As you've noticed the one one the left is for 1v/oct tracking (scaling)and the right is for you default knob position if you like. This is for calibration, I'm assuming they have temperature compensation as it's an analogue circuit. You would normally set the reference frequency using the knob (eg: C2, doesn't really matter) and hit C3 and use the trimmer to adjust it. Go back to your reference and adjust the knob again and repeat the process until the scaling is correct. I would go 2 octaves, dial that in and then check 3 octaves and adjust if required. Once scaling is spot on set the Freq knob to centre and adjust the right trimmer to your reference. Same calibration for any VCO, there abouts. I noticed a similar issue with the Behringer 921 VCO...
"...so drop all your activities, buy a little screwdriver and do it. Goodbye." Awesome. I just got a Crave. I did notice the tiny recessed screws, but just added them to the list of a thousand other things I do not yet understand about the synth. And now, apparently, there are "notes" in a "scale" which have something to do with music. Who knew?
i actually stopped gaming/watching another Crave video on 2nd screen when i saw THIS thumbnail and was like oh yeah I'm doing this today cuz I got all the tools!
Once I made tuning my Model-D from a UA-cam tutorial . I did not watch this whole video, but I think the answer is the same as with Model-D. Now watch this video. :-)
This is one of the "joys" of a real analogue synth. It can also be really frustrating trying to get the "scaling" correct over a wide octave range...it's probably possible with a modern synth like the Crave but it was impossible on my old Pro-One. I guess that just adds to its character!
I just checked my Crave and when the Frequency knob is at 12 o'clock it is perfectly in tune (scaling and all) at A 440 Hz so I better leave it that way and not mess with it. The only inconveniece is that C key sounds like A but I can tune it with the frequency knob if I want to.
Its a common problem in analog synths. On some synths its not possible to tune the lowest vs the highest note, and therefor they should not be played with both bass and high notes at the same time, but be tuned for the used notes in the current song. You can hear the detuning problem on the Arp 2600, the Behringer Neutron and many other synths - but some of them can be tweaked somehow.
Standard calibration for any analogue synth. One is tuning, the other is called 'Scale'. If you mess it up too much you can spend hours trying to fix it. My polivoks is a pain to tune!
I tuned my Crave using the screw on the right and the other octaves are only 1 or 2 cents off, so I'm happy with that. But I wonder how to deal with the OSC knob. If it gets moved even slightly the tuning goes off. The only thing I could think to do is tape it down. Is there a better way to deal with this? If there was a click, or detent, so I knew the knob was centered then the problem would be solved. Any suggestions better than taping down the OSC knob would be great!
That's not midi. Midi is just information. If you press C, the midi out will just output the information that a C is played, no matter how the actual generator is tuned. Midi = ones and zeros CV = Volts per octave
I did the same with my Little Mcv. Use it to midi control an old MS20... That small but wonderful device works with either, V/Hz and V/oct, but each one requires a proper offset tunning...
@@AntonAnru I'm completely sure that the company that built that range of midi utilities closed long time ago... (Phillip Rees) So, the only way to get one is checking ebay or Reverb listings...
Hey man, I have some issues and would be so grateful if you will help. When I play a sequence and transpose it during playback, even if the MIDI-notes come from PC, even if i press the same key sequence starts - it transpose the sequence -2 octaves down. It works properly only with sequences in 4th octave and I don`t know why. The second problem is that when MIDI comes from PC the synth start playing, but doen`t end, when MIDI event ends. Thank you, your videos are great!
I followed the Behringer advice video on here for tuning my Model D and they ask you to tune it to an A note (A2 and A5 for each screw respectively)... Just wondering why the crave is tuned to a C note?? Thanks for posting this video!!! I got my Crave from Thomann and i think it's been out of tune since Day 1, so hopefully this sorts it!!! Now i just need to find out why my sequences are playing around 2 to 3 times faster than the clock that is coming from the RD-8... Anyone any ideas about that??
It doesn't really matter, A or C. I just chose it as the first note. And i didn't find guide lines for it so I tried to explore it from scratch. And I guess you way is gonna work to
Hey Anton, could you please help me out. Notes have mysteriously dropped in volume compared to others. Is there a way I could get them back even with the others?
спасибо за видео! для тех у кого нет такой отвертки, нужно сломать заколку-невидимку вашей девушки, и заточить ее конец пилочкой (если нашли заколку, то и пилка возможно неподалеку)
Anton, bro)) thank u for video. Is there any control of pitch range which we get from this freq osc nob near those screws? Короче, Бро, привет) мы как-то можм поменьше поставить freq диапазон? Я когда ручку поворачиваю полностью влево или вправо было бы логично на октаву получить шаг. Но к меня намного больше.
Никита, привет. Да, такое поведение ручки хотелось бы, но кажется это невозможно. Да и никто не общеал, что она октаву должна давать, просто свободная частота. Если даже диапазон Скейла можно подогнать в октаву вверх и вниз, то внутри октавы не будет строить. Там один винт это offsett, другой V/oct. Поэтому главная задача, чтобы чтобы осц нормально строил на широком диапазоне нот. У меня тоже не дает октавы вверх и вниз, шире получается
Антон, добрый день. Crave мой первый аналоговый синт) подскажите, из-за чего ableton видит не все ручки синтезатора? Пробовал на двух компах, везде одинаково. Не нашел видео с подключение его к ableton. Спасибо.
Евгений, приветствую. дело не в Ableton. оно так и есть - не все ручки с миди. media63.music-group.com/media/PLM/data/docs/P0DPX/CRAVE_QSG_WW.pdf вот в документе на 43 странице указано, какие с миди.
@@AntonAnru Еще вопрос, не разобрался в синхронизации по темпу, при нажатии play в ableton, играет какими-то отрывками, перескакивает вперед. На несколько секунд. Midi ставил USB. Подозреваю что и тут не разобрался)
дело не в $200. это аналоговый синт с частичным цифровым управлением. есть совсем трушные аналоговые, где вообще нет цифры, как в старые добрые, и стоить они могут дорого
Bro the biggest secret of this modern society is 432hz tuning and big healing properties of frequencies in 432hz = A spectrum. Lot's of ppl now making music by tuning their vst's to 432hz = A and repitching all of the samples 8hz down. This is amazing that crave can be tuned.
dont care for perfect tuning is you buy analog (its the charm) , these holes are very common since they calibrate the midi side to the analog side , scale is the offset in the 12 note interval , mess with that and it an take long before you find it again ,been doing this routine on kenton interfces since 30 years
Hi mate, screw on the left is pitch tune c2 do this one first, one on the right is scale tune c5. Double check 3340 docs to make sure though😊 it might be A on each octave like the model d
If you don't know what those are then don't touch them. They are for tracking and will have been set up at the factory so you get 1v per oct. Then again if you are not bothered about your crave being able to stay in tune across all your octaves then feel free to mess 😉
@@AntonAnru теперь стало понятно. Я не знаю почему но когда пропускаю crave через zoom ms50 g сигнал становится грязным , с каким бы пресетом не использовал. Даже через ableton и плагин Valhalla supermassive и то звук чище. Есть мысли на этот счет ?
Возможно вы используете vca/line выход, он даёт сильный сигнал, больше предназначенный для еврорек формата. Если его использовать для карт, микшера, педалей и тд, вероятен перегруз. Попробуйте с выходом phones, должно быть нормально
🏮 Presets for Behringer Crave: antonanru.sellfy.store/behringer/
Just finished tuning my Crave following your tutorial, 5 minutes ago. Makes a great difference! Thank you so much ❤
I'm glad it helped
@@AntonAnru it helped a whole lot, again thank you. Your channel is wonderful, of course I'm subscribed. Please keep on 👍
@@dianamiino7391 next is Edge. and then Edge+Crave combo patches
@@AntonAnru I Will Watch!
Brilliant mate! I got my crave yesterday and immediately noticed tuning problems..I couldn’t find anything either. Thanks for this explanation
As you've noticed the one one the left is for 1v/oct tracking (scaling)and the right is for you default knob position if you like.
This is for calibration, I'm assuming they have temperature compensation as it's an analogue circuit.
You would normally set the reference frequency using the knob (eg: C2, doesn't really matter) and hit C3 and use the trimmer to adjust it. Go back to your reference and adjust the knob again and repeat the process until the scaling is correct. I would go 2 octaves, dial that in and then check 3 octaves and adjust if required. Once scaling is spot on set the Freq knob to centre and adjust the right trimmer to your reference. Same calibration for any VCO, there abouts. I noticed a similar issue with the Behringer 921 VCO...
Interesting. It makes more sense to do the scaling first as you suggest.
You're an absolute legend. Thanks for sharing your secrets!
My pleasure
Thanks!!!!!! Finaly my crave is propperly in tune.
Hey maybe you can help me i cant tune it, both in midi and sequncer mode.
"...so drop all your activities, buy a little screwdriver and do it. Goodbye." Awesome. I just got a Crave. I did notice the tiny recessed screws, but just added them to the list of a thousand other things I do not yet understand about the synth. And now, apparently, there are "notes" in a "scale" which have something to do with music. Who knew?
That is pure drummer speak.......I can relate.... but hey, I beat(drums) and choke(cymbals) things as a passion ;)
haha
Very helpful - mine was set to A-sharp or something, - I've now tuned it up and it's MUCH more useful.
Mine came tuned to A440 at the center position.
Perfect. Great information and well presented
Thank you
Thank you. This video has very useful information
Welcome
Very cool bud, thank you for the tip 👍🏻..
Very valuable information!
Thanks Anton! Very well explained!
Welcome
Great vid bro. Thanks for sharing. ❤
you are welcome
Very good tutorial. Very helpful
You are welcome
Many thanks! Most useful
Great to know! Thanks!
I wondered if this was the case but was not brave enough to try, but now will have a go later today thanks so much
good luck with it
You’re so awesome, man! I’m doing this with my Crave, too! ❤️
Thank you
i actually stopped gaming/watching another Crave video on 2nd screen when i saw THIS thumbnail and was like oh yeah I'm doing this today cuz I got all the tools!
Good luck with it
thanks for this helpful video!
You're welcome
Good to know, thanks 👊
Welcome
Life saver.
💪
Very helpful video.......Thanks for the help!!!
You're welcome
excellent, mine arrived today.. that's a really useful video... nice work.
🙏
You're making this look a lot harder than it actually is.. 😂
for some people it's even harder than it's shown
Funny. I found it easier than the Behringer tuning tutorial of the Model D
Once I made tuning my Model-D from a UA-cam tutorial . I did not watch this whole video, but I think the answer is the same as with Model-D. Now watch this video. :-)
Hope this will help
Yeah, this video is easier
This is one of the "joys" of a real analogue synth. It can also be really frustrating trying to get the "scaling" correct over a wide octave range...it's probably possible with a modern synth like the Crave but it was impossible on my old Pro-One. I guess that just adds to its character!
Yes. And with the modern synth you have a choice: trying to perfect the tunning or leave it as it is
Moog were notorious for it.
Still beats the time that would get eaten up if you were foolish enough to move a mellotron around a few times...
Good job!
Thank you
Thanks
Welcome
Thank you
Thank you!
Thanks man!!!
Thanks mate
Glad to help
Я вчера подбуханный джемил и тоже решил покрутить эти подстроечные резики. Теперь придется настраивать)
Далеко зашёл джем)
Thanks! I just thought the Crave was not well tempered.
really helpful, thanks a lot :-)
you are welcome
thank you.👍🙌
I just checked my Crave and when the Frequency knob is at 12 o'clock it is perfectly in tune (scaling and all) at A 440 Hz so I better leave it that way and not mess with it. The only inconveniece is that C key sounds like A but I can tune it with the frequency knob if I want to.
That's the right decision. I had problems with tunning
Really good work, thank you!
You're welcome
Its a common problem in analog synths. On some synths its not possible to tune the lowest vs the highest note, and therefor they should not be played with both bass and high notes at the same time, but be tuned for the used notes in the current song. You can hear the detuning problem on the Arp 2600, the Behringer Neutron and many other synths - but some of them can be tweaked somehow.
Yes, it's a great option to set it and can hardly remember any other synth with this thing
Standard calibration for any analogue synth. One is tuning, the other is called 'Scale'. If you mess it up too much you can spend hours trying to fix it. My polivoks is a pain to tune!
what is the difference in tuning Polivoks/why is it a pain?
It takes ages. ua-cam.com/video/FAOOX4AQFog/v-deo.html
Thanks for this video : it was veryvery usefull !
You are welcome
I tuned my Crave using the screw on the right and the other octaves are only 1 or 2 cents off, so I'm happy with that. But I wonder how to deal with the OSC knob. If it gets moved even slightly the tuning goes off. The only thing I could think to do is tape it down. Is there a better way to deal with this? If there was a click, or detent, so I knew the knob was centered then the problem would be solved. Any suggestions better than taping down the OSC knob would be great!
unfortunately, you should always check it with tuner before the work
thank you man
welcome)
Awesome, thanks for sharing!
I gotta ask: what tuner are you using?
it's ableton tuner
@@AntonAnru ah, gotcha. Thanks
Cool, so first one is volts per octave range (midi) and second one is pitch shift. Liked the approach.
That's not midi. Midi is just information. If you press C, the midi out will just output the information that a C is played, no matter how the actual generator is tuned.
Midi = ones and zeros
CV = Volts per octave
🤟 Thanks Master!!!
Many thanks
welcome)
I did the same with my Little Mcv. Use it to midi control an old MS20...
That small but wonderful device works with either, V/Hz and V/oct, but each one requires a proper offset tunning...
thanks for the info, will check it
@@AntonAnru I'm completely sure that the company that built that range of midi utilities closed long time ago... (Phillip Rees)
So, the only way to get one is checking ebay or Reverb listings...
I've found one... take a look at the tech specs...
reverb.com/item/973959-philip-rees-little-mcv-midi-to-cv-converter
Have a look in any 3340 diy vco module. They explain how to calibrate.
Could you please share a link
I did it!
Hey man, I have some issues and would be so grateful if you will help. When I play a sequence and transpose it during playback, even if the MIDI-notes come from PC, even if i press the same key sequence starts - it transpose the sequence -2 octaves down. It works properly only with sequences in 4th octave and I don`t know why. The second problem is that when MIDI comes from PC the synth start playing, but doen`t end, when MIDI event ends. Thank you, your videos are great!
I followed the Behringer advice video on here for tuning my Model D and they ask you to tune it to an A note (A2 and A5 for each screw respectively)... Just wondering why the crave is tuned to a C note?? Thanks for posting this video!!! I got my Crave from Thomann and i think it's been out of tune since Day 1, so hopefully this sorts it!!! Now i just need to find out why my sequences are playing around 2 to 3 times faster than the clock that is coming from the RD-8... Anyone any ideas about that??
It doesn't really matter, A or C. I just chose it as the first note. And i didn't find guide lines for it so I tried to explore it from scratch. And I guess you way is gonna work to
@@AntonAnru Thnks for replying so quick!! :)
Hey Anton, could you please help me out. Notes have mysteriously dropped in volume compared to others. Is there a way I could get them back even with the others?
I guess it's some technical issue. Try to contact tech support
Thanks man....
Welcome)
Хорошо темперированный клавир
спасибо за видео! для тех у кого нет такой отвертки, нужно сломать заколку-невидимку вашей девушки, и заточить ее конец пилочкой (если нашли заколку, то и пилка возможно неподалеку)
Спасибо) тогда ещё нужен лайфхак для тех, у кого нет девушки
Anton, bro)) thank u for video. Is there any control of pitch range which we get from this freq osc nob near those screws?
Короче, Бро, привет) мы как-то можм поменьше поставить freq диапазон? Я когда ручку поворачиваю полностью влево или вправо было бы логично на октаву получить шаг. Но к меня намного больше.
Никита, привет. Да, такое поведение ручки хотелось бы, но кажется это невозможно. Да и никто не общеал, что она октаву должна давать, просто свободная частота. Если даже диапазон Скейла можно подогнать в октаву вверх и вниз, то внутри октавы не будет строить. Там один винт это offsett, другой V/oct. Поэтому главная задача, чтобы чтобы осц нормально строил на широком диапазоне нот. У меня тоже не дает октавы вверх и вниз, шире получается
What tuner did you use? I need to tune my Crave, thanks for this tutorial.
It's Ableton built-in tuner
@@AntonAnru I've got a code for a copy of Live Lite, I imagine it has a tuner in there as well.
@@AntonAnru Thanks!
Антон, добрый день. Crave мой первый аналоговый синт) подскажите, из-за чего ableton видит не все ручки синтезатора? Пробовал на двух компах, везде одинаково. Не нашел видео с подключение его к ableton. Спасибо.
Евгений, приветствую. дело не в Ableton. оно так и есть - не все ручки с миди.
media63.music-group.com/media/PLM/data/docs/P0DPX/CRAVE_QSG_WW.pdf
вот в документе на 43 странице указано, какие с миди.
@@AntonAnru Антон, спасибо за ответ, теперь увидел 😏 жаль конечно, но видимо я слишком много хочу за 200$😌
@@AntonAnru Еще вопрос, не разобрался в синхронизации по темпу, при нажатии play в ableton, играет какими-то отрывками, перескакивает вперед. На несколько секунд. Midi ставил USB. Подозреваю что и тут не разобрался)
дело не в $200. это аналоговый синт с частичным цифровым управлением. есть совсем трушные аналоговые, где вообще нет цифры, как в старые добрые, и стоить они могут дорого
попробуйте в настройках аудио поставить меньше buffer size, 32/64/128 и сверху меню options -> reduced latency
How offen do you have to tune it? Just one time or everytime you wanna Play with It?
Just one time
Интересно, почему они не сделали тоже самое в Нейтроне
But what is that little application that show you values?
it's Tuner. it's built-in Ableton Live deicve. You may also find a VST version, there are lots of them
Bro the biggest secret of this modern society is 432hz tuning and big healing properties of frequencies in 432hz = A spectrum. Lot's of ppl now making music by tuning their vst's to 432hz = A and repitching all of the samples 8hz down. This is amazing that crave can be tuned.
Sounds like "Equal Temperament" to me.
yes, the left screw is setting the distribution of the pythagorean comma
Of course. This wont do pythagorean or just intonation.
dont care for perfect tuning is you buy analog (its the charm) , these holes are very common since they calibrate the midi side to the analog side , scale is the offset in the 12 note interval , mess with that and it an take long before you find it again ,been doing this routine on kenton interfces since 30 years
Jak w gitarze, stroisz na główce i musisz ustawić menzurę na mostku.
What's the name of the tuner you are using?
It's ableton built-in tuner
@@AntonAnru thank you Anton 🙏
Great video, should we calibrate our crave because original it is unruly?
At least you should check your tubing thought out the octaves
Thanks but did not need it cause mine was perfectly calibrated.
What kind of tuner are you using?
Built-in Ableton live tuner
@@AntonAnru ahh nice. I just got ableton but haven’t messed around with it. Thanks!
You're welcome
Intonation (music)
Hi mate, screw on the left is pitch tune c2 do this one first, one on the right is scale tune c5. Double check 3340 docs to make sure though😊 it might be A on each octave like the model d
thank you. seems much easier. I could find this instruction for crave
Здравия. Есть вопрос к владельцам Crave. У моей модели не работает сиквенсер. Есть ли тут люди с подобной проблемой?
Проверьте clock sourse. Возможно стоит usb или др, а вы пускание без внешнего клока
@@AntonAnru Он работает только тогда когда подключен по миди. В нормальном режиме сиквенсер не работает. Там как то переключаются режимы?
Значит да, он ждёт внешнего клока. Переключиться легче всего через их приложение synth tribe
@@AntonAnru Благодарю. Попробую.
it's just like on a x0xb0x
Юси?
Юси
Май лук тюна
If you don't know what those are then don't touch them. They are for tracking and will have been set up at the factory so you get 1v per oct. Then again if you are not bothered about your crave being able to stay in tune across all your octaves then feel free to mess 😉
Добрый день, а можете обьяснить почему будучи русскоязычным человеком, вы записываете видео на английском?
больше аудитория
@@AntonAnru теперь стало понятно. Я не знаю почему но когда пропускаю crave через zoom ms50 g сигнал становится грязным , с каким бы пресетом не использовал. Даже через ableton и плагин Valhalla supermassive и то звук чище. Есть мысли на этот счет ?
Возможно вы используете vca/line выход, он даёт сильный сигнал, больше предназначенный для еврорек формата. Если его использовать для карт, микшера, педалей и тд, вероятен перегруз. Попробуйте с выходом phones, должно быть нормально
Thank you!
Welcome
thanks
Welcome