Pro tip for the fuel filter replacement. Lossen the 3 7/16 cap bolts but do not remove them. Do not disconnect any of the fuel lines. Instead, leave everyting on including the clamp bolt. From inside the vehicle while sitting in the drivers seat, remove the 2 7/16 bolts that hold the fuel filter bracket. Fuel filter with housing is now easier to move around to remove the 3 cap bolts to service the filters (green screen and molded paper filter). Clear the drain line. Clean the inside and fill halfway up with fuel and install new filters then the cap with a new o-ring. Place the oring in a zip loc bag and put it in the freezer overnight to shrink it. To prime, loosen the stainless steel screw at the top. Crank until only fuel comes out (no bubbles). Start and run the engine. Check for leaks then install into firewall by using an awl to center one of the bolt holes and install a bolt into the other. Tighten both once started. You're done.
CDR valve serice pro tip. So you dont drop that bottom clamp after you loosen it. Place a small zip tie under it so it doesn't slide down once it's loose.
I just bought a Humvee from GovPlanet, and its report says the motor doesn’t run. So, now I must binge watch your project vids so I’m better prepared for when it arrives. Thanks for documenting it all.
Great information, it makes sense to change the filter for better air intake. Those original ones looks like designed for desert. Would have been great to know how it drives before and after.
I just installed my PCV valve. ( I thought it called the CDR valve ) whatever it called it stopped the smoke from oil filler which I thought was blow by. So glad that You started another project. Every video lerned something from you. Thanks for sharing.
Love your videos. I just won my Humvee last week . Now the wait time for release. Meanwhile I watch your videos . Can you add links to the parts you install on the videos ?
Do you have an update video or picture of how much you cut out on the air filter housing for the new filter. Could find it in any other the other videos.
Pro tip for the fuel filter replacement. Lossen the 3 7/16 cap bolts but do not remove them. Do not disconnect any of the fuel lines. Instead, leave everyting on including the clamp bolt. From inside the vehicle while sitting in the drivers seat, remove the 2 7/16 bolts that hold the fuel filter bracket. Fuel filter with housing is now easier to move around to remove the 3 cap bolts to service the filters (green screen and molded paper filter). Clear the drain line. Clean the inside and fill halfway up with fuel and install new filters then the cap with a new o-ring.
Place the oring in a zip loc bag and put it in the freezer overnight to shrink it. To prime, loosen the stainless steel screw at the top. Crank until only fuel comes out (no bubbles). Start and run the engine. Check for leaks then install into firewall by using an awl to center one of the bolt holes and install a bolt into the other. Tighten both once started. You're done.
CDR valve serice pro tip. So you dont drop that bottom clamp after you loosen it. Place a small zip tie under it so it doesn't slide down once it's loose.
I just bought a Humvee from GovPlanet, and its report says the motor doesn’t run. So, now I must binge watch your project vids so I’m better prepared for when it arrives. Thanks for documenting it all.
That’s what it’s all about!
Great information, it makes sense to change the filter for better air intake. Those original ones looks like designed for desert. Would have been great to know how it drives before and after.
am i the only one that noticed the grey shorts as she cranked...??? haha nice build man
I just installed my PCV valve. ( I thought it called the CDR valve ) whatever it called it stopped the smoke from oil filler which I thought was blow by. So glad that You started another project. Every video lerned something from you. Thanks for sharing.
Yes actually CDR. I’m so use to regular vehicles
Thanks for the usable content.
Ur video damn nearly made me cry. I had a border collie mutt named Jack. He was 15 last month when the vet had to put him to permanent rest
I bet he was a good boy
Dope video!!! We're with you! Please document the process of installing the interior insulation and noise deadening like lizard skin and or Dynomat.
Love your content and I hope you Chanel grow bigger and bigger
Thanks brother
Glad I found your site
Looking forward to the next!
Keep up a good work!!!!
Great.
Love your videos. I just won my Humvee last week . Now the wait time for release. Meanwhile I watch your videos .
Can you add links to the parts you install on the videos ?
That’s awesome!!
Do you have an update video or picture of how much you cut out on the air filter housing for the new filter. Could find it in any other the other videos.
I haven’t cut it yet, I will after the body gets on!
Why are the B pillars cut out?
I have no idea, picked it up like that.
"Moon sand" are you sure it was "definitely" overseas or off-world 😂?
😆that moon!!!!
What color use for this hummvee 😂😂
You’ll see
@@SplitBuilds 😂👍