers. The heating element can be plugged in or disconnected and the behavior continues.
Hola, podemos usarlo en el sistema de nebulización o el llamado sistema de niebla que se encuentra en los cafés para enfriar el ambiente cuando la temperatura es alta, siempre que funcione durante treinta segundos y se corte diez segundos, luego funcione treinta segundos y se corta diez segundos y permanece así hasta que baja la temperatura y se apaga automáticamente. Gracias
@@chihanecreativetechno7604 Muchas gracias señor. Estaría muy feliz si pudieras explicar cómo configurarlo de esta manera. Y tienes todo mi respeto y aprecio .
Hola, puede conectar el relé de tiempo al Controlador de temperatura, con funciones de trabajo de tiempo de ciclo como dh48s - s, que pueden funcionar durante 30 segundos y detenerse durante 10 segundos.
It appear like this “UUU” is says in the manual it is underscale error,where should i start to trace the problem? Please make a video on how to fix this problem
@@user-CzK thanks for ur question im gonna get back to as soon as possible after geting more knowledge about this matter hope this is helpful to u and get back to u as as possible .have a great day jayel
Gudday sir. How about i will use for cooling sir, all i need is 16-17 C means, 16C below it will turn-off and if 17C up it will turn-on. I will use as a switch(i will pluge my refrigerator) for restoring my pig semen. Thank u and God bles
Hi there if you wanna use it you need to do this : _press set ,the buttom sv blinks _with arrows up down you need to ajust your desire temperature 16c or 17c . _once yoù have done so press (set) once to store it. _now you need to press hold the (set) button and the button next to it for 3 seconds ,Cod appears and the buttom figures (sv) blinking. So now you need to make it 0001 and after that press (set) four times until you see (oud) appears ,now if you have 000 below (oud) you need to change with arrows up down to 001 for cooling and after that hold press the set button for approximately 3 second and let go .now your device is programed to your desired temperature .hope this could help if u have any doubt please feel free to contact me .thanks
You wired the relay output side wrong. You show mains nutrual and hot going to the relay out side that is not correct wiring. The SSR input side is correct and the thermo couple is correct.
While you're correct, it shouldn't matter with AC. It may cause issues if it's the pseudo-AC you get from inverters, but with mains it won't make a difference.
I can't even hear what you are saying over the background music.
I’m trying to use this PID for a heater element. I’m not sure if my settings are wrong or if my controller is bad. I can’t get it to go over 200F
تبارك الله عليك اخويا ، و المغاربة اللي تيهضرو بالانجليزية و شرحو بالانجليزية ، مثال بسيط و مشجع بالتفيق اخويا ، و لكن الاجليزية عندك كازوية هههههه تبرك الله عليك برو ،😍😍
Bravo et merci pour ton travail . STP Possible avec ce REX C100 , de faire des paliers d'arrêt de chauffe avant d'atteindre des hautes temperatures ? , Merci de tes réponses
as tu trouvé la solution pour les paliers ?
Que significa que me aparezca STOP en la parte verde?
Is it still possible to combine the fan and the heater in parallel?
Other the ssr u can
How to input PID parameters?
Normally PID parameters are default, but you can set the action frequency to control the PID action speed to realize the more precise temperature control, and for the output we recommend the SSR instead of the contactor.
Hi. Can we replace the thermocouple with coolant temperature sensor?
Hello, if you want to set the cooling mode or just want the thermocouple to detect temperaturer below zero? 1. You can set the cooling mode. 2. If you want to detect subzero, you can replace the thermocouple with PT100, it can detect the temperature range from -200℃~400℃，just need to set the controller input into PT100, then it will work.
ما شاء الله وبالتوفيق
ربي يحفظك
@@chihanecreativetechno7604 أجمعين يااااااااارب. اوا دخل العربية في الشرح
Anyone see these behave strangely with the PV value jumping all over as soon as the SSR starts cycling? I’ve tried several thermocouples and two different c100 controllers. The heating element can be plugged in or disconnected and the behavior continues.
Same here. Did you get the solution? I'm struggling with this
I never found a solution with the counterfeit Rex controllers. Most of these are fakes made in China. Authentic versions are produced in Japan.
gaarbaage
very practical thanks
Hola, podemos usarlo en el sistema de nebulización o el llamado sistema de niebla que se encuentra en los cafés para enfriar el ambiente cuando la temperatura es alta, siempre que funcione durante treinta segundos y se corte diez segundos, luego funcione treinta segundos y se corta diez segundos y permanece así hasta que baja la temperatura y se apaga automáticamente. Gracias
Hola . claro que si puede usar in esso tipo de sistemas .espero que va bien para usted .muchas gracias
@@chihanecreativetechno7604 Muchas gracias señor. Estaría muy feliz si pudieras explicar cómo configurarlo de esta manera. Y tienes todo mi respeto y aprecio .
Hola, puede conectar el relé de tiempo al Controlador de temperatura, con funciones de trabajo de tiempo de ciclo como dh48s - s, que pueden funcionar durante 30 segundos y detenerse durante 10 segundos.
Very good
omg the background music is way to loud sorry i have to move on.
i like this devise
Hello . Do you know how to fix underscale?
Hi sorry don't understand this could u explain more ? Thanks
It appear like this “UUU” is says in the manual it is underscale error,where should i start to trace the problem? Please make a video on how to fix this problem
@@user-CzK thanks for ur question im gonna get back to as soon as possible after geting more knowledge about this matter hope this is helpful to u and get back to u as as possible .have a great day jayel
@@user-CzK The problem may be due to the type of thermocouple is wrong for your device.
May I know the name/type of cable to connect between the module?
ريحة عرب والله اعلم
Gudday sir. How about i will use for cooling sir, all i need is 16-17 C means, 16C below it will turn-off and if 17C up it will turn-on. I will use as a switch(i will pluge my refrigerator) for restoring my pig semen. Thank u and God bles
Hi there if you wanna use it you need to do this :
_press set ,the buttom sv blinks
_with arrows up down you need to ajust your desire temperature 16c or 17c .
_once yoù have done so press (set) once to store it.
_now you need to press hold the (set) button and the button next to it for 3 seconds ,Cod appears and the buttom figures (sv) blinking. So now you need to make it 0001 and after that press (set) four times until you see (oud) appears ,now if you have 000 below (oud) you need to change with arrows up down to 001 for cooling and after that hold press the set button for approximately 3 second and let go .now your device is programed to your desired temperature .hope this could help if u have any doubt please feel free to contact me .thanks
@@chihanecreativetechno7604 wow thank you very much sir, this will help a lot, God bless
Can l use this on incubator please
Hi yes u can use for incubator
@@chihanecreativetechno7604 but how sir plz explain the settings.... I need keep 37 °c in box?
Very poor video. Thanks for wasting everyones time.
You should learn first then show to others. No offence this is just suggestion.
Thsnks
You are mad
Music is not at all helpful.
Can I use this for 2000 Watt heating for an oven?