For everyone wondering "why the hell do my subs not work?".. Do NOT connect your little 4 pin (white, gray, 2 black) Rear to "Rear In" on the input side of the amplifier. Instead connect your Rear to "Sub In" input on amplifier.. I've seen this question asked many times. This stage 6 system has great deep bass, alot of the other systems on the market lack it.
Great! Glad you were able to troubleshoot your system and get your subwoofers working. Greg does state at timecode 9:00 "Plug the harness labeled FRONT to the pigtail labeled FRONT, and the harness labeled REAR/SUBWOOFER into the pigtail labeled SUBWOOFER.
Um there is no wire labled rear/sub there’s three different connections front in, rear in, and sub in but no wires for sub from the head unit. What an I missing here?
@brianmonger3452 From the head unit side, front goes to front in (input side of amp) Rear goes to Sub In, (not rear on amp input like you would naturally think)
Be sure to look in the Amplifier wiring kit. You can see it’s included in that box rockfordfosgate.com/products/details/x317-k4/ If you still can’t find it, contact our customer support tomorrow at 1-800-669-9899.
The sub level is built into the PMX radio, so there is no "bass knob" available for this kit. We have pre-tuned the kit for the best overall performance and the sub level and built-in EQ can be fine tuned to your taste in music. However, keep in mind, this is an "open air" vehicle that has a different type of bass response compared to a "closed environment" like a car, truck, or SUV.
We see no body changes on the 2023 Can-Am X3 models, so you should be good to go. We typically reply in 24 hours or by Monday if submitted on Friday, so check your SPAM/JUNK filter.
The Accessory RED wire in the Can- Am is on top of the frame that supports the dash. It’s hard to find, but here’s a trick… stand in front of the car and have someone lift up the center dash panels. You’ll be able to see where it’s attached. At 8:55, you’ll see Greg has a short subwoofer adaptor harness. Both subs connect to one end, then plug the other end into the Power Connector side labeled SUB.
@@raptorKing5 You'll need an Accessory Power Harness Y-Adaptor: www.revzilla.com/motorcycle/xtc-power-products-power-splitter-accessory-harness-can-am-maverick-x3-maverick-r?sku_id=10142530
Dose this come with instructions because I don’t know nothing about electrical wiring I can mount and install everything up but not good at wiring stuff, do you think I got it or should I hire someone?
The video above are the step-by-step instructions. Everything is plug-and-play, but if you prefer, we have Authorized Dealers listed on our Dealer Locator at www.rockfordfosgate.com/dealerlocator/
Your wiring instructions are very poor and there’s connections that apparently go to nothing. Off the amplifier there’s three connections rear front and sub IN but only two connections front and rear is there not one for the sub?
Do you have this kit installed already? If not, I would suggest listening to it because it's freaking loud with the horn-loaded 8" tower speakers. However, technically you can add a 2nd set and run the rear channels of the amplifier at 2Ω, which the amp is stable at. This would be a custom installation, so you would be on your own since we don't have guides or instructions on how to do this.
You'll need to hard-wire the remote turn-on harness with a switch. This will require detaching the harness from the PMX radio that connects to the factory wiring under the dashboard. You can find that small harness attachment at timecode 09:40 in this section: ua-cam.com/video/FHnFNIvsUa0/v-deo.html
When connecting speakers with the RCA connectors, using the fader leaves the front dash and rear can speakers on the front channel. Seems like this is not using the full potential of this system?
The PMX-3 has RCA outputs for FRONT and REAR. We decided to use the REAR output as the SUBWOOFER control, allowing you to take advantage of the SUB (+) and SUB (-) buttons on the front of the radio. The video incorrectly states that the rear output is for the rear wake cans, as the rear is actually tied to the front speakers. Again, this allows us to adjust the bass level which is a frequently requested option.
6:45 - run the subwoofer harnesses from the steering column in the dash to the [under] seat location. 7:09 - install the subwoofers and plug the harness into each subwoofer connector (remove the black plug). 8:38 - wiring the amplifier starting with the output terminals of the amplifier. 8:57 - connect the subwoofer "Y" harness to the amplifier's subwoofer output. 9:00 - plug the harness from each subwoofer into the "Y" harness.
Dash speakers will make the steering pull hard right. you will have to have the steering reset at the dealership with no guarantee that it will fix the issue.
Hi Roberto, Yes you can add a backup cam. In fact we released a new MX-CAM with companion harness (MX-CAM-X317) on May 3rd. I also sent emails to everyone who subscribed to the "Notify Me When In Stock" on April 29 when Stage 6 started shipping. Lastly, our COMPATIBILITY chart does show fitment on your "2021 X3 Max X RS Turbo RR". Below are some handy links for you: • MX-CAM: rockfordfosgate.com/products/details/mx-cam/ • X317-STG6: rockfordfosgate.com/products/details/x317-stg6/
For everyone wondering "why the hell do my subs not work?".. Do NOT connect your little 4 pin (white, gray, 2 black) Rear to "Rear In" on the input side of the amplifier. Instead connect your Rear to "Sub In" input on amplifier.. I've seen this question asked many times. This stage 6 system has great deep bass, alot of the other systems on the market lack it.
Great! Glad you were able to troubleshoot your system and get your subwoofers working. Greg does state at timecode 9:00 "Plug the harness labeled FRONT to the pigtail labeled FRONT, and the harness labeled REAR/SUBWOOFER into the pigtail labeled SUBWOOFER.
@@rockfordfosgate I've watched this video so many times and I must've just been deaf...to many years of your product you see 😅
@@allenr2707 We have the same problem ... had to watch it a couple times to make sure 😂
Um there is no wire labled rear/sub there’s three different connections front in, rear in, and sub in but no wires for sub from the head unit. What an I missing here?
@brianmonger3452 From the head unit side, front goes to front in (input side of amp) Rear goes to Sub In, (not rear on amp input like you would naturally think)
What’s gonna happen to the cigarette outlet plug when installing the PMX-3?
It will still be there, but blocked-off. You can use an extension and route it to another location.
It goes connected to the bus bar or straight to the battery?
At 13:10 you can see Greg wire the B+ and GND directly to the battery.
Im missing the sub output short harness from my stage 6 that i just received
Be sure to look in the Amplifier wiring kit. You can see it’s included in that box rockfordfosgate.com/products/details/x317-k4/
If you still can’t find it, contact our customer support tomorrow at 1-800-669-9899.
Dose a bass knob come included or do I have to buy one?
The sub level is built into the PMX radio, so there is no "bass knob" available for this kit. We have pre-tuned the kit for the best overall performance and the sub level and built-in EQ can be fine tuned to your taste in music. However, keep in mind, this is an "open air" vehicle that has a different type of bass response compared to a "closed environment" like a car, truck, or SUV.
Will this fit the 2023 x3 max x rs turbo rr with smart shocks . I sent a email but no reply. The website hasn't been updated for 2023 models.
We see no body changes on the 2023 Can-Am X3 models, so you should be good to go. We typically reply in 24 hours or by Monday if submitted on Friday, so check your SPAM/JUNK filter.
Yes, it does and it hammers!
@@rockfordfosgatedoes this work on the 2024 model?
@@ovvclan9751 This fits most Maverick X3 models. You can check our compatibility chart here: rockfordfosgate.com/products/details/x317-stg6/
Does this run on the stock battery or does it need to be upgraded?
Yes Kyle, all Can-Am systems we have developed run off the stock electrical system.
Where is the power wire connect to at minute 9:41? Also what do I connect to the sub in? I connected the front in and rear in.
The Accessory RED wire in the Can- Am is on top of the frame that supports the dash. It’s hard to find, but here’s a trick… stand in front of the car and have someone lift up the center dash panels. You’ll be able to see where it’s attached. At 8:55, you’ll see Greg has a short subwoofer adaptor harness. Both subs connect to one end, then plug the other end into the Power Connector side labeled SUB.
@@rockfordfosgateif i have installed in that plug the system for signal lights, what can i do.?
@@raptorKing5 You'll need an Accessory Power Harness Y-Adaptor: www.revzilla.com/motorcycle/xtc-power-products-power-splitter-accessory-harness-can-am-maverick-x3-maverick-r?sku_id=10142530
Dose this come with instructions because I don’t know nothing about electrical wiring I can mount and install everything up but not good at wiring stuff, do you think I got it or should I hire someone?
The video above are the step-by-step instructions. Everything is plug-and-play, but if you prefer, we have Authorized Dealers listed on our Dealer Locator at www.rockfordfosgate.com/dealerlocator/
does Product come with all wiring i need to install?
Yes, the installation video above explains all the harnesses included in the kit.
What do i connect in sub in that goes in the amp?
I'm unsure what your question is, but the amplifier wiring can be found here: ua-cam.com/video/FHnFNIvsUa0/v-deo.html
Your wiring instructions are very poor and there’s connections that apparently go to nothing. Off the amplifier there’s three connections rear front and sub IN but only two connections front and rear is there not one for the sub?
Can I add a second set ot Motocan to this system? If so, whats the best way to do it?
Do you have this kit installed already? If not, I would suggest listening to it because it's freaking loud with the horn-loaded 8" tower speakers. However, technically you can add a 2nd set and run the rear channels of the amplifier at 2Ω, which the amp is stable at. This would be a custom installation, so you would be on your own since we don't have guides or instructions on how to do this.
How can I connect the stage 6 so I can run it with the car off?
You'll need to hard-wire the remote turn-on harness with a switch. This will require detaching the harness from the PMX radio that connects to the factory wiring under the dashboard. You can find that small harness attachment at timecode 09:40 in this section:
ua-cam.com/video/FHnFNIvsUa0/v-deo.html
PRODUCT DETAILS
rockfordfosgate.com/products/details/x317-stg6/
Does it fit in a 23 xrc 72?
Models that have an intrusion bar can cause front speaker panel clearance issues, so we don't recommend based on this 1 criteria.
These instructions are horrible, it explains nothing in detail he’s talking as if we know which harness he’s speaking off 🤦
When connecting speakers with the RCA connectors, using the fader leaves the front dash and rear can speakers on the front channel. Seems like this is not using the full potential of this system?
The PMX-3 has RCA outputs for FRONT and REAR. We decided to use the REAR output as the SUBWOOFER control, allowing you to take advantage of the SUB (+) and SUB (-) buttons on the front of the radio. The video incorrectly states that the rear output is for the rear wake cans, as the rear is actually tied to the front speakers. Again, this allows us to adjust the bass level which is a frequently requested option.
Where does the sub in cable connect to from the amp
6:45 - run the subwoofer harnesses from the steering column in the dash to the [under] seat location.
7:09 - install the subwoofers and plug the harness into each subwoofer connector (remove the black plug).
8:38 - wiring the amplifier starting with the output terminals of the amplifier.
8:57 - connect the subwoofer "Y" harness to the amplifier's subwoofer output.
9:00 - plug the harness from each subwoofer into the "Y" harness.
Dash speakers will make the steering pull hard right. you will have to have the steering reset at the dealership with no guarantee that it will fix the issue.
This anomaly is covered in our technical article “Can-Am X3 power steering torque offset reset” rftech.custhelp.com/app/answers/detail/a_id/1374/
😂😂😂 it’s an easy fix relax brother
Can I add reverse camera? When will Stage 6 be available? Is it compatible with 2021 X3 Max X RS Turbo RR?
Hi Roberto, Yes you can add a backup cam. In fact we released a new MX-CAM with companion harness (MX-CAM-X317) on May 3rd. I also sent emails to everyone who subscribed to the "Notify Me When In Stock" on April 29 when Stage 6 started shipping. Lastly, our COMPATIBILITY chart does show fitment on your "2021 X3 Max X RS Turbo RR". Below are some handy links for you:
• MX-CAM: rockfordfosgate.com/products/details/mx-cam/
• X317-STG6: rockfordfosgate.com/products/details/x317-stg6/