How To Replace Inside interior Door Opener Handle Levers on A Jeep TJ YJ 89-2006
Вставка
- Опубліковано 24 кві 2018
- Buy interior door handles here:
amzn.to/3qQ0WJi
The whole parts list I use on my Overland rig
www.amazon.com/shop/atemoffroad
More Awesome Content?
DIY Overland kitchen Tailgate table
• DIY Jeep Wrangler Tj ...
DIY Bolt On Hi-Lift J-Mount Install
• Video
DIY Front Stubby off-road bumper
• Jeep Wrangler TJ - DIY...
DIY Body Lift
• Jeep Wrangler TJ - DIY...
Jeep front and rear shock replacement
• DIY How To Replace All...
Sway bar quick disconnects
• $20 DIY Jeep Sway Bar ...
Overland Tool mounting Solutions
• DIY Overland Trail Car...
Jeep Tailgate table build
• DIY Jeep Wrangler TJ T...
DIY Jeep Rock sliders
• DIY Jeep Wrangler Rock...
How To Install cb radio in Jeep Wrangler
• How To Properly Instal...
32” tires I’m running
• 32” Tires On My Jeep W...
DIY On board air compressor build
• Jeep Wrangler Tj | Lj ...
Fuel and water cell mounting Solutions
• DIY Overland Jeep Wran...
DIY Rear Trail Cargo Rack build
• Jeep Wrangler- DIY Ove...
Hi jack hood mounts install
• Jeep Wrangler How To I...
Wireless winch controls
• How To Install An Opti...
DIY Jeep E Fan build
• DIY JEEP WRANGLER Elec...
#jeeptj #interiordoorhandle #doorhandle
Good working door handle is vital when needing to get out of your jeep and your safety. In this Short video I tell a story how I replace my jeeps inside door handle. Also what to look out for when making this repair and where to get the parts. I hope you enjoy.. Thanks for watching! And if you haven't yet subscribed, DO IT!! Also hit the bell for awesome notifications.
DIY how to replace Jeep TJ YJ interior inside door handle!! Thanks for watching
DISCLAIMER
Due to the factors out of control by ATEM OFFROAD, we cannot guarantee against improper use or unauthorized modifications of this information ATEM OFFROAD assumes no liability or responsibility for property damages or injuries incurred as a result of any information contained in this video. Use this information at your own risk . ATEM OFFROAD recommends safe practices when working on vehicles and or with tools seen in this video, any injury damage or loss that may result from improper use of these tools equipment or from the information contained in this video
Is the sole responsibility of the user and not ATEM OFFROAD. Be Safe
This video and description contains affiliate links which means if you click on one of these product links, I’ll receive a small commission. - Авто та транспорт
![Lp. Последняя Реальность #107 РОДНОЙ ДОМ [Финал] • Майнкрафт](http://i.ytimg.com/vi/IK3QKzKUlHM/mqdefault.jpg)
This told me exactly what to do,I watched another video, a young boy did it without removing the door panel.it seemed a lot harder.thank you alot
Thanks for watching
Thanks to this video I was able to fix my door latch with half an hour, thank you!
Thanks for this. Your video is the best ive come across for this fix.
Waun M thank you, I appreciate it!
Thanks bud
Great video. I am heading out to replace my driver's side handle on my 97 TJ. The screw is okay. The spring around the latch has popped out and the latch will no longer open the door. I have to roll down the window and reach outside to get out. Lol If it was just the screw, I think I would have just used a washer and a longer screw for a few months.
Thanks for watching
Good job bro but I think that’s for the drivers side. When locked the button should be pushed in not out.
Jesus Avila haha I happened to notice that t00, you can tell at the end of the video, but actually it is the right one for the right side. there was a manufacturer defect on the pair of handles I have. This pair has the “Lock” label on the wrong side of the push lock lever. Thank for watching..
I have gone through more than a few of these door handles. The weak link has always been one of those clips that snap over the rod. Someone told me they found "metal" clips for theirs. Here I am looking and learning. If anyone knows where to get the metal ones, I'd appreciate hearing. Also, the latest handles I got off ebay, the holes were too small for the rod. I had to drill them out, and now they are so thin they are sure to break in this AZ summer. 95 YJ.
Looks like you have an aftermarket keyless entry system in the door. If so, can you explain how you mounted that system inside your half door?
Wow 😧 thanks so easier than the other videos I looked at without removing the door great man thank you
Thanks for watching
To the point and very helpful. It's my first Jeep. Thanks. btw, the screw is missing - just get a t15 screw 1/2" long?
Thank you
haha I happened to notice that t00, you can tell at the end of the video, but actually it is the right one for the right side. there was a manufacturer defect on the pair of handles I have. This pair has the “Lock” label on the wrong side of the push lock lever. Thank for watching..
hi question, which rod goes on top hole of latch and which rod goes on bottom hole of latch when replacing . do they Chris cross or no ?
Where did you buy the part at?
mike whitecotton eBay
Had my boyfriend do this for me. He put the bars on the opposite clips and bent the rods. I've been trying to fix it. Now the door won't open even with the rods in the correct location. What do I do? Other than keep him away from my beloved Jeep!
@Sheelah Casson 💥 nice, thanks for watching ! Ooh wow that’s a bummer, is the door stuck and won’t open at all? Half door , full door? I would try to use the key and open the door from the outside, those doors are made to be removed, maybe able to remove the hinge bolts and pull the door off that way to be repaired, other than that last resort is to break the door panel on the inside, to get to the door latch to repair or replace and open door!, I’m just thinking off the top , honestly id have to be there to really see what’s going on
I have to do this on my 97 Jeep Wrangler sport. Anymore tricks I should know before I get started? Should I get the parts from the dealer or Napa, etc?
Lee Sires no it’s pretty straight forward, I bought the replacements handles on eBay or amazon
@@ATEMOFFROAD works great, thank you for sharing!