I really appreciate more than just the kit, but also the fact that you guys explain the ramifications of the kit, with things like emissions and what may go with it.
@@BTRcarcustoms i have a gt3071r but it has a 5 bolt internally wastegated turbine housing. Where can i get the turbine housing you all offered in this kit?
Im currently running this manifold with the tomei mx7960 turbo on my fully built motor bk2 2.0t. But i do plan on switching to this turbo for more power!
On an honest note, would you recommend going with this turbo kit or going with Tim's BT-400 Turbo Kit? I'm a bk2 already tuned on your stage 2 tune. Also, with this turbo kit is it recommended that you get the upgraded oem injectors as well? Any other supporting mods for a stock engine such as fuel pump, etc?
Hello I am thinking of buying this kit for my bk2 2.0t auto and I have some questions regarding it. Does it use an external waste gate? And do I need a aftermarket intercooler to hit 400whp. And is the gen 2 3071r a better option for the auto?
@@BTRcarcustoms thanks for the quick reply, I’m looking at buying a car that has this exact set up and I was wondering if with the boost controller it could be turned down just a little to increase longevity. I follow many genesis coupe fb pages and I see a lot of people needing new engines. (Not tuned by you or this kit)
I have a tuned BK2 that has 300whp all I’ve done to it is ecu tune with down pipe and intake. I just bought my E85 kit and a upgraded front mount intercooler and a ported throttle body. I want to buy these kit but kinda scared that I might just be a little over the 400hp. What would be the best option??
Hey I have a 2014 2.0 r spec wondering what will I have to do to run a bov since without one the Ecu will just cut boost exponentially? Thanks in advance
Hi! does that kit come with a oil restrictor? i heard you need that once u go for a ball bearing turbo else you end upp with lots of oil in your CAI/intercooler.
manual transmissions have less power loss through the drivetrain and have the ability to rev out higher than automatics in general so more power to the ground and wider powerband
Well I’m order for the tune to even work in the first place I would just recommend a aftermarket intake then the tune then the turbo kit. I think it’s tuned to be compatible with the alfaspeed tune but I’m not sure.
Sorry if this is a noob question but how does one go about getting a tune once installed? Is the car drivable at all once swapped? Do I need to find transport to a shop that can tune it or something?
@@BTRcarcustoms with that being said, would it be wise to throw in some 1000cc injectors with this kit? I'm on the oem ecu and getting a tune after installment.
Hope I get a response back! So you’re saying that my bk1 2.0t that has a isr race catbaxk exhaust with my cat gutted out, k&n cold air intake, and BOV. i can take the GT3076R with the step colder plugs, and boost controller, with stock intercooler, stock injectors, fuel pump etc slap the turbo kit you’re selling in and get a tune and run 370-380whp just fine? If so you’re guaranteed a sale for one of those beginning of next year for sure!!!
on a bk1 you need injectors and highly recommend doing an intercooler upgrade. 3076R can safely do 350whp on the manual bk1 at around 20psi, some have pushed to 21-22psi and gotten 370+whp as well but our recommendation would be 20psi for the bk1
Im thinking to switch to this set up soon currently running stuffed turbo on E85 (bk2 2013 AT 165,000 miles) what do you recommend me to do with the engine before I put this kit? I dont wanna blow the engine to fast
Hi Pete Atp unfortunately discontinued the turbo so we had to switch brands Use this link www.shopbtr.com/350-500-horsepower-turbo-kit-for-2010-2014-Hyundai-Genesis-Coupe-20T_p_6427.html
What kit would you say is best for hitting around 380whp without e85 as in Canada it’s not really available around me. There were 2 kits I was looking at this one in the video and the Tomei mx7960 unless there is another you recommend.
I have 2012 genesis coupe 2.0t. The turbo just went bad and have to replace one. I drive a lot everyday. Everything in the car is stock. Which one do you recommend? I went your website and got confused. I drive around 90 miles everyday.
So question what size/model would I need to buy for a 2011 2.0t manual if I’m trying to get the most hp outta it? And would I have to tune it immediately after installation?
When I go on the website for this I choose the 2013-14 turbo it asks me if I have a bk1 manifold and it asks me if I have a bk1 o2 housing yet I have a bk2 what option do I pick
I am having the same issue, do I need to go and buy a bk1 o2 housing for my bk2 in order to install since you guys don’t supply an o2 housing? If so that is very inconvenient for bk2 owners. Please let me know if I need to buy additional parts such as a bk1 o2 housing.
@@ologyzyt3733 yes bk1 o2 housing or bk1 primary cat Only reason we don’t offer it is because many companies are discontinuing o2 housings due to regulations.
@@BTRcarcustoms I’ll be going with a gtx, wiseco pistons, k1 rods, rebalanced crank, arp head and mains. Apart from that I’m already using the mishimoto race intercooler, full 3inch exhaust turbo back with a haltech ecu
The auto transmission in the bk1 (2010-12) is unfortunately the worst transmission in the genesis coupe. It slips too much and eats up a lot of power. 400 whp is going to be nearly impossible keeping that transmission. Highest we’ve seen with that particular transmission was 330 whp.
@justinsilvia2925 it's a lot of work bro and honestly not worth it, since it has 3 more additional gear it will cause some confusion to the ECU. Your best bet is to go manuel swap but then again that's a pain in the ass because you will need manuel wire harness and ecu for that. It's not worth it bro
@@justinsilvia2925 oh snap that's so kool contrulations, make sure you change the line properly, use fresh washers and the side or else there will be an oil leak from the top feed line
I'm in the market to purchase ASAP I have a 2013 bk2 2.0 rspec manual I'm currently tuned and have a full turbo back exhaust from stock turbo I want to upgrade my turbo wanna be making 400 without switching fuel systems which turbo do you recommend for me and do I have to buy a bk1 o2 housing I don't care about passing emissions
For any type of power upgrade on high mileage cars, have the car looked over with compression test to make sure engine is healthy before doing modifications
I really appreciate more than just the kit, but also the fact that you guys explain the ramifications of the kit, with things like emissions and what may go with it.
thank you! we try to cover all bases!
@@BTRcarcustoms what city are you located?
@@BTRcarcustoms i have a gt3071r but it has a 5 bolt internally wastegated turbine housing. Where can i get the turbine housing you all offered in this kit?
I need a genesis now. I currently have a 07 tiburon
Got one for sale
Got a 06 SE and I want a gen so bad
Good video guys! I like that when you order this kit it comes preassembled 👍
Yes that is definitely a plus and makes install so much easier
I just ordered mines yay!!
1900$
The best the best of the best and performance part i never see super professional thanks for you video and never regret about my genesis
Im currently running this manifold with the tomei mx7960 turbo on my fully built motor bk2 2.0t. But i do plan on switching to this turbo for more power!
MO POWA baby!
Great video and one hell of a setup 👌. Can you recommend a turbo blanket for that exact turbine housing?
We’ve used T3 ones for it before and its a tight fit. T4 one might fit as well but with some slack
Let me know if youre gona sell ur stuffed turbo LOL 😛
On an honest note, would you recommend going with this turbo kit or going with Tim's BT-400 Turbo Kit? I'm a bk2 already tuned on your stage 2 tune.
Also, with this turbo kit is it recommended that you get the upgraded oem injectors as well? Any other supporting mods for a stock engine such as fuel pump, etc?
You dont need any fuel upgrades to run this kit on a bk2. We cannot comment on a kit we do not sell but our kit works as advertised
@@BTRcarcustoms Awesome! Thank you for the quick response.
That’s a big spinny boi
I can’t find 3076r on the website
Since this got replace bye Arashi, what do you recommend for a 2010 bk1 2.0t for a drop in turbo with stock cat and stock engine to be safety run?
I wish you guys were located in San Bernardino ca lol
Hello I am thinking of buying this kit for my bk2 2.0t auto and I have some questions regarding it. Does it use an external waste gate? And do I need a aftermarket intercooler to hit 400whp. And is the gen 2 3071r a better option for the auto?
it uses an internal wastegate. as for 400 whp it may be possible if coupled with a TCU tune to raise the rev range further.
I need that kit for me Genesis 2011 2.0T.
Suggestions for building up the motor just to make it more reliable for bk2 with this kit, as it will be my daily.
This kit is super reliable on stock engine at 22-23 psi for the bk2
@@BTRcarcustoms thanks for the quick reply, I’m looking at buying a car that has this exact set up and I was wondering if with the boost controller it could be turned down just a little to increase longevity. I follow many genesis coupe fb pages and I see a lot of people needing new engines. (Not tuned by you or this kit)
I have a tuned BK2 that has 300whp all I’ve done to it is ecu tune with down pipe and intake. I just bought my E85 kit and a upgraded front mount intercooler and a ported throttle body. I want to buy these kit but kinda scared that I might just be a little over the 400hp. What would be the best option??
Stock block manual transmission, we recommend using the gt(x)3071r or gt(x)3076r
Hey I have a 2014 2.0 r spec wondering what will I have to do to run a bov since without one the Ecu will just cut boost exponentially? Thanks in advance
There are many different bov options on our site.
@@BTRcarcustoms thank you man
I have already purchased the mxp header.. is this header shown in video made specific for this turbo?
Hi! does that kit come with a oil restrictor? i heard you need that once u go for a ball bearing turbo else you end upp with lots of oil in your CAI/intercooler.
Yes sir oil restrictor is installed during our assembly process
@@BTRcarcustoms thx for a fast answer :)
can you do some videos on the best mods and just overall videos on the 3.8 genesis
Yes! more videos to come and we'll pick out some parts for the 3.8 guys too!
@@BTRcarcustoms thank you so much
@@jrtheop5750 it is our pleasure!
Does this work with a tuned engine
Why does the manual bk2 have a higher output than the automatic and why do you recommend a smaller turbo size for the automatic ?
manual transmissions have less power loss through the drivetrain and have the ability to rev out higher than automatics in general so more power to the ground and wider powerband
I have a 2013, fully stock beside exhaust, to do this kit do I need any other supporting mods? Besides a tune
Well I’m order for the tune to even work in the first place I would just recommend a aftermarket intake then the tune then the turbo kit. I think it’s tuned to be compatible with the alfaspeed tune but I’m not sure.
i still have stock bk2 cat behind the turbo the rest is straight pipe and stock bk2 manifold would i need to swap for bk1 o2 and manifold?
That is correct :)
Can this kit be used with oem ecu with alphaspeed tune? Or do i need aftermarket ecu like haltech?
yes it's tuned all the time on oem ECU
Sorry if this is a noob question but how does one go about getting a tune once installed? Is the car drivable at all once swapped? Do I need to find transport to a shop that can tune it or something?
You can search for the nearest Alphaspeed dealer to have the car tuned
2011 power 2.0t is poor turbo power how poor auto? How much hp?
If my goals is 400whp or higher on a 2.0t automatic would I be better to go with the GT3076R?? On the stock block
stock block is going to be hard to reach 400 whp with the automatic on the stock block due to high drivetrain loss
@@BTRcarcustoms yeah but would it be possible with e85, fbo water meth and one of those turbos?
Just ordered this kit last week for my BK2 Auto but apparently the 3071 was discontinued and you guys have to source a different turbo🥲
Yes we were blindsided with the discontinuation of the turbos from ATP. We will source a good replacement very soon
@@BTRcarcustoms with that being said, would it be wise to throw in some 1000cc injectors with this kit? I'm on the oem ecu and getting a tune after installment.
Hope I get a response back! So you’re saying that my bk1 2.0t that has a isr race catbaxk exhaust with my cat gutted out, k&n cold air intake, and BOV. i can take the GT3076R with the step colder plugs, and boost controller, with stock intercooler, stock injectors, fuel pump etc slap the turbo kit you’re selling in and get a tune and run 370-380whp just fine? If so you’re guaranteed a sale for one of those beginning of next year for sure!!!
I’m gonna assume a aftermarket intercooler would make it a lot more safe because of the less restriction it would cause
on a bk1 you need injectors and highly recommend doing an intercooler upgrade. 3076R can safely do 350whp on the manual bk1 at around 20psi, some have pushed to 21-22psi and gotten 370+whp as well but our recommendation would be 20psi for the bk1
@@BTRcarcustoms In the place i live in canada we dont have e85 how much do you think id push on 91 octane?
@@CanadianLag the power figures given on the video is for 93. for 91 you can expect around 10 whp less
Im thinking to switch to this set up soon
currently running stuffed turbo on E85 (bk2 2013 AT 165,000 miles) what do you recommend me to do with the engine before I put this kit? I dont wanna blow the engine to fast
Do a compression test to make sure the engine is healthy :)
Do you recall how much power your genesis was making on that setup?
the link listed in the bio doesn't redirect. can you send a link to shop this kit?
Hi Pete
Atp unfortunately discontinued the turbo so we had to switch brands
Use this link
www.shopbtr.com/350-500-horsepower-turbo-kit-for-2010-2014-Hyundai-Genesis-Coupe-20T_p_6427.html
@@BTRcarcustoms see my other question on your other vid. Thx for the response
What kit would you say is best for hitting around 380whp without e85 as in Canada it’s not really available around me. There were 2 kits I was looking at this one in the video and the Tomei mx7960 unless there is another you recommend.
Gt3076r or gtx3076r would be your best bet
When I goto purchase the kit what turbo option do I choose the initial one is the gt28s something like that I have a bk1 2.0t
Turbo choice is completely up to you. Sam does explain the few we recommend in the video
@@BTRcarcustoms oh okay so the one in the video is good for the swap got it
what aftermarket mods would be needed to make run the turbo safely?
Intake and 3” exhaust for 2013-14
Add injectors and front mount intercooler for 2010-12
@@BTRcarcustoms thank you!
I have an after marketer 02 housing for a 2013 is that okay?
This kit has been replaced by another kit and it requires a bk1 style housing
ua-cam.com/video/UfbxgI6cG8A/v-deo.html
will this turbo be okay, with stock internals on a bk1 turbo
Yes but this kit is discontinued and a new kit has replaced it. Please follow the link in the description
I have 2012 genesis coupe 2.0t. The turbo just went bad and have to replace one. I drive a lot everyday. Everything in the car is stock. Which one do you recommend? I went your website and got confused. I drive around 90 miles everyday.
Check out the latest video about Arashi Turbo kit
What size AR housing was the bk2 manual running on the 3071 and 3076?
These turbos are all 0.72 a/r according to ATP
@@BTRcarcustoms thank you
If I get the Arashi TD06SL2-AR3 BB (500hp) [+$209.00] do I need to tune the ecu or plug and play do u guys recommend getting a tune ecu?
You 100% need a tune
@@BTRcarcustoms any recommendations? On tune
Can you run this turbo without a tune for a bit or do you need a tune right after you put it on?
Tune required
On a bk2 can the electronic wastegate actuator be mounted to this turbo setup. Sorry im new
No, it uses a pneumatic wastegate as shown on the turbo
you can just unplug the bk2 oem wastegate and the tuner can just tune that out :) simple!
Cool. Thanks.
So question what size/model would I need to buy for a 2011 2.0t manual if I’m trying to get the most hp outta it? And would I have to tune it immediately after installation?
if manual GT3076 is a good size, if automatic GT28 is a good size
@@BTRcarcustoms yeah I got manual transmission thanks, finna order one in the near future
Would I need to tune it and if so what tune do you recommend??
All turbo upgrades require a custom
ecu tune
When I go on the website for this I choose the 2013-14 turbo it asks me if I have a bk1 manifold and it asks me if I have a bk1 o2 housing yet I have a bk2 what option do I pick
Bk1 housing and bk1 manifold is what you need to source to run this turbo even if you have a bk2
I am having the same issue, do I need to go and buy a bk1 o2 housing for my bk2 in order to install since you guys don’t supply an o2 housing? If so that is very inconvenient for bk2 owners. Please let me know if I need to buy additional parts such as a bk1 o2 housing.
@@ologyzyt3733 yes bk1 o2 housing or bk1 primary cat
Only reason we don’t offer it is because many companies are discontinuing o2 housings due to regulations.
How much is the gen 2 3076r capable of making with a fully built bottom? (sleeved, pistons and rods)
450-500 whp is possible with a built bottom end depending on if you are using the GT or GTX
@@BTRcarcustoms I’ll be going with a gtx, wiseco pistons, k1 rods, rebalanced crank, arp head and mains. Apart from that I’m already using the mishimoto race intercooler, full 3inch exhaust turbo back with a haltech ecu
I cant find one to fit my 2013 BK2 2.0t can you please refer me to an outlet.
The link to the kit is in the description
Hi I have a 2011 2.0t auto Matic looking for 400 plus hp how do I achieve that built engine and
do I hav e to do any upgrades to the transmission?
The auto transmission in the bk1 (2010-12) is unfortunately the worst transmission in the genesis coupe. It slips too much and eats up a lot of power.
400 whp is going to be nearly impossible keeping that transmission. Highest we’ve seen with that particular transmission was 330 whp.
Am I able to swap the 8 speed from the bk2
@justinsilvia2925 it's a lot of work bro and honestly not worth it, since it has 3 more additional gear it will cause some confusion to the ECU. Your best bet is to go manuel swap but then again that's a pain in the ass because you will need manuel wire harness and ecu for that. It's not worth it bro
@@josemolina3858 yea realized that haha I’m replacing the oil line to the turbo rn gonna get a 5.0 soon
@@justinsilvia2925 oh snap that's so kool contrulations, make sure you change the line properly, use fresh washers and the side or else there will be an oil leak from the top feed line
Do you ship to Toronto Canada
@@dennismhein yes you can order parts to ship to Canada right from our site
Wait if your engine is stock can i just stick this turbo kit in it or do I need anything else
we recommend doing a good exhaust setup and a tune :)
What can I do to my automatic transmission to allow it to handle more hp?
Level10 makes some parts for the bk1 autos but at the end of the day it will never so what the manuals can
For huyndai genesis 2010 2.0t bk 1 auto wich one should get
3071R with e85 has shown some good results on the bk1 2.0T auto lately
Thk you
What kind of power is the gtx2867r on 93 octane making?
depends on the trans but those turbos will do around 350 whp on the manuals
Bk1 auto I need a list of mods to keep her reliable and at around 250😔
for 250whp, you would be best to use the GT28 size turbo with 750cc injectors
I'm in the market to purchase ASAP I have a 2013 bk2 2.0 rspec manual I'm currently tuned and have a full turbo back exhaust from stock turbo I want to upgrade my turbo wanna be making 400 without switching fuel systems which turbo do you recommend for me and do I have to buy a bk1 o2 housing I don't care about passing emissions
3071 or 3076 would be good. And yes bk1 style o2 housing is needed
i have a bk2 2.0t 8speed auto. is the dyno graph for the auto bk2 for 6 speed or 8 speed?
The video explains the power difference between auto and manual.
The Automatic BK2's only come in an 8speed ..
@@Cell-kh1rs yeah, I found that out a week after my post. Definitely felt dumb lol. Thanks though.
do you recommend a tune and stage 2 clutch (bk1)
Tune is a requirement and clutch most likely will need to be upgraded
@@BTRcarcustoms thanks so much for the reply
I want this
Can this kit be ran with the oem bk1 intercooler ?
Yes but intercooler will become a restriction to flow past a certain power level. For example, on BK2 the OEM intercooler is no good after 400ish whp
by any chance are you guys still selling this turbo?
This kit has been superseded by this
500 HP Genesis Coupe 2.0T Drop In Turbo Kit (Details and Assembly)
ua-cam.com/video/UfbxgI6cG8A/v-deo.html
How much hp does it make with the cat still on? I can't really take mine off just curious
Expect a catted car to make around 10hp less than those without cats
@@BTRcarcustoms Whats the stock size of the 2014 genesis coupe 2.0T turbo? I can't find info anywhere
@@MJT-DA td04-14t.. belongs on a lawnmower not a car
@@BTRcarcustoms haha trust me i know I plan to upgrade after the car is paid off
Do you need the boost controller with this?
yes you do
How do I find to order 🤔
This item has been replaced with Arashi Turbo kit. Link is in the description
Hey guy,do you do top mounts,I really would love that???
www.shopbtr.com/CX-Racing-Top-Mount-T3-Turbo-Manifold-For-10-14-Hyundai-Genesis-Coupe-20T_p_7343.html
Thanks,but there's some bad reviews for that brand 😔
@@gabymaldo2424 unfortunately so due to bad craftsmanship of the manifold
I think I'll go with your kit,i got a BK1,what would you recommend??
@@gabymaldo2424 for bk1 3071 or 3076 for manuals gt28 for automatic
How long will it take to ship to texas
Normal assembly time is around 2 weeks
Where can I get those copper nuts?
let us know the thread pitch you need and we can source them for you
I appreciate it!
How i get that kit?
Link is in the descriptions. The turbo kit has been succeeded by the 350-500 turbo kit
Can you put together a list of everything needed to throw this on a bk2 2.0t without a built motor , going to order from you sometime this week
all you need is intake and 3" exhaust with the spark plugs, boost controller and a custom tune
Can stock bk1 rods handle ~370hp?
yes it can, just need to make sure your engine is in good condition beforehand :)
@@BTRcarcustoms what size recommendaiton for a BK1 auto
What supporting mods would you need to do for this as well?
full exhaust and a nice intercooler would do :) if its a bk1 you will need injectors too
Is it carb legal
no there isn't a carb approval for this
but most states that do obd testing for emissions, you can pass that if you use oem bk1 primary cat
Good thing I live in Florida lol
What is your guys email, very interested and do you guys offer miltary discounts by chance?
please email support@bloodtyperacing.com
So I can run this on a stock motor bk2 with 125k? I daily it. Don’t push it hard Don’t wanna blow my engine. Is it safe?
For any type of power upgrade on high mileage cars, have the car looked over with compression test to make sure engine is healthy before doing modifications
@@BTRcarcustoms thank you. What type of shop would do that test?
@@bk2_sadie368 any mechanic should be able to perform a compression test
1st
🧑🦯
Would this Work on the 2012 2.0T Sonata?